Honeywell V4000 User manual

QuickStart INSTALLATION GUIDE
Unpack the Contents
Make sure you have all the parts shown here. If any parts are missing, contact Honeywell.
For more detailed instructions please refer to the
printed manual included in the package.
V4000
START HERE
V4000
Installation
Manual
V4000
V4000
Installation
Manual
1
www.honeywell.com
It is strongly recommended that you follow
these step-by-step numbered instructions to
set up the V4000.
Additional and Optional Equipment Needed for Installation
2
12V, 1A Power Supply
(ADEMCO AD12612
or equivalent)
One to Four Cameras
with BNC Connections
Color or Black and White
Vista
Alarm Control
Panel
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
Wiring the V4000
3
Contacts
( i.e. Motion Sensor
or Door Contact )
Keypad
(ECP)Bus
Telephone
Line
NTSC/PAL Video Input
(BNC Connectors)
V4000
RS 232
DB-9 Male
Connector
+
12 VDC
4 x 75
Termination
Dip Switch
Ω
RED GRNRED BLK
YEL
GRN
Telephone
Line
See Appendix B
for connection to
Cellphone
See Appendix A
for direct connection
to PC/Laptop
Vista
Alarm Control
Panel
Power Supply
Control
Center
Software
Keybus
RED LED (status)
GRN LED (power on)
Incoming
Telephone
Line
Tip Ring
Ring
Ring Tip
Tip
Handset
Side
AC
IN
+
_
1361
XFMR
16.5VAC
DC
OUT
+_
RED
BLACK
POWER SUPPLY
BACKUP
BATTERY 12VDC
12 VDC
ADEMCO AD12612
or Equivalent
BLK
YEL
GRN
RED
Control Center Application
Installer and User CDs

5
Connect with Central Station
6
Contact your central station account manager (if central station is not
OzVision Compatible, please have them contact OzVision).
Follow these steps to add video services such as visual verification,
video open/close reports and OzMail notification.
Inform the central station what services will be used.
Provide the central station with the telephone number of the unit, as well
as which sensor is associated with each camera.
The Control Center Application allows
your customer to dial-in to the V4000 unit
and view live video. Confirm that the
computer meets the minimum hardware
requirements and follow the on-screen
instructions. This software may be installed
on multiple computers by your customer.
Provide the central station with the buffer parameters (length of the
pre and post alarm) for the video event.
Send signals from each zone to the central station to verify that
signals are being properly received.
Connect Telephone Line
Honeywell’s
Control Center
Application
for End Users
CD
Install the Software (OPTIONAL)
7
Contact Information
For specific questions and additional information, please contact Honeywell's
Alarmnet Technical Support Group at 1-800-222-6525.
A standard modem connection is required
for the computer on which the software is to
be installed.
DSL and Cable modem connections are
currently not supported.
Please Note:
4
a
b
c
d
e
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
1
.
3
6
m
m
-
2
.
5
m
m
V
A
R
I
A
B
L
E
F
O
C
U
S
Video Input
Connected to
camera via
BNC
Connection
NTSC/PAL Video Cameras
NTSC/PAL Video Input
V4000
RS 232
DB-9 Male
Connector
+
12 VDC
4 x 75
Termination
Dip Switch
Ω
Telephone
Line
Keybus
RED LED (status)
GRN LED (power on)
Connect Video Cameras and
Power Supply
Power Supply
AC
IN
+
_
1361
XFMR
16.5VAC
DC
OUT
+_
RED
BLACK
POWER SUPPLY
BACKUP
BATTERY 12VDC
12 VDC
ADEMCO AD12612
or Equivalent
Keypad
(ECP)Bus
Telephone
Line
NTSC/PAL Video Input
(BNC Connectors)
V4000
RS 232
DB-9 Male
Connector
+
12 VDC
4 x 75
Termination
Dip Switch
Ω
RED GRN
Telephone
Line
Vista
Alarm Control
Panel
Keybus
RED LED (status)
GRN LED (power on)
Incoming
Telephone
Line
Handset
Side BLK
YEL
Ring Tip
Green
Red
Ring Tip
Ring Tip
V4KQS62505: Rev. 1