Honeywell ADEMCO VISTA SERIES Operating instructions

K3840V3 6/04 Rev A


$
$' '( (0 0& &2 2 9 9, ,6 67 7$ $ 6 6( (5 5, ,( (6 6 
9
9, ,6 67 7$ $   ) )% % 9 9, ,6 67 7$ $    ) )% % 
&RPPHUFLDO)LUHDQG%XUJODU\
3DUWLWLRQHG6HFXULW\6\VWHP
:LWK6FKHGXOLQJ

3URJUDPPLQJ*XLGH



































–2–
Table of Contents
Recommended Programming Procedure................. 3
Program Field Index ................................................. 4
VISTA-32FB/VISTA-128FB Programming Form...... 5
Partition-Specific Fields.......................................... 10
Programming With #93 Menu Mode....................... 12
Zone Programming................................................. 13
5800 Series Transmitters Loop Designations ........ 16
Expert Mode Zone Programming ........................... 17
Report Code Programming .................................... 21
Alpha Descriptors Programming ............................ 24
Alpha Descriptor Vocabulary.................................. 28
Device Programming .............................................. 29
Output Programming .............................................. 32
Relay Voice Descriptors .........................................36
Relay Voice Descriptors and Custom Word
Substitutes Vocabulary........................................37
Custom Word Substitutes for VIP Module
Annunciation........................................................37
System Layout Worksheets.................................... 38
Output Devices Worksheets ................................... 50
Scheduling Menu Prompts .....................................56
Scheduling Worksheets..........................................57
VISTA-32FB Summary of Connections Diagram ... 62
VISTA-128FB Summary of Connections Diagram .63
NOTE: All references in this manual for number of zones, user codes, partitions, VistaKey modules, the master
partition and the event log capacity, use the VISTA-128FB’s features. The following table lists the differences between
the VISTA-32FB and the VISTA-128FB control panels. All other features are identical for both panels.
Also, all procedures in this guide for entering zone numbers or user numbers show 3-digit entries, which is valid for
the VISTA-128FB. For the VISTA-32FB these entries are only 2-digit.
Feature VISTA-32FB VISTA-128FB
Partitions 2 8
Number of Zones 32 128
Number of User Codes 75 150
Master Partition 3 9
VistaKey Modules 4 8
The purpose of this document is to provide a quick and easy way to program your entire system. A recommended
programming procedure is included, followed by a list of program fields with the corresponding program group they belong to
(system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields,
and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fields
become system-wide fields.
Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your system
before programming is performed. If you need further information about specific programming options, see the VISTA-
32FB/VISTA-128FB Installation and Setup Guide.
Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."
Single-Partition System
The system default is for a single-partition system. Use the VISTA-32FB/VISTA-128FB SINGLE PARTITION
PROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDED
PROGRAMMING PROCEDURE of this document for proper programming procedure.
Multiple-Partition System
You must enter the number of partitions you are using in data field 2*00 to set the system for multiple partitions. Use the
VISTA-32FB/VISTA-128FB SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS when programming
the system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this
document for proper programming procedure.
SUMMARY OF PROGRAMMING COMMANDS
• To enter program mode, enter installer code + [8] + [0] + [0] + [0]. For the VISTA-32FB installer code + [8] + [0] + [0].
• To set standard defaults, press ✱97
• To change to next page of program fields, press ✱94
• To return to previous set of fields, press ✱99
• To erase account and phone number field entries, press [✱] + field number + [✱]
• To assign zone descriptors, press #93 + follow menu prompts
• To add custom words, press #93 + follow menu prompts
• To enter Installer's Message, press #93 + follow menu prompts
• To exit program mode, enter ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code.
✱98 prevents re-access to programming mode by installer code.
Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.

–3–
Recommended Programming Procedure
The following is a step-by-step procedure recommended for programming your system.
1. Set the keypads (and other peripheral devices) to the appropriate addresses.
2. Set factory defaults by pressing ✱97.
This will automatically enable keypad addresses 00-01, so be sure at least one keypad is set to one of these
addresses.
3. Program system-wide (global) data fields.
Using the programming form as a guide, enter program mode and program all system-wide programming
fields. These options affect the entire system, regardless of partitions. They include control options,
downloader and dialer options, RF options, event logging options, etc. Refer to the Program Field Index for a
listing of the program fields and their function.
Note that field 2✱00 (number of partitions) must be programmed before continuing.
4. Program partition-specific fields.
When the system-wide fields have been programmed, program all partition-specific programming fields by
first pressing ✱91 to select a partition (while still in data field program mode). Then enter the first partition-
specific field number ✱09. When you are finished, the next partition-specific field is automatically displayed.
Partition-specific fields can have different values for each partition. To program the fields for the next partition,
press ✱91, enter the desired partition number, then enter field ✱09. Refer to the MECHANICS OF
PROGRAMMING section in the VISTA-32FB/VISTA-128FB Installation and Setup Guide for detailed
instructions.
5. Use #93 Menu Mode for device programming.
Refer to Device Programming in this guide to assign keypad ID numbers and default partitions for each
keypad, and to selectively suppress certain keypad sounding options. Also use this mode to assign RF
receivers, relay modules, the VIP module, the ECP Long Range Radio, and the VISTA Gateway Module.
6. Use #93 Menu Mode for zone programming.
Refer to Zone Programming in this guide to program zone response types, assign right loop zones and
wireless zones, assign zones to partitions, and to program alarm report codes.
7. Use #93 Menu Mode for programming outputs.
Refer to Output Programming in this guide to program desired output operation.
8. Program Communication options.
Refer to System Communication section in the VISTA-32FB/VISTA-128FB Installation and Setup Guide for
detailed instructions. Then use #93 menu mode to program report codes.
9. Use #93 Menu Mode for programming alpha descriptors.
Refer to Alpha Programming in this guide to enter zone and partition descriptors and a custom installer’s
message.
10. Use #93 Menu Mode for relay voice descriptors and custom word substitutes.
Refer to Relay Voice Descriptors in this guide for further instructions for programming relay descriptors to be
annunciated by the VIP module, as well as the Custom Index section for custom word substitutes.
11. Use #80 Mode for programming schedules.
Refer to the Scheduling Menu Prompts in the VISTA-32FB/VISTA-128FB Installation and Setup Guide to
program open/close schedules, temporary and holiday schedules, limitation of access schedules, and time-
driven events.
12. Define user access codes.
Refer to User Access Codes in the VISTA-32FB/VISTA-128FB Installation and Setup Guide to program
authority level, O/C reporting option, partition assignments, and wireless key assignments for each user.
13. Exit Programming Mode.
Exit programming mode by pressing either ✱98 or ✱99. Additional entries of ✱99 are required if the exit is
being done from fields 1✱00 and above.
To prevent re-access to programming mode using the Installer’s code, use ✱98. The only way to re-access
programming mode is by depressing both the [✱] and [#] keys at the same time within 30 seconds of power-
up.
Exiting by using ✱99 always allows reentry into programming mode using the Installer code. Either way of
exiting allows access via downloading. Note that if local programming lockout is set via downloading,
programming mode cannot be entered at the keypad.

–4–
Program Field Index
On the following pages, the programming fields have been arranged in numerical order. Use this index to cross-reference the
fields on the programming form.
Field Group Field Group Field Group
*00 System-Wide
*08 System-Wide
*09 Partition-Specific
*10 Partition-Specific
*11 Partition-Specific
*12 Partition-Specific
*13 Partition-Specific
*15 System-Wide
*16 Partition-Specific
*17 System-Wide
*19 System-Wide
*20 System-Wide
*22 Partition-Specific
*23 Partition-Specific
*24 System-Wide
*25 System-Wide
*26 Communications
*27 Communications
*28 System-Wide
*29 Partition-Specific
*30 Communications
*31 Communications
*32 Partition-Specific
*33 Communications
*34 Communications
*35 System-Wide
*36 System-Wide
*37 System-Wide
*38 Partition-Specific
*39 Partition-Specific
*40 Communications
*41 System-Wide
*42 Communications
*43 Communications
*44 Communications
*45 Communications
*46 Communications
*47 Communications
*48 Communications
*49 Communications
*50 Communications
*51 Communications
*52 Communications
*53 Communications
*54 System-Wide
*56 Communications
*57 Communications
*58 Communications
*59 Communications
*64 Communications
*65 Communications
*66 Communications
*67 Communications
*68 Communications
*69 Communications
*70 Communications
*71 Communications
*72 Communications
*73 Communications
*74 Communications
*75 Communications
*76 Communications
*79 Communications
*80 Communications
*83 Communications
*84 Partition-Specific
*85 Partition-Specific
*87 Partition-Specific
*88 Partition-Specific
*89 Communications
*90 Partition-Specific
1*17 System-Wide
1*18 Partition-Specific
1*19 Partition-Specific
1*20 System-Wide
1*21 System-Wide
1*22 System-Wide
1*23 System-Wide
1*24 System-Wide
1*25 System-Wide
1*26 Partition-Specific
1*28 System-Wide
1*29 System-Wide
1*30 System-Wide
1*31 System-Wide
1*33 Communications
1*34 Communications
1*35 Communications
1*42 Communications
1*43 Partition-Specific
1*44 System-Wide
1*45 Partition-Specific
1*47 Partition-Specific
1*48 System-Wide
1*49 System-Wide
1*52 Partition-Specific
1*53 System-Wide
1*56 System-Wide
1*57 System-Wide
1*58 System-Wide
1*60 System-Wide
1*70 System-Wide
1*71 System-Wide
1*72 System-Wide
1*73 System-Wide
1*74 System-Wide
1*75 System-Wide
1*76 Partition-Specific
1*77 System-Wide
2*00 System-Wide
2*01 System-Wide
2*02 System-Wide
2*05 Partition-Specific
2*06 Partition-Specific
2*07 Partition-Specific
2*08 Partition-Specific
2*09 Partition-Specific
2*10 Partition-Specific
2*11 System-Wide
2*18 Partition-Specific
2*19 Partitioning
2*20 Partition-Specific
2*21 System-Wide
2*22 Partition-Specific
2*23 Partition-Specific
2*24 Partition-Specific
3*00 System-Wide
3*01 System-Wide
3*12 System-Wide
3*13 System-Wide
3*14 System-Wide
3*15 System-Wide
3*16 System-Wide
3*17 System-Wide
3*18 System-Wide
3*19 System-Wide
3*20 System-Wide
3*21 System-Wide
3*30 System-Wide
3*31 System-Wide
3*50 System-Wide
3*55 System-Wide
3*56 System-Wide
3*57 Partition-Specific
3*59 Partition-Specific
3*60 Partition-Specific
3*61 System-Wide
3*82 System-Wide
3*85 System-Wide

–5 –
VISTA-32FB/VISTA-128FB Programming Form
Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system,
see the Partition-Specific Fields section for programming these fields. Standard default (*97) values are shown in brackets [ ];
otherwise, default = 0.
*00 INSTALLER CODE | | |
Enter 4 digits, 0-9 [5140]
*08 TEMPORAL SIREN PULSE [0]
1=enable; 0=disable
*09 ENTRY DELAY #1 [02] |
00, 02-15 times 15 seconds
Maximum "03" for UL Commercial Burglary installations.
*10 EXIT DELAY #1 [03] |
00, 03-15 times 15 seconds
Maximum "04" for UL Commercial Burglary installations.
*11 ENTRY DELAY #2 [06] |
00, 02-15 times 15 seconds (must be longer than Entry Delay
#1). Maximum "03" for UL Commercial Burglary installations.
*12 EXIT DELAY #2 [08] |
00, 03-15 times 15 seconds (must be longer than Exit Delay
#1). Maximum "04" for UL Commercial Burglary installations.
*13 BELL 1 TIMEOUT [04] |
01-15 times 2 minutes. Minimum 16 minutes for UL
Commercial Burglary installations and minimum 6 minutes for
UL Commercial Fire installations
*15 KEYSWITCH ASSIGNMENT [0]
Enter partition in which keyswitch used, 1-8; 9=silences
Notification Appliance Circuit if fire present; 0=disable
*16 BELL 1 CONFIRMATION OF ARMING DING [0]
1=enable; 0=disable.
Must be "1" for UL Commercial Burglary installations.
*17 AC LOSS KEYPAD SOUNDING [0]
1=enable; 0=disable
*19 RANDOMIZE AC LOSS REPORT [2]
1=10-40 min; 2= 6-12 hours; 0=normal report (about 2 min.
after AC loss).
Must be “2”for central and remote fire alarm systems.
*20 VIP MODULE PHONE CODE | |
Enter 01 - 09 for the first digit; enter [00], [11]
11 for “*”or 12 for “#”for the second digit.
Must be set to "0" for UL Commercial Burglary and UL
Commercial Fire installations.
*22 KEYPAD PANIC ENABLES [001]
1=enable; 0=disable 995 996 999
*23 MULTIPLE ALARMS [1]
1=enable; 0=disable
Must be “1”for UL Commercial Burglary installations
*24 IGNORE EXPANSION ZONE TAMPER [0]
1=Ignore; 0=Enable tamper for RF and RPMs.
Must be "0" for UL Commercial Burglary and Commercial Fire
installations if using these devices.
*25 BURG.TRIGGER FOR RESPONSE TYPE 8 [1]
1=enable; 0=disable
*26 INTELLIGENT TEST REPORTING [0]
1=enable (no report sent if any other report was recently sent);
0=disable (send report at programmed interval, field *27)
Must be “0”for UL Commercial Burglary and Commercial Fire
installations.
*27 TEST REPORT INTERVAL [024] | |
Enter interval in hours, 001-999; 000=no report;
Max. 024 for UL Commercial Burglary and Commercial Fire
installations.
*28 POWER UP IN PREVIOUS STATE [1]
1=enable; 0=disable
Must be “0”for UL Commercial Burglary and Commercial Fire
installations.
*29 QUICK ARM [1]
1=enable; 0=disable
*30 MAIN DIALER TOUCHTONE OR ROTARY [0]
1=TouchTone; 0=rotary
*31 PABX ACCESS CODE | | | |
00-09; B-F (11-15)
*32 PRIM. SUBS. ACCT # | | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
*33 PRIMARY PHONE NUMBER
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*34 SECONDARY PHONE NUMBER
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*35 DOWNLOAD PHONE NO.
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*36 DOWNLOAD ID NO.
| | | | | | | |
Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]

–6 –
*37 DOWNLOAD COMMAND ENABLES
Dlr Shtdwn Sys Shtdwn
0
Not Used Rmt Byp Rmt Disarm Rmt Arm Upld Pgm Dwnld Pgm
See field 1*53 for Callback disable option; [1=enable];
0=disable. For UL Commercial Burglary and Commercial Fire
installations, all entries must be "0."
*38 PREVENT ZONE XXX BYPASS [000] | |
001-128; 00 if all zones can be bypassed
*39 ENABLE OPEN/CLOSE REPORT FOR [1]
INSTALLER CODE 1=enable; 0=disable
*40 OPEN/CLOSE REPORT FOR KEYSWITCH [0]
1=enable; 0=disable
*41 NORMALLY CLOSED or EOLR (Zones 3-8) [0]
1=N.C.loops; 0=EOLR supervision.
Must be "0" for UL Commercial Burglary and Commercial Fire
installations.
*42 DIAL TONE PAUSE [0]
0=5 seconds; 1=11 seconds; 2=30 seconds.
Must be "0" UL Commercial Burglary and Commercial Fire
installations.
*43 DIAL TONE DETECTION [1]
1=wait for true dial tone; 0=pause, then dial
*44 RING DETECTION COUNT [00] |
01-14; 15=answering machine; 00=no detection.
Must be "00" for UL Commercial Burglary and Commercial Fire
installations.
*45 PRIMARY FORMAT [0]
0=Low Speed; 1=Contact ID; 2=ADEMCO High Speed;
3= ADEMCO Express
*46 LOW SPEED FORMAT (Primary) [0]
0= ADEMCO Low Speed; 1=Sescoa/Radionics
*47 SECONDARY FORMAT [0]
0=Low Speed; 1=Contact ID; 2= ADEMCO High Speed;
3= ADEMCO Express
*48 LOW SPEED FORMAT (Sec.) [0]
0= ADEMCO Low Speed; 1=Sescoa/Radionics
*49 CHECKSUM VERIFICATION [0] [0]
1=enable; 0=disable Prim Sec
*50 SESCOA/RADIONICS SELECT [0]
1=Sescoa; 0=Radionics
*51 DUAL REPORTING [0]
1=yes; 0=no If used with Spilt Reporting "1" option (1*34),
alarms and alarm restores go to both primary & secondary
numbers, while all other reports go to secondary only. If used
with Split Reporting "2" option, alarms and alarm restores go
to both, open/close and test messages go to secondary only,
while all other reports go to primary. If used with Split
Reporting “3”option, fire alarms and fire supervisory signals
go to both, all other reports go to secondary only.
*52 STANDARD/EXPANDED REPORT FOR PRIMARY
[0 0 0 0 0 0]
Alarm Rstr Byp Trbl O/C LoBat
0=standard; 1=expanded;
Note: Expanded overrides 4+2 format.
*53 STANDARD/EXPANDED REPORT FOR SECONDARY
[0 0 0 0 0 0]
Alarm Rstr Byp Trbl O/C LoBat
0=standard; 1=expanded;
Note: Expanded overrides 4+2 format.
*56 DYNAMIC SIGNALING DELAY [00] |
Select the delay time (00-15) times 15 seconds before sending
to second destination.
*57 DYNAMIC SIGNALING PRIORITY [0]
0=Primary dialer; 1=LRR, as first reporting destination.
*58 LRR CENTRAL STATION #1 CATEGORY ENABLE
[0 0 0 0 0 0]
Alarm Trbl Byp O/C Syst Test
0=disable, 1=enable for reports for primary subs ID of LRR
*59 LRR CENTRAL STATION #2 CATEGORY ENABLE
[0 0 0 0 0 0]
Alarm Trbl Byp O/C Syst Test
0=disable, 1=enable for reports for secondary subs ID of LRR
*64 PAGER INSTALLED [0]
0=No, 1=Yes, alpha numeric pager interface is installed.
*65 PAGER PHONE # FOR ALARMS
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*66 PAGER ID # FOR ALARMS
Enter up to 10 digits for the pager id #
*67 PAGER PHONE # FOR SUPERVISION
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*68 PAGER ID # FOR SUPERVISION
Enter up to 10 digits for the pager id #
*69 PAGER PHONE # FOR BYPASSES
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*70 PAGER ID # FOR BYPASSES
Enter up to 10 digits for the pager id #
*71 PAGER PHONE # FOR OPENS/CLOSES
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause

–7 –
*72 PAGER ID # FOR OPENS/CLOSES
Enter up to 10 digits for the pager id #
*73 PAGER PHONE # FOR SYSTEM
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*74 PAGER ID # FOR SYSTEM
Enter up to 10 digits for the pager id #
*75 PAGER PHONE # FOR TEST
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
*76 PAGER ID # FOR TEST
Enter up to 10 digits for the pager id #
ZONE TYPE RESTORE ENABLES
*79 FOR ZONE TYPES 1-8
1 2 3 4 5 6 7 8
1=enable; [0=disable]
*80 FOR TYPES 9 and 10
9 10
1=enable; [0=disable]
*83 FIRST TEST REPORT TIME | | |
[Day 00; hour 12; min 00]. Days 01-07, Hours 00-23, Min 00-
59; 00 in all boxes = instant (Day 01= Monday)
*84 SWINGER SUPPRESSION [03] |
01-15 alarms
Must be "00" (disabled) for UL Commercial Burglary and
Commercial Fire installations.
*85 ENABLE DIALER REPORTS FOR PANICS & DURESS
1=enable; [0=disable]
995 996 999 Duress
*87 ENTRY WARNING [1]
1=continuous; 0=3 beeps
*88 BURG. ALARM COMM. DELAY [0]
1=16 seconds; 0=no delay
Must be "0" for UL Commercial Burglary installations.
*89 RESTORE REPORT TIMING [0]
0=Instant; 1=After bell timeout if zone is restored; 2=when
system is disarmed. Must be "0" for UL Commercial Burglary
and Commercial Fire installations.
*90 SEC. SUBS. ACCT # | | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
1*17 LOBBY PARTITION [0]
Enter the "common lobby" partition (1-8)
1*18 AFFECTS LOBBY [0]
Enter 1 if this partition affects the common lobby;
Enter 0 if it does not.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*19 ARMS LOBBY [0]
Enter 1 if arming this partition attempts to arm lobby;
Enter 0 if it does not.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*20 EXIT ERROR LOGIC ENABLE [0]
0=No; 1=Bypass E/E and Interior zones faulted after exit
delay.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*21 EXIT DELAY RESET [0]
0=No; 1=Resets Exit Delay to programmed value after zone
is closed and then faulted prior to end of exit delay.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
FIELDS 1✳22-1✳25: Allow four sets of two zones each to be linked
so that both must fault within a five minute period to cause an alarm.
Default for these fields = [000], [000].
1*22 CROSS-ZONING PAIR ONE | | | |
1*23 CROSS-ZONING PAIR TWO | | | |
1*24 CROSS-ZONING PAIR THREE | | | |
1*25 CROSS-ZONING PAIR FOUR | | | |
1*26 PANIC BUTTON OR SPEEDKEY
[00, 00, 00, 00] |
A
|
B
|
C
|
D
Enter speedkey macro # (01-35) to use keys A-C for macro.
Otherwise enter 00 to use as panic. For D key, enter macro
# or 00 to select macro when key is pressed.
33 = fire sounder silence.
34 = display next fire alarm.
35 = display previous fire alarm.
NOTE: For selection 33 enable field 3✳15 for pulsing. For
selections 34 and 35 set field 3✳01.
Fields 1*28 - 1*31 are not applicable for UL Commercial
Burglary and Commercial Fire installations.
1*28 RF TX LOW BATTERY SOUND [0]
1=immediate; 0=when disarmed
1*29 RF TX LOW BATTERY REPORTING [0]
1=enable; 0=disable
1*30 RF RCVR CHECK-IN INTERVAL [02] |
02-15 times 2 hours; 00 disables supervision
1*31 RF XMITTER CHECK-IN INTERVAL [02] |
02-15 times 2 hours; 00 disables transmitter supervision
1*33 TOUCHTONE W/ROTARY BACKUP [0]
1=enable; 0=disable

–8 –
1*34 COMM. SPLIT REPORTING [0]
0=no; 1=alarms and alarm restores primary, others
secondary; 2=open/close, test secondary, others primary;
3=fire alarms & troubles primary, all others to secondary.
See
7 51 for comments if using with dual reporting.
1*35 ACCESS CONTROL DIALER ENABLES
[0 0 0 0 0 0]
Trace Trbl Byp Not Used Syst Alm
1=enable; 0=disable
1*42 CALL WAITING DEFEAT [0]
1=enable; 0=disable
1*43 PERM. KEYPAD BACKLIGHT [0]
1=enable; 0=disable, when disabled, display lights when any
key is pressed, and turns off after period of keypad inactivity.
1*44 WIRELESS KEYPAD TAMPER [0]
DETECTION
1=enable; 0=disable.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*45 EXIT DELAY SOUNDING [0]
1=enable; 0=disable. Produces quick beeping during exit
delay if enabled.
1*47 CHIME ON BELL 1 [0]
1=enable; 0=disable
1*48 WIRELESS KEYPAD ASSIGNMENT [0]
0=disable; enter partition in which RF keypad used, 1-8.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*49 SUPPRESS TX SUPERVISION SOUND [1]
1=disable; 0=enable.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*52 SEND CANCEL IF ALARM + OFF [0]
1=no restriction; 0=within bell timeout period only.
1*53 DOWNLOAD CALLBACK [0]
1=callback not required; 0=callback required.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*56 AC 50/60 Hz CLOCK SPEED [0]
1=50 Hz; 0=60 Hz.
1*57 5800 RF BUTTON GLOBAL ARM [0]
1=enable; 0=disable
1*58 5800 RF BUTTON FORCE ARM [0]
1=enable. If a zone is faulted after pressing button, console
will beep once. User should press button again within 4 sec.
to force bypass those zones. 0=disable.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*60 ZONE 5 AUDIO ALARM VERIFICATION [0]
Enter 1 if 2-way audio (AAV) is being used; Enter 0 if it is not.
Must be "0" for UL Commercial Burglary and Commercial
Fire installations.
1*70 EVENT LOG TYPES
[1 0 0 0 1 0]
Alarm Chk Byp O/C Syst Test
1=enable; 0=disable
1*71 12/24 HOUR TIME STAMP FORMAT [0]
0=12 hour; 1=24 hour
1*72 EVENT LOG PRINTER ON-LINE [0]
0=disable; 1=enable
1*73 PRINTER BAUD RATE [0]
1=300; 0=1200
1*74 RELAY TIMEOUT XXX MINUTES [000] | |
Enter relay timeout, 0-127 in multiples of 2 minutes, desired
for #80 Menu Mode time-driven event relay command
numbers "04/09" and #93 Menu Mode Output Programming
output command "56."
1*75 RELAY TIMEOUT YYY SECONDS [000] | |
Enter relay timeout, 0-127 seconds, desired for #80 Menu
Mode time driven event relay command numbers "05/10" and
#93 Menu Mode Output Programming command "57."
1*76 ACCESS CONTROL RELAY [00] |
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter 00-96; 00=none.
Must be "00" for UL Commercial Burglary and Commercial
Fire installations.
1*77 LOG FIRST MAINTENANCE SIGNAL [0]
0=No Log; 1=Log first maintenance signal from each smoke
detector.
3rd Page Programming Fields (press *94)
2*00 NUMBER OF PARTITIONS [1]
Enter 1-8
2*01 DAYLIGHT SAVING TIME [04, 10] | |
START/END MONTH Start End
00-12; if no daylight saving time, enter 00,00
2*02 DAYLIGHT SAVING TIME [1, 5] |
START/END WEEKEND Start | End
Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next
to last; 7=3rd from last [1,5]
2*05 AUTO-ARM DELAY [15] |
Enter the time between the end of the arming window and the
start of auto-arming warning period, in values of 1-14 times 4
minutes 00=instant; [15=no auto arm at all]. When this delay
expires, the Auto-Arm Warning Period begins.
2*06 AUTO-ARM WARNING PERIOD [15] |
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps every
15 seconds; "ALERT" displayed). Enter 01-15 minutes.
00=instant at end of arming delay.
2*07 AUTO-DISARM DELAY [15] |
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4 minutes;
00=instant at end of window; 15=no auto-disarm.
2*08 ENABLE FORCE ARM FOR AUTO-ARM [0]
0=disable; 1=enable

–9 –
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
1=enable; 0=disable
If enabled, only openings and closings occurring outside the
scheduled opening/closing windows will trigger dialer reports.
Opening reports will also be suppressed during the closing
window, in order to prevent false reports when the user arms
the system and then reenters the premises to retrieve a
forgotten item.
2*10 ALLOW DISARMING ONLY DURING [0]
ARMING/DISARMING WINDOWS
0=disable; 1=enable
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installation.
2*11 ALLOW DISARM OUTSIDE WINDOW [0]
IF ALARM OCCURS
Used only if field 2*10 (partition-specific field) is set to "1." If
this field is enabled ("1") the system can be disarmed outside
the disarm window if an alarm has occurred. If "0," disarming
can only be done during the disarm window. If field 2*10 is
set to "0" for a partition, this field has no effect for that
partition.
2*18 ENABLE GOTO FOR THIS PARTITION [0]
1=Allow log-on from other partitions; 0=disable
2*19 USE PARTITION DESCRIPTORS [0]
0=disable; 1=enable
2*20 ENABLE J2 TRIGGERS FOR PARTITION [1]
0=disable for displayed partition; 1=enable for displayed
partition
2*21 ENABLE SUPERVISION PULSES FOR LRR
TRIGGER OUTPUTS [00000]
F B P S T
Used for supervised connection to 7920SE.
Enter 0 to disable or 1 to enable the listed outputs.
F= Fire; B= Burglary; P= Audible Panic; S= Silent
Panic/Duress; T= Trouble.
Must be “1”for UL Commercial Burglary and Commercial Fire
installations.
2*22 DISPLAY FIRE ALARMS OF [0]
OTHER PARTITIONS
0=disable; 1=enable.
2*23 DISPLAY BURG & PANIC ALARMS OF [0]
OTHER PARTITIONS
0=disable; 1=enable.
2*24 DISPLAY TROUBLES OF OTHER [0]
PARTITIONS
0=disable; 1=enable
4th Page Programming Fields (press *94)
3*00 DISPLAY TRBL INSTEAD OF CHECK [0]
0=CHECK; 1=TRBL
3*01 FIRE DISPLAY LOCK [0]
0=scroll all alarms; 1=lock display of first fire alarm
3*12 ZN TYPE 18 DELAY USE [1]
0=disable; 1=enable
3*13 SUPV. N.O./N.C. SELECTION [0]
0=Supv on short/trouble on open; 1=supv. On short or open
3*14 WATERFLOW SILENCE OPTION [0]
0=silence on code = off; 1=silence when waterflow restores
3*15 ALARM BELL SOUND [1,0]
0=pulsed; 1=steady Bell 1 Bell 2
3*16 DELAY FOR ZONE TYPE 17 & 18 [00] |
Enter 00-15 times 2 seconds
3*17 ALTERNATE FUNCTION (TAMPER) [0]
FOR ZONE 6 0=disable; 1=enable
3*18 EXTENDED DELAY FOR TYPES 17 & 18 [0]
0=disable; 1=enable
3*19 ENABLE J2 HEADER PRINTER PORT [0]
0=pins 5 & 9function as per filed 3*20;
1=pins 5 & 9 function as RXD & DTR
3*20 TRIGGER OUTPUT SELECTION [0]
0=LRR full connection & remote console sounder;
1=LRR limited connection & keyswitch LEDs
3*21 MAX NUMBER OF DIALER ATTEMPTS [8]
1-8 (3, 4 or 5for NFPA72 compliant systems when a
secondary phone number is programmed (field *34))
3*30 DIALER SELCTION [1,0]
0=disable; 1=enable Main Backup
3*31 BACKUP DIALER TOUCHTONE/ROTARY [0]
1=TouchTone; 0=Rotary
3*50 ZONE TYPE RESTORE ENABLES
FOR ZONE TYPES 16-18
1=enable; [0=disable]
3*55 RESET ON SECOND OFF FOR BELL 1 [0]
0=disable; 1=enable
3*56 RESET ON SECOND OFF FOR BELL 2 [0]
0=disable; 1=enable
3*57 BELL 2 & AUX RELAY CONFIRM [0,0]
ARMING DING Bell 2 Aux
0=disable; 1=enable. Must be “1”for UL Commercial Burglary
installations.
3*59 ENABLE BELL 2 & AUX RELAY [0,0]
CHIME ANNUNCIATION Bell 2 Aux
0=disable; 1=enable
3*60 BELL 2 & AUX RELAY TIMEOUT | |
Bell 2 Aux
Enter 00-15 times 2 minutes; 00=no timeout [00,00]
Minimum 16 minutes for UL Commercial Burglary
installations.
3*61 AUX RELAY FUNCTION [1]
0=trouble/supervisory; 1=alarm, silenced by code = off;
2=smoke detector reset; 3=battery save; 4=alarm, silenced
by code = # = 67
3*82 ENABLE BURG FEATURES ON PART 1 [1]
0=disable (disables AWAY, STAY, MAX, TEST, INSTANT &
CHIME); 1=enable;

–10 –
3*85 ENABLE FIRE & SYSTEM ZONE BYPASS [1]
0=disable; 1=only installer can bypass;
2=only installer & master can bypass.
Applies to fire zone types 9, 16, 17, & 18 and system zones
970-977 and to partition 1 only.
Partition-Specific Fields
(Duplicate this page for each partition in the installation.)
To program these fields,
1. Press *91 to select a partition.
2. Enter a partition-specific field number (ex. *09).
3. Make the required entry.
4. Repeat steps 1-3 for each partition in the system.
PARTITION #____ PROGRAM FIELDS
1st Page Fields
*09 ENTRY DELAY #1 [02] |
00, 02-15 times 15 seconds
Maximum "03" for UL Commercial Burglary installations.
*10 EXIT DELAY #1 [04] |
00, 03-15 times 15 seconds
Maximum "04" for UL Commercial Burglary installations.
*11 ENTRY DELAY #2 [06] |
00, 02-15 times 15 seconds (must be longer than Entry Delay
#1). Maximum "03" for UL Commercial Burglary installations.
*12 EXIT DELAY #2 [08] |
00, 03-15 times 15 seconds (must be longer than Exit Delay
#1). Maximum "04" for UL Commercial Burglary installations.
*13 BELL 1 SOUNDER DURATION [04] |
01-15 times 2 minutes. Minimum 16 minutes for UL
Commercial Burglary installations and minimum 6 minutes for
UL Commercial Fire installations
*16 BELL 1 CONFIRMATION OF ARMING DING [0]
1=enable; 0=disable.
Must be "1" for UL Commercial Burglary installations.
*22 KEYPAD PANIC ENABLES [001]
1=enable; 0=disable 995 996 999
*23 MULTIPLE ALARMS [1]
1=enable; 0=disable.
Must be 1 for UL Commercial Burglary installations.
*29 QUICK ARM [1]
1=enable; 0=disable
*32 PRIM. SUBS. ACCT # | | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
*38 PREVENT ZONE XXX BYPASS [000] | |
001-128; 000 if all zones can be bypassed
*39 ENABLE OPEN/CLOSE REPORT [1]
FOR INSTALLER CODE
1=enable; 0=disable
*84 SWINGER SUPPRESSION [03] |
01-15 alarms;
Must be "00" (disabled) for UL Commercial Burglary and
Commercial Fire installations.
*85 ENABLE DIALER REPORTS FOR PANICS & DURESS
1=enable; [0=disable]
995 996 999 Duress
*87 ENTRY WARNING [1]
1=continuous; 0=3 beeps
*88 BURG. ALARM COMM. DELAY [0]
1=16 seconds; 0=no delay.
Must be "0" for UL Commercial Burglary installations.
*90 SEC. SUBS. ACCT # | | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
2nd Page Fields
1*18 AFFECTS LOBBY [0]
Enter 1 if this partition affects the common lobby; enter 0 if it
does not.
Must be “0”for UL Commercial Burglary and Commercial
Fire installations.
1*19 ARMS LOBBY [0]
Enter 1 if arming this partition attempts to arm lobby; enter 0
if it does not
Must be “0”for UL Commercial Burglary and Commercial
Fire installations.
1*26 PANIC BUTTON OR SPEEDKEY
[00, 00, 00, 00] |
A
|
B
|
C
|
D
Enter speedkey macro # (01-35) to use keys A-C for macro.
Otherwise enter 00 to use as panic. For D key, enter macro
# or 00 to select macro when key is pressed.
1*43 PERM. KEYPAD BACKLIGHT [0]
1=enable; 0=disable When disabled, display lights when any
key is pressed, and turns off after period of keypad inactivity.
1*45 EXIT DELAY SOUNDING [0]
1=enable; 0=disable Produces quick beeping during exit
delay if enabled.

–11 –
1*47 CHIME ON BELL 1 [0]
1=enable; 0=disable
1*52 SEND CANCEL IF ALARM + OFF [0]
1=no restriction; 0=within Bell Timeout period only.
1*76 ACCESS CONTROL RELAY FOR PART.[00] |
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter 00-96; 00=none.
Must be "00" for UL Commercial Burglary and Commercial
Fire installations.
3rd Page Fields
2*05 AUTO-ARM DELAY [15] |
Enter the time between the end of the arming window and
the start of auto-arming warning period, in values of 1-14
times 4 minutes 00=instant; [15=no auto arm at all]. When
this delay expires, the Auto-Arm Warning Period begins.
2*06 AUTO-ARM WARNING PERIOD [15] |
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps every
15 seconds; "ALERT" displayed). Enter 01-15 minutes.
00=instant at end of arming delay.
2*07 AUTO-DISARM DELAY [15] |
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4 minutes;
00=instant at end of window; 15=no auto-disarm
2*08 ENABLE FORCE ARM FOR AUTO-ARM [0]
0=disable; 1=enable
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
1=enable; 0=disable If enabled, only openings and closings
occurring outside the scheduled opening/closing windows will
trigger dialer reports. Opening reports will also be
suppressed during the closing window, in order to prevent
false reports when the user arms the system and then re-
enters the premises to retrieve a forgotten item.
2*10 ALLOW DISARMING ONLY DURING [0]
ARMING/DISARMING WINDOWS
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installation.
0=disable; 1=enable
2*18 ENABLE GOTO FOR THIS PARTITION [0]
1=Allow log-on from other partitions; 0=disable
2*20 ENABLE J2 TRIGGERS BY PARTITION [1]
0=disable for displayed partition; 1=enable for displayed
partition
2*22 DISPLAY FIRE ALARMS OF [0]
OTHER PARTITIONS
0=disable; 1=enable
2*23 DISPLAY BURG/PANIC ALARMS OF [0]
OTHER PARTITIONS
0=disable; 1=enable
2*24 DISPLAY TROUBLES OF OTHER [0]
PARTITIONS
0=disable; 1=enable
4th Page Fields
3*57 BELL 2 & AUX RELAY CONFIRM [0,0]
ARMING DING Bell 2 Aux
0=disable; 1=enable. Must be “1”for UL Commercial
Burglary installations.
3*59 ENABLE BELL 2 & AUX RELAY [0,0]
CHIME ANNUNCIATION Bell 2 Aux
0=disable; 1=enable
3*60 BELL 2 & AUX RELAY TIMEOUT | |
Bell 2 Aux
Enter 00-15 times 2 minutes; 00=no timeout [00,00]
Minimum 16 minutes for UL Commercial Burglary
installations.
SUMMARY OF PROGRAMMING COMMANDS
•To enter program mode, enter installer code + [8] + [0] +
[0] + [0]
•To set standard defaults, press *97
•To change to next page of program fields, press *94
•To return to previous set of fields, press *99
•To erase account and phone number field entries,
press [*] + field number + [*]
•To assign zone descriptors, press #93 + follow menu
prompts
•To add custom words, press #93 + follow menu prompts
•To enter Installer's Message, press #93 + follow menu
prompts
•To exit program mode, enter *99 OR *98: *99 allows re-
access to programming mode by installer code. *98
prevents re-access to programming mode by installer
code.

–12 –
Programming With #93 Menu Mode
NOTE: The following field should be preset before beginning: 2*00 Number of Partitions. In addition, receivers should
be programmed via Device programming.
After programming all system related programming fields in the usual way, press #93 while still in programming mode to
display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (
YES) in response to the displayed menu
selection. Pressing 0 will display the next choice in sequence.
NOTE: All references in this manual for number of zones, user codes, partitions, VistaKey modules, the master
partition and the event log capacity, use the VISTA-128FB’s features. See page 2 for the table listing the differences
between the VISTA-32FB and the VISTA-128FB control panels. All other features are identical for both panels.
ULFor UL installations, verify that the audio alarm verification feature is disabled.
#93 MENU MODE KEY COMMANDS
The following is a list of commands used while in the menu mode.
#93 Enters Menu mode
[4] Serves as ENTER key. Press to have keypad accept entry.
[#] Backs up to previous screen.
0 Press to answer NO
1 Press to answer YES
001-009 All data entries are either 2-digit or 3-digit entries.
000 Exits menu mode, back into field programming mode, when entered at the first question for each category.
Menu selections are as follows:
PROMPT EXPLANATION
ZONE PROG?
1 = YES 0 = NO 0
For programming the following:
•Zone Number
•Zone Response Type
•Partition Number for Zone
•Dialer report code for zone
•Input Device Type for zone (whether RF, polling loop, etc.)
•Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system.
• Zone Attributes (e.g., Arm w/Fault, Silent, etc.)
EXPERT MODE?
1 = YES 0 = NO 0
Same as Zone Programming except:
• Done with a minimum number of keystrokes.
• Can program wireless keys using pre-defined templates.
NOTE: Be aware some of the zone attributes cannot be programmed in the Expert Mode. These can only be
done in Zone Programming.
REPORT CODE PROG?
1 = YES 0 = NO 0
For programming the following:
•Alarm report codes for zones
•Restore & supervisory codes
•All other system report codes
ALPHA PROG?
1 = YES 0 = NO 0
For entering alpha descriptors for the following:
•Zone Descriptors
•Installer's Message
•Custom Words
•Partition Descriptors
•Relay Descriptors
DEVICE PROG?
1 = YES 0 = NO 0
For defining the following device characteristics for addressable devices, including keypads, RF receivers
(5881), output relay modules (4204/4204CF), FSA modules, 4285/4286 VIP Module, ECP Long Range Radio
(7820), Panel Link module, and VISTA gateway module:
•Device Address
•Device Type
•Keypad Options (incl. partition assignment)
•RF House ID
•LRR Options (incl. programming radio)

–13 –
PROMPT EXPLANATION
OUTPUT PGM?
1 = YES 0 = NO 0
For defining output relay functions.
RLY VOICE DESCR?
1 = YES 0 = NO 0
For entering voice descriptors for relays to be used with the 4285/4286 VIP Module.
CUSTOM INDEX ?
1 = YES 0 = NO 0
For creating custom word substitutes for VIP Module annunciation.
ACCESS POINT PGM
1 = YES 0 = NO 0
For defining the parameters for each of the VistaKey access points, including which group(s) have access
through an access point (door). See the VistaKey-SK Installation and Setup Guide for the detailed
programming instructions.
ACCESS GRP PGM
1 = YES 0 = NO 0
For defining the capabilities (privileges) for each group of users. See the VistaKey-SK Installation and Setup
Guide for the detailed programming instructions.
EVENT/ACTION PGM
1 = YES 0 = NO 0
For defining events and time windows for an access group. See the VistaKey-SK Installation and Setup
Guide for the detailed programming instructions.
Zone Programming
If using 5800 Series transmitters, do not the install bat
teries until you are ready to enroll them. After enrolling
the transmitter, the battery need not be removed. This is to prevent enrolling the wrong serial number.
PROMPT EXPLANATION
ZONE PROG?
1 = YES 0 = NO 0
Press 1to enter ZONE PROGRAMMING mode. The following screens appear. Press [✱] to display the next
screen. Press # to display a previous screen.
SET TO CONFIRM?
1 = YES 0 = NO 0
This prompt appears once upon entering Zone Programming Mode.
If “Yes,”Confirmation prompts will be displayed after the device’s Serial and Loop numbers have been
entered later.
ENTER ZONE NO.
000 = QUIT 010 
Zone 010 entered ↑
Enter the 3-digit zone number to be programmed, as follows:
Protection Zones = 001–128
Relay Zones = 601–632
ECP Device Supervisory Zones = 800–830
System Supervisory Zones = 988, 990, 992 (duress), 997
Keypad Panic Zones = 995, 996, 999
Press [✱] to continue.
010 ZT P RC In L
00 1 10 00 1
This display appears, showing a summary of the zone's current programming. ZT = Zone Type, P=
Partition, RC = Report Code, In = the input type of device, and L= the device's loop number to which the
sensor is connected.
Some devices can support more than one zone by means of individual loops (for example, 5801, 5804,
5816, 5817, etc.). If the zone is not programmed, the display appears as shown here. If you are checking a
zone's programming, and it is programmed satisfactorily, press [#] to back up one step and enter another
zone number, if desired.
Press [✱] to continue.

–14 –
PROMPT EXPLANATION
Each zone must be assigned a zone type, which defines the way in which the system responds to faults in
that zone. Refer to the Zone Type Definitions section in the VISTA-32FB/VISTA-128FB Installation and
Setup Guide for detailed definitions of each zone type. Enter the zone type desired (or change it, if
necessary). Available zone types are listed below.
00 = Assign for Unused Zones 16 = Fire With Verification
01 = Entry/Exit #1, Burglary 17 = Waterflow
02 = Entry/Exit #2, Burglary 18 = Fire Supervisory
03 = Perimeter, Burglary 19 = 24-Hour Trouble
04 = Interior Follower, Burglary 20 = Arm–STAY†
05 = Trouble Day/Alarm Night 21 = Arm AWAY†
06 = 24 Hr. Silent Alarm 22 = Disarm†
07 = 24 Hr. Audible Alarm 23 = No Alarm Response (e.g., relay activation)
08 = 24 Hr. Auxiliary 27 = Access Point
09 = Fire Without Verification 28 = MLB Supervision (if VGM installed)
10 = Interior Delay, Burglary 29 = Momentary Exit (used with VistaKey module)
010 ZONE TYPE
PERIMETER 03
Zone number 010 and
Zone Type 03 entry shown
†These are special zone
types used with 5800
Series Wireless
Pushbutton Units that
result in arming the system
in the STAY or AWAY
mode, or disarming the
system, depending on the
selection made.
Press [✱] to continue.
010 Partition
1
Enter the partition number (1–8) you are assigning this zone to.
Press [✱] to continue.
010 REPORT CODE
1st 03 2nd 12 3C
Enter the report code. The report code consists of 2 hexadecimal digits, each in turn consisting of 2
numerical digits. For example, for a report code of "3C," enter 03 for "3" and 12 for "C."
(Refer to the System Communication section in the Installation and Setup Guide for more information about
report codes and reporting formats.)
Press [✱] to continue.
010 INPUT TYPE
RF Xmitter 3
Input types 4 & 5 are
valid for certain 5800
Series transmitters only
(e.g., 5801, 5802, 5802CP
& 5803).
If using input type 02
with a door/window type
transmitter, only loop 1
may be used.
Input type 10 is
applicable only if
PassPoint ACS is
installed with the VISTA
Gateway Module.
If you selected response
type 14, 28, or 29 the
input type MUST be 00.
Enter the input device type as follows:
00 = not used
01 = hardwired
03 = supervised RF transmitter (RF type)
04 = unsupervised RF transmitter (UR type)
05 = RF button-type transmitter (BR type)
06 = serial number polling loop device (SL type)
07 = DIP switch-type polling loop device
08 = right loop of DIP switch type device
09 = keypad input (code + #73)
10 = PassPoint ACS input
11 = VistaKey Door Status Monitor (DM)
12 = VistaKey Request to Exit (RE)
13 = VistaKey General Purpose (GP)
Right loops refer to the use of the right loop on a 4190WH Zone Expander Module and/or 4278 PIR, which
allow hardwired devices to be monitored by the polling loop.
If you are programming hardwired or DIP switch polling loop devices, the summary display appears after
completing this entry.
NOTE: Input types 11 (DM), 12 (RE), and 13 (GP) should only be used with VistaKey modules.
Press [✱] to continue.
010 ACCESS POINT
(00-31) 01
If response type 27, or 29 was selected, this prompt will be displayed. Enter the access point to be
controlled by the response type (00-31 for type 27; 01-15 for type 29).
Note: If you are using the VistaKey module, the access point must match the address that was set in the
module.
Press [✱] to continue.
010 ENTRY OR EXIT
0
If response type 27 selected, or 29 was selected, this prompt will be displayed. Enter whether the access
point is an entry or exit point.
0= entry; 1= exit
Press [✱] to continue.

–15 –
PROMPT EXPLANATION
010 BELL/RLY SEL
0
Each zone can be assigned to activate either one or both Notification Appliance Circuits and/or the system’s
auxiliary relay. Enter one of the following assignments:
0=none; 1=bell 1; 2=bell 2; 3=bell 1 & bell 2; 4=aux relay; 5=bell 1 & aux relay; 6=bell 2 & aux relay; 7=bell 1
& bell 2 & aux relay.
Press [✱] to continue.
010 SMART CONTACT
1 = YES 0 = NO
If input type 3 or 6 was selected, this prompt will be displayed. Enter 1for devices that monitor maintenance
signals (ex. 5192SD, 5192SDT, 5808) or can be used to limit fault signals in the disarmed state (ex. Quest
2260SN). Otherwise, enter 0.
NOTE: The Smart Contact option must ONLY be selected for devices that support the feature, otherwise
unpredictable results may occur.
010 V-PLEX RELAY?
1 = YES 0 = NO
If you selected input type 6, this prompt displays. Enter 1if using a 4101SN Relay Module for this zone.
Otherwise enter 0.
Press [✱] to continue.
010 CONS ECP ADDR
(00-30) 01
If you selected input type 09, this prompt displays. Enter the ECP address of the keypad that is being used
for entry/exit for this access point (00-30).
Press [✱] to continue.
010 ACS ZONE #
(00-31) 01
If you selected input type 10, this prompt displays. Enter the PassPoint ACS zone ID that this VISTA zone
maps to (00-31).
Press [✱] to continue.
010 INPUT S/N: L
AXXX-XXXX 1
For Serial Number entry and Loop Number entry, do one of the following:
a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and
release the button, wait approximately 4 seconds, then press and release the button a second time.
OR
b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the Alpha keypad.
Then press the [✱] key, the cursor moves to the “L”position. You can edit the loop number, if necessary.
When the loop number is acceptable, press [✱].
OR
c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several
input loops).
Press [✱] to accept.
010 INPUT S/N: L
A022-4064 1
The cursor will then move to the Loop column (L) with the previously entered/transmitted serial number
displayed.
Enter the loop number (refer to 5800 Series Transmitters Loop Designations below).
To Delete an Existing Serial Number, enter “0“in the loop number field. The serial number will change to
“0”s.
If “0”was entered in error, simply re-enter the loop number or press [#], and the serial number will return to
the display.
Press [✱] to accept.
010 INPUT S/N: L
A022-4064 1
The system will then check for a duplicate serial/loop number combination.
If a duplicate serial/loop number combination is found, the keypad will emit a single long beep, and display
the serial number along with a “?”for the loop number, allowing you to re-enter the correct loop number.
If the serial/loop number combination is not a duplicate in the system, a display appears showing the serial
number and loop number entry.
Press [✱] to continue.

–16 –
5800 Series Transmitters Loop Designations
LOOP
1
5802MN
ENROLL AS "UR" OR "RF"
YOU MUST
ENROLL THIS
BUTTON
LOOP 3
LOOP 1
LOOP 2
LOOP 4
LOOP
1
5808
ENROLL AS "RF"
5804
ENROLL
AS "BR"
5817
ENROLL AS "RF"
LOOP 1
(PRIMARY)
LOOP 2
(AUX. CENTER)
LOOP 3
(AUX. RIGHT)
LOOP 1
(MOTION)
5890
ENROLL AS "RF"
5816
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 1
(TERMINALS)
5827
SET HOUSE CODE 5827BD
SET HOUSE CODE
5816MN
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 1
(TERMINALS)
5819
ENROLL AS "RF"
LOOP
2
(REED)
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
LOOP 3
(TERMINALS)
5819S (WHS & BRS)
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 1
(INTERNAL
SHOCK
SENSOR)
LOOP 3
(TERMINALS)
5850 (GBD)
ENROLL AS "RF"
(Green)
(Red)
(Yellow)
5804BD
ENROLL AS "BR"
LOOP 3
LOOP 1
LOOP 2
LOOP 4
SET
HOUSE
CODE
YOU MUST
ENROLL THIS
BUTTON
LOOP
1
5809
ENROLL AS "RF"
5801
ENROLL AS "UR" OR "RF"
LOOP 3
LOOP 1
LOOP 2
LOOP 4
YOU MUST
ENROLL THIS
BUTTON
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•••
5800_trans_loop-V0
Note: For information on any transmitter not shown above, refer to the instructions accompanying that transmitter for details
regarding loop numbers, etc.
UL
The 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, 5827BD,
and 5850 transmitters are not intended for use in UL installations.
PROMPT EXPLANATION
XMIT TO CONFIRM
PRESS ✱TO SKIP
Confirmation Option: This prompt only appears if you answered “Yes”at the first prompt. The system
enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate
the loop input or button that corresponds to this zone. At any time during this step, you may press the [✱] key
on the keypad to save the serial and loop number combination without confirming.
Entd A022-4063 1
Rcvd A022-4064
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it is also displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key twice and then enter or transmit the correct serial number.
010 ZT P RC In L
03 1 3C RF 1s
If the serial number transmitted does match the serial number entered, the system beeps 3 times and a
summary display appears, showing that zone’s programming. Note that an “s”indicates that a transmitter’s
serial number has been enrolled.
Press [✱] to accept the zone information.

–17 –
PROMPT EXPLANATION
ENTER ZONE NO.
000 = QUIT 011
The system now returns to the “ENTER ZONE NO.”prompt for the next zone.
When all zones have been programmed, enter “000”to quit.
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
When you have finished programming all zones, test each using the system’s Test Mode. Do not use the
Transmitter ID Sniffer Mode. The system checks only for transmission of one zone on a particular
transmitter, NOT the zones assigned to each additional loop, and also does not verify polling loop type
zones.
Expert Mode Zone Programming
Expert mode allows you to program zones using the minimum number of screens and keystrokes.
Expert Mode Zone Programming does not provide the capability to program some of the zone’s attributes,
such as Arm w/Fault, Vent Zone, STAY mode, Auto-STAY, Bypass Group, etc. If you want to program a
zone for any of these attributes, you must use Zone Programming.
Enter the Programming mode with [Installer Code] + 8 0 0 0
Before programming your zones, do the following:
1. Program field 2✱00: Number of Partitions.
2. Enable your RF Receiver in Device Programming menu mode.
To program your zones, press ✱93 to display the "ZONE PROG?" prompt. Enter “0”(NO) to each prompt until the “EXPERT
MODE?”prompt appears.
PROMPT EXPLANATION
EXPERT MODE?
1 = YES 0 = NO 0
Press 1to enter Expert mode.
SET TO CONFIRM?
0 = NO 1 = YES 0
This prompt appears once upon entering Expert Mode.
If you select “Yes,”Confirmation prompts will be displayed after the device’s Serial and Loop numbers have
been entered later.
Zn ZT P RC In L
001 03 1 10 HW -
A summary display appears, showing zone 1’s current programming or default values.
Zn ZT P RC In L
010 03 1 10 RF 1s
Enter the desired 3-digit zone number and press [✱].
Note: If you want to exit the Expert mode, enter “000”+ [✱].
If an “s”appears after the loop number, it indicates that the transmitter’s serial number has been enrolled.
Use the [D] key to enter and duplicate wireless keys (see “Entering Wireless Keys”later)

–18 –
PROMPT EXPLANATION
Zn ZT P RC In L
010 03 1 10 RF -
Enter all zone information except for Loop number, or press “C”to copy the zone information on this screen
from the last saved zone (including Loop).
ZT = Zone Type
P = Partition
RC = Report Code
In = Input Device Type
L = Loop number to which the sensor is connected.
NOTE: Pressing the [C] copies the zone information from the last saved zone, which includes the
input type. Verify this information is correct for this zone.
On this screen:
• Use the [A] key to move to the right.
• Use the [B] key to move to left and to back up to “ZT”field.
Press [✱] to accept the existing or newly-entered zone information.
ZN B M V A C E AD
010 2 1 1 0 1 1 01
Enter the remainder of the zone’s information, or press the [C] key to copy the zone attributes on this screen
from the last saved zone.
B = Bell/Relay Assignment
M = Maintenance (only used if “In”= 3 or 6)
V = V-plex Relay? (only used if “In”= 6)
AC = Access Point (only used if ZT = 27, 29 or In = 6, 11, 12, 13)
E = Entry or Exit? (only used if ZT = 27)
AD = Address (only used if “In”= 9 or 10)
If “In”= 9, enter the Device Address
If “In”= 10, enter the PassPoint Zone Number
NOTE: Pressing the [C] copies the zone attributes from the last saved zone. Verify the attributes for
this zone are correct.
On this screen:
• Use the [A] key to move to the right.
• Use the [B] key to move to left and to back up to “V”field.
Press [✱] to accept existing information.
010 INPUT S/N: L
A XXX-XXXX  -
If you entered RF, BR, UR or SL for the Input Type, this screen displays. Otherwise the summary screen for
the next zone displays.
Enter the 7-digit serial number, using one of the following methods:
a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and
release the button, wait approximately 4 seconds, then press and release the button a second time.
OR
b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the alpha keypad.
Then press the [✱] key, the cursor will move to the “L”position. You can edit the loop number, if
necessary. When the loop number is acceptable, press [✱].
OR
c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several
input loops).
Remember, you can use the [A] key to move to the right or the [B] key to move to the left.
You can also use the [#] key to back up without saving.
010 INPUT S/N: L
A022-4064 1
Press [✱] to accept the serial number and advance to the “L”position (if method “a”or “c”was used), then
enter the loop number.
If necessary, press the [#] key to back up without saving, and re-enter or edit the serial number before
pressing [✱] to save
The system checks for a duplicate. If a duplicate serial/loop number combination is found, the keypad will
emit a single long beep, and display the serial number along with a “?”for the loop number, allowing you to
re-enter the correct loop number.
010 INPUT S/N: L
A000-0000 1
To Delete an Existing Serial Number, enter “0“in the loop number field. The serial number will change to
“0”s.
If “0”was entered in error, simply re-enter the loop number or press [#], and the serial number will return to
the display.

–19 –
PROMPT EXPLANATION
XMIT TO CONFIRM
PRESS ✱TO SKIP
The prompt to confirm appears. This prompt only appears if you answered “Yes”at the “SET TO
CONFIRM?”prompt.
The system enters a confirmation mode so that the operation of the actual programmed input can be
confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you
may press the [✱] key on the keypad to save the serial and loop number combination without confirming.
Entd A022-4063 1
Rcvd A022-4064
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it also is displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display for the next zone does not appear), press the [#] key twice and then enter or transmit the correct
serial number.
Activate the button on the wireless key again after re-entering the serial number.
Zn ZT P RC In L
011 00 1 10 00 1
If the serial number transmitted matches the serial number entered, the system beeps 3 times and
advances to the summary display for the next zone's programming.
After all the zones have been programmed, enter 000 for the zone number to quit.
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
Entering Wireless Keys
If you pressed the D key previously to enter defaults for 5804 and/or 5804BD wireless keys, the following screens appear:
PROMPT EXPLANATION
FROM TEMPLATE
1–6 1
Enter template number (1–6).
1–3 = 5804 templates; 4–6 = 5804BD templates. See the defaults provided for each template in the chart
that follows these procedures.
Select from templates. Press [✱] to display template (template 1 shown selected).
Note: If necessary, press [#] to back up and re-enter template number.
Press [#] if you want to return to zone attributes screen.
L 01 02 03 04
ZT 23 22 21 23 1
When you press [✱], the selected template is displayed.
Top line of display represents loop numbers; bottom line represents zone type.
Press [✱] to accept template.
PARTITION
1
Enter partition number for wireless key.
Press [✱] to continue.
ENTER ZONE NO
000 = QUIT 024
▲
Example of zone number
suggested by the system.
This indicates that zones
24, 25, 26, and 27 are
available.
The system searches for the highest available, consecutive 4-zone group (the four zones required for the
5804 and 5804BD), and displays the lowest zone number of the group.
If you want to start at a different zone number, enter the zone desired and press [✱].
If that zone number is displayed, the system has the required number of consecutive zones available,
beginning with the zone you entered. If not, the system again displays a suggested zone that can be used.
If the required number of consecutive zones is not available at all, the system will display “000.”
Press [✱] to accept.
024 INPUT S/N L
AXXX-XXXX 1
To enter the serial number:
Press and release a button on the wireless key.
OR
Manually enter the 7-digit serial number printed on the device’s label.
Press [✱] to accept serial number. The system checks for a duplicate.
If a duplicate exists, a long error beep will sound and the serial number reverts back to all “X”s allowing
you to re-enter the serial number.
Use the [A] key to move forward within the screen, and the [B] key to back up.

–20 –
PROMPT EXPLANATION
XMIT TO CONFIRM
PRESS ✱TO SKIP
If you entered YES previously at the SET TO CONFIRM prompt (see first prompt following entry into the
Expert Programming Mode), the display on the left appears.
To confirm, activate the button on the wireless key that corresponds to this zone.
Entd A022-4063
Rcvd A022-4064
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key and then enter the correct serial number.
Activate the button on the wireless key again after re-entering the serial number.
ENTER ZONE NO
000 = QUIT 028
If the serial number transmitted matches the serial number entered, the system will beep 3 times and
revert to the "Start Zone No." prompt and will show the lowest numbered zone of the next available 4-zone
group (4 consecutive zones) that is available for programming.
After all the wireless keys have been entered, enter 000 for the zone number to quit.
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
Wireless Key Default Templates
5804 5804BD
Template 1 Loop Function Zone Type Template 4 Loop Function Zone Type
1 No Response 23 1 No Response 23
2 Disarming 22 2 No Response 23
3 Arm AWAY 21 3 Arm AWAY 21
4 No Response 23 4 Disarming 22
Template 2 Loop Function Zone Type Template 5 Loop Function Zone Type
1 No Response 23 1 No Response 23
2 Disarming 22 2 Arm STAY 20
3 Arm AWAY 21 3 Arm AWAY 21
4 Arm STAY 20 4 Disarming 22
Template 3 Loop Function Zone Type Template 6 Loop Function Zone Type
1 24-Hour Panic 07 1 24-Hour Panic 07
2 Disarming 22 2 Arm STAY 20
3 Arm AWAY 21 3 Arm AWAY 21
4 Arm STAY 20 4 Disarming 22