Honeywell Ademco Vista-12D Assembly instructions

K10022V1 4/05 Rev. A
A
AD DE EM MC CO O V Vi is st ta a- -1 12 2D D
Installation and Set-Up Guide
This control complies with EN50131-1

Installation and Setup Guide
ii

iii
Table Of Contents
•••••••••••••••••••••••••••••••••
Features and Installation Highlights ................................................................................................. 1-1
Capabilities ........................................................................................................................................... 1-1
Functions............................................................................................................................................... 1-1
Compatible Devices............................................................................................................................... 1-2
Important Installation Highlights (Installer Please Read) ................................................................ 1-3
Mounting and Wiring the Control....................................................................................................... 2-1
Cabinet and Lock .................................................................................................................................. 2-1
Mounting the PC Board........................................................................................................................ 2-1
Wiring to Keypads ................................................................................................................................ 2-3
Sounder (Siren) Connections................................................................................................................ 2-4
Wiring the AC Transformer ................................................................................................................. 2-5
Backup Battery ..................................................................................................................................... 2-6
Earth Ground ........................................................................................................................................ 2-6
Basic Wired Zones................................................................................................................................. 2-7
Smoke Detectors ................................................................................................................................... 2-8
4219/4229 Expansion Zones ................................................................................................................. 2-9
6164 Keypad Expansion Zones........................................................................................................... 2-10
Installing the RF Receiver.................................................................................................................. 2-11
Installing a 5800TM Module .............................................................................................................. 2-11
Installing the Transmitters................................................................................................................ 2-12
Installing a Keyswitch ........................................................................................................................ 2-12
Connecting Relay Modules ................................................................................................................. 2-14
Powerline Carrier Devices.................................................................................................................. 2-16
On-Board Triggers .............................................................................................................................. 2-17
Phone Line Connections ..................................................................................................................... 2-18
Alternative Communications Media (ACM) Connections ................................................................. 2-18
Audio Alarm Verification Connections (AAV, “Listen-In”) ............................................................... 2-18
Programming Overview ........................................................................................................................ 3-1
About Programming.............................................................................................................................. 3-1
Zones and Partitions............................................................................................................................. 3-2
Keypads ................................................................................................................................................. 3-2
Wireless Receiver Transmitters, and Wireless Keys (keyfobs)........................................................... 3-3
Pager Programming.............................................................................................................................. 3-3
Function Keys ....................................................................................................................................... 3-4
Output Devices...................................................................................................................................... 3-4
Zone Type Definitions........................................................................................................................... 3-4
Mechanics of Programming .................................................................................................................. 3-8
Data Field Programming....................................................................................................................... 4-1
About Data Field Programming........................................................................................................... 4-1
Programming Data Fields .................................................................................................................... 4-1
System Setup Fields ............................................................................................................................. 4-1
Zone Sounds & Timing ......................................................................................................................... 4-3
Dialer Programming (∗40 – ∗50) .......................................................................................................... 4-4
System Status Report Codes ................................................................................................................ 4-7

Installation and Setup Guide
iv
Miscellaneous System Fields................................................................................................................ 4-9
Pager Programming Fields................................................................................................................. 4-14
Miscellaneous System Fields.............................................................................................................. 4-15
AUI Enable.......................................................................................................................................... 4-18
Keypad Programming Fields.............................................................................................................. 4-19
Menu Mode Programming..................................................................................................................... 5-1
About Zone Programming (∗56 and ∗58 Menu Modes) ....................................................................... 5-1
∗56 Zone Programming Procedure ....................................................................................................... 5-1
Completing Zone Programming ........................................................................................................... 5-7
∗58 Expert Programming Mode Procedures ........................................................................................ 5-7
Wireless Key Programming Templates ............................................................................................. 5-10
About Output Device Programming (*79/*80 Menu Mode) .............................................................. 5-13
*79 Menu Mode: Output Device Mapping ......................................................................................... 5-13
*80 Menu Mode: Defining Output Functions .................................................................................... 5-15
About Zone Lists (∗81 Menu Mode).................................................................................................... 5-18
Zone List Programming...................................................................................................................... 5-18
About Function Key Programming (∗57 Menu Mode)....................................................................... 5-20
Programming Function Keys ............................................................................................................. 5-20
About Descriptor Programming (*82 Menu Mode)............................................................................ 5-22
Configurable Zone Type Programming (*83 Menu Mode) ................................................................ 5-24
Programming Installer and User Schedules ..................................................................................... 5-26
System Communication and Operation.............................................................................................6-1
Panel Communication with Central Station ....................................................................................... 6-1
Report Code Formats ............................................................................................................................ 6-1
Robofon 8 Format.................................................................................................................................. 6-3
ADEMCO Contact ID®......................................................................................................................... 6-4
Security Codes....................................................................................................................................... 6-6
Keypad Functions ................................................................................................................................. 6-7
Panic Keys............................................................................................................................................. 6-9
Follow-Me Feature................................................................................................................................ 6-9
Setting/Adjusting the Real-Time Clock ............................................................................................. 6-10
Various System Trouble Displays ...................................................................................................... 6-11
Testing the System.................................................................................................................................. 7-1
About Test Procedures.......................................................................................................................... 7-1
System Test........................................................................................................................................... 7-1
Go/No Go Test Mode ............................................................................................................................. 7-2
Dialer Communication Test ................................................................................................................. 7-3
Automatic Standby Battery Tests........................................................................................................ 7-3
Specifications & Accessories ................................................................................................................ 8-1
SECURITY CONTROL......................................................................................................................... 8-1
COMPATIBLE DEVICES .................................................................................................................... 8-2
5800 Series Transmitter Input Loop Identification ............................................................................ 8-3
Limitations and Warranty..................................................................................................................... 9-1
Index...................................................................................................................................Index-1

1-1
SECTION 1
Features and Installation Highlights
•••••••••••••••••••••••••••••••••
Capabilities
•Supports 2 independent partitions, which can protect two independent areas, as if each
area had its own control.
•Supports 1 common area partition that allows either of the other two independent
partitions to arm, while leaving a common area (ex. lobby or foyer) disarmed for access
into the remaining disarmed partition.
•Supports up to 22 protection zones plus 16 keyfob zones (zones 49-64) for total of 38
zones:
-- 6 basic wired zones (zones 1-6) with optional zone-doubling/double-balanced zone
feature
-- Up to 8 additional wired zones (zones 17-24) using an 8-zone 4219/4229 module.
-- Supports up to 16 wireless transmitter zones (5800 series; zones 9-24).
-- Supports up to 4 installer-configurable zone types
•Up to 16 User Level Security Codes, each with separate authority levels and partition
access
Downloading: Via an IBM compatible computer, Compass downloading software, and an
ADEMCO CIA/CIA-EU modem.
Functions
•Single-button arming feature: Can use dedicated keys to arm the system AWAY or
STAY
•Up to 8 Schedules, to control output devices, to determine when users have access,
and/or to auto-arm/disarm (or allow disarm) the system
•Up to 2 Keypad macros, which can be activated by wired/wireless keypads
•Paging feature allows certain system conditions to be reported to up to 2 pager phone
numbers; can use a dedicated key on keypads to send a signal to a pager
•User programmable telephone number for audio “beeps” reporting of alarms to the user
(follow-me feature).
•Built-in Telephone Line Monitoring option can monitor the telephone line voltage and
can cause a local display, or a display and trouble/alarm sound.
•Event Logging records up to 254 selected events in a history log; control and readout
from the log is done via ADEMCO Compass Downloader software or using an
installer/master code at an alpha display keypad for local display.
•Installer-customized zone descriptors for all zones (useful only when using alpha display
keypads).

Installation and Setup Guide
1-2
•Optional siren supervision detects external sounder wiring short or open; causes a
trouble condition, keypad display, and sends a report to the central monitoring station,
if enabled.
•Optional RF jam detection for wireless systems detects a condition that may impede
proper RF reception (i.e., jamming or other RF interference); causes keypad display,
sends a report to the central monitoring station (if trouble reporting is enabled), and can
optionally send a tamper alarm if detected during the armed mode.
•Individual user code selection for open/close reporting to central monitoring station (set
when adding a user code, attribute 6).
Compatible Devices
•Supports up to 8 Addressable Keypads: 6148/6150 Fixed-Word Display Keypads, 6164
Alpha Keypad, 6128RF/6128RFH/6150RF/6160RF Keypad/Transceivers, 6160V Voice
Keypad
•Supports a 4219 or 4229 addressable basic wired zone expander module
•Supports 5881/5882EU/5882EUH/5883 series receiver and 5800/5800EU/5800H/5800AP
series transmitters
•Outputs up to 4 relays, two on-board triggers, and/or Powerline Carrier Devices (X-10
type)
-- Use any combination of 4204, 4229, 6164 relays and/or Powerline Carrier Devices.
-- Output functions (up to 12)
•Alarm power output provides a 12VDC, 2 AMP output that can drive compatible
sounders with a steady output for burglary/panic, or temporal pulse (3 pulses – pause –
3 pulses – pause – 3 pulses. . .) for fire. Uses current limiting circuitry for protection.
•Auxiliary Power Output: 12VDC, 600 mA maximum (uses fuse for protection).
•Backup Battery: Rechargeable (sealed lead-acid type) 12VDC, 6AH minimum.
•Audio Alarm Verification (using AAV module, such as ADEMCO UVS); can be used in
conjunction with an output trigger to permit voice dialog between an operator at the
central station and a person at the premises.
•Alternative Communication Media: Primary telephone number messages can be
reported via ECP connection to Ethernet TCP-IP Internet
•AC Power Supply: Wired-in or Plug-in 110 (e.g. 1321)/220VAC transformer

Features and Installation Highlights
1-3
Important Installation Highlights (Installer Please Read)
•This system uses addressable keypads and a Zone Expander Module (see table of
addresses in Programming Overview section).
•Keypads must be set for addresses 16-23 (first keypad is address 16, which is different
from previous controls) and programmed in data fields *190-*196.
•Zone Expander Module must be set for specific address (08), based on the zone numbers
used
(see table of addresses in 4219/4229 Expansion Zones section).
•4204 Relay Module must be set for specific address (13; see Connecting Relay
Modules section).
•6164 Keypads must be set for two addresses: a keypad address and a zone expander
address (if using the keypad’s expansion zones).
•This control will not power-up unless AC mains is connected (will not power-up on
battery alone). However, once the system is powered up, it will operate on battery power
in the event of AC mains loss.
•Relays have two programming menu modes: Use *79 Menu mode to map module
addresses and device (output) numbers. Use *80 Menu mode to define the output
functions (see Output Device Programming section).
•This system supports programmable function keys. Use *57 Menu mode to define the
function keys (see Function Key Programming section).
•This system provides various paging features. Refer to the Programming Overview
section for a summary on pager programming.

Installation and Setup Guide
1-4

2-1
SECTION 2
Mounting and Wiring the Control
•••••••••••••••••••••••••••••••••
This section describes the procedures for mounting and wiring this control and its peripheral
devices. In the following subsections, procedures are listed in the left column, while notes
and pertinent explanations are provided in the right column.
Mounting the PC Board
NOTE: The door of the metal cabinet may be
removed to make it easier to install the PC
board. Remove the door as follows:
1. With the cabinet laying on a flat surface,
swing open the door to its full-open position.
2. Slide the door out of its retaining slots in
the cabinet and store in a safe place.
3. Remove standoff (part number K0380) from
the hardware bag and insert it into the
square hole in the back of the cabinet so
that it will align behind the lower left
mounting hole in the PC board.
4. Insert top of circuit board into slots at top of
cabinet. Make sure that circuit board rests in
slots as indicated in the diagram shown below.
5. Swing base of circuit board onto the raised
cabinet tab and standoff.
6. Secure the sides of the PC board to the
enclosure using the 2 screws provided.
Notes
•Before installing the cabinet's contents, remove
the metal cabinet knockouts required for wiring
entry. Do not remove the knockouts after the
circuit board has been installed.
Cabinet and Lock
1. Mount the control cabinet to a sturdy wall
in a clean, dry area, which is not readily
accessible to the general public, using
fasteners or anchors (not supplied) with the
four cabinet mounting holes.
2. Remove cabinet door, then remove the lock
knockout from the door. Insert the key into
the lock.
3. Position the lock in the hole, making
certain that the latch will make contact
with the latch bracket when the door is
closed. When correctly positioned, push the
lock until it is held securely by its snap
tabs.
Notes
•The cabinet can be closed and secured without a
lock by using 2 screws in the cover's edge.
CABINET DOOR
BOTTOM
LOCKED
UNLOCKED
cab_lock_snap-001-V0
ADEMCO ADEMCO
PUSH
SNAP
TAB
SNAP
TAB
PUSH
ON LOCK
UNTIL IT
IS SEATED
SECURELY
STEP 2STEP 1
CHECK
POSITION
Figure 1. Installing the Cabinet Lock

Installation and Setup Guide
2-2
V12D-001-V0
1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 21 22 23 25
Figure 2. Mounting the PC Board

Mounting and Wiring the Control
2-3
Wiring to Keypads
1. Connect keypads to the control’s keypad
terminals as shown on the Summary of
Connections diagram.
Determine wire size using the Wiring Run
Chart below.
2. Set keypad addresses. Refer to the address
setting instructions included with the
keypads and set each keypad device
address according to the chart at right.
3. Program the keypad addresses, partition
assignments and sound options in data
fields *190-*196.
NOTE: Each keypad must be assigned a
unique address, starting at address 16.
Keypads programmed with the same
address will give unpredictable results.
Supplementary Power (optional)
1. Connect as shown. Be sure to connect the
negative (–) terminal on the power supply
unit to terminal 4
(AUX –) on the control.
+–
+
456 7
SUPPLEMENTARY
POWER SUPPLY
–
CONTROL TERMINAL STRIP
AUX. AUX. DATA
IN
DATA
OUT
IMPORTANT:
MAKE THESE
CONNECTIONS
DIRECTLY TO
SCREW
TERMINALS AS
SHOWN.
TO KEYPAD RED POWER WIRE (V+)
TO KEYPAD BLK GROUND WIRE (V-) TO KEYPAD YEL DATA WIRE (<) TO KEYPAD GRN DATA WIRE (>) TO KEYPAD BLK GROUND WIRE (V-) TO KEYPAD RED POWER WIRE (V+) TO KEYPAD GRN DATA WIRE (>) TO KEYPAD YEL DATA WIRE (<)
pwr_sup_conn-008-V0
Figure 3. Using a Supplementary Power
Supply
Notes
•Typical Fixed-Word Display:
6128RF/6148/6150/6150RF/6150V
•Typical Alpha Display: 6160/6160V/6160RF/6164
•The system supports up to 8 keypads, which can
be assigned to partitions in any combination
(see program fields *190-*196).
•For single 4-wire runs, determine the current
drain of all units, then refer to the Wiring Run
chart to determine the maximum length that can
be safely used for each wire size.
•Use supplementary power if the control’s aux.
power load for all devices exceeds 600mA.
Suggested power supply: AD12612
Keypad Addresses
Keypad Address Keypad Address
no. 1 16** no. 5 20
no. 2 17 no. 6 21
no. 3 18 no. 7 22
no. 4 19 no. 8 23
** The first keypad is address 16, which is always
enabled and set for partition 1 with all sounds on.
Keypads powered from supplies that do
not have a backup battery will not
function if AC mains power is lost. Make
sure to power at least one keypad in
each partition from the control’s auxiliary
power output.

Installation and Setup Guide
2-4
Wiring Run Chart For Devices* Drawing Aux Power From The Control (12V+ & 12V–)
Wire TOTAL CURRENT DRAIN OF ALL DEVICES CONNECTED TO A SINGLE WIRE RUN
Size 50 mA or less 100 mA 300 mA 500 mA 600 mA
0.6mm O.D. 152m 76m 24m 15m 13m
0.8mm O.D. 228.6m 116m 40m 24m 20m
1mm O.D. 396m 198m 67m 40m 35m
1.2mm O.D. 457m 305m 100m 70m 52m
* Includes Keypads, RF Receivers, Zone Expander/Relay Units, or TeleCommand Phone Module.
Maximum wire lengths for any device that is wired directly to the control can also be determined from the Wiring Run
Chart, based on the current drain of that device alone.
The length of all wire runs for all partitions combined must not exceed 457m when unshielded quad conductor cable
is used (228m if shielded/screened cable is used). This restriction is due to the capacitive effect on the data lines
when quad cable is used.
Sounder (Siren) Connections
1. Make sounder connections to alarm output terminals 3
(+) and 4 (–).
For supervised output, continue with steps 2 and 3.
2. Cut the red Siren Supervision Jumper located above
terminals 2 and 3 on the control board.
3. Connect a 2k ohm resistor across the terminals of the
last sounder.
+
+
_
_
2
EXTERNAL ALARM
SOUNDER
TERMINALS ON
CONTROL BOARD
ALARM
OUTPUT
TERMINALS
V48sounder-001-V0
3
4
CUT RED JUMPER ON CONTROL
BOARD TO ENABLE SIREN
(SOUNDER) SUPERVISION.
2000
OHM
EOL
RESISTOR
IF SIREN SUPERVISION IS ENABLED
(RED JUMPER ON CONTROL BOARD IS CUT)
CONNECT A 2000 OHM RESISTOR ACROSS
THE EXTERNAL SOUNDER AS SHOWN BY
THE DOTTED LINE.
DO NOT CONNECT THE RESISTOR AT THE
ALARM OUTPUT TERMINALS THEMSELVES!
OBSERVE
POLARITY
Figure 4. Sounder Wiring (Supervised)
Notes
•The 12VDC sounder output activates
when an alarm occurs.
•Total current drain from this output
cannot exceed 2 amps (going beyond 2
amps will overload the power supply,
or may cause the electronic circuit
protecting the sounder output to
activate).
•You must install a battery, since the
battery supplies this current.
•Do NOT perform steps 2 and 3 if using
a self-activated siren.

Mounting and Wiring the Control
2-5
Wiring the AC Transformer
Transformer:
Connect the Transformer to terminals 1 and 2 on the
control board. See wiring table at right for wire size to
use.
Use wired-in or plug-in 110 (e.g. 1321)/220VAC
transformer, with 16.5VAC, 25VA output.
Notes
•Use caution when wiring the
transformer to the control to guard
against blowing the transformer fuse
(the fuse is non-replaceable).
•Wiring to the AC transformer must
not exceed 76m using 1.2mm O.D.
wire. The voltage reading between
terminals 1 and 2 of the control must
not fall below 16.5VAC or an “AC
LOSS” message will be displayed.
•Do not connect to AC mains power
while making any wiring connections
to the control. As a safety precaution,
always power down the control when
making such connections.
Wiring Table
Distance from control Wire Gauge
Up to 15m 0.8mm O.D.
15-30m 1.0mm O.D.
30-76m 1.2mm O.D.

Installation and Setup Guide
2-6
Backup Battery
1. Place the 12-volt backup battery in the cabinet.
2. After all connections to the control are completed
and AC mains power has been applied, connect the
red and black flying leads on the control board to the
battery. Do not attach these leads to the battery
terminals until all connections are completed.
Battery Saver Feature: The battery will disconnect
from the system after its voltage decreases below
9VDC. This assists the control panel in recharging the
battery when AC is restored.
Notes
IMPORTANT: The panel will not power
up initially on battery power only. You
must plug the transformer in first, and
then connect the battery.
Earth Ground
Metal Cold Water Pipe or Earth Ground Rod:
Use a non-corrosive metal strap (copper is
recommended) firmly secured to the pipe/rod to which
the ground lead is electrically connected and secured.
Notes
•This product has been designed and tested to ensure
its resistance to damage from generally expected levels
of lightning and electrical discharge, and does not
normally require an earth ground.
•If an earth ground is desired for
additional protection in areas of severe
electrical activity, terminal 25 on the
control board, or the cabinet, may be
used as the ground connection point.
The examples of good earth grounds
listed at the left are available at some
installations.
AUXILIARY DEVICE CURRENT DRAIN WORKSHEET
DEVICE CURRENT # UNITS TOTAL CURRENT
6128RF Keypad/Transceiver 90mA standby/120mA alarm
6150RF Keypad/Transceiver 80mA standby/105mA alarm
6160RF Keypad/Transceiver 50mA standby/150mA alarm
6148 Fixed-Word Keypad 30mA standby/55mA alarm
6164 Keypad w/4-Zone Expander
and Relay
115mA standby/190mA alarm
5881RF Receiver 35mA
5883 RF Transceiver 80mA
5882EU/5882EUH Transceivers 60mA nominal, 85mA peak
4219 Zone Expander 35mA
4204 Relay Unit 15/180mA‡
4229 Zone Expander/Relay Unit 35/100mA‡
TeleCommand 55mA (standby)
119mA (local phone)
85mA (remote phone)
*
*
TOTAL =
(Current available from Aux. terminals = 600 mA max.)
*If using wired devices such as PIRs or Dual Tecs, refer to the specifications for that particular unit's
current drain.
‡
Figures are for relays OFF/relays ON.

Mounting and Wiring the Control
2-7
Basic Wired Zones
Normally Open Zones/Normally Open EOLR Zones
1. Connect open circuit devices in parallel across the
loop; for EOLR zones, connect the EOLR across the
loop wires at the last device.
2. Enable normally open/EOLR zones using Zone
Programming mode, “Hardwire Type” prompt.
Normally Closed Zones/Normally Closed EOLR Zones
1. Connect closed circuit devices in series in the high (+)
side of the loop; for EOLR zones, connect the EOLR in
series following the last device.
2. Enable normally closed/EOLR zones using Zone
Programming mode, “Hardwire Type” prompt..
Double-Balanced: Connections as shown (resistors
provided for one device in selected models); maximum of
8 sensors on each double-balanced zone.
IMPORTANT: Double-balanced zones provide unique
tamper signalling on the same 2 wires used for alarm
signalling, and should be used as burglary or emergency
zones only. Do not use double-balanced zones as fire
zones.
Zone Doubling: Connections as shown (resistors
provided).
2k
2k
2k
ZONE 3
2k
2k
2k
ZONE 4
12 13 14
zone-002-V0
TAMPER
CONTACTS
TAMPER
CONTACTS
10 11
6.2k
ZONE 10
3k
ZONE 2
zone-004-V0
Double Balanced Zones Zone Doubling
Figure 5. Configuring Zones
Notes
•EOLR: If the EOLR is not at the end of
the loop, the zone is not properly
supervised and the system may not
respond to an “open” on the zone.
•Zone 1 is intended only for EOLR
usage.
Zone Doubling:
This feature provides two unique zone
identifications for normally closed
sensors connected to each basic wired
zone (but does not increase the total
number of zones supported by the
control). Do not use zone doubling for
fire zones. If enabled (Zone
Programming mode, “Hardwire Type”
prompt, option “3”), basic wired zones
are automatically paired as follows:
Zone Paired with zone
2 10
3 11
4 12
5 13
6 14
NOTE: A short across the EOL (i.e., at
terminal) on either zone of a zone-
doubled pair or on a double-balanced
zone causes a tamper condition
(displayed at keypad as CHECK).

Installation and Setup Guide
2-8
Smoke Detectors
2-Wire Smoke Detectors
1. Connect up to sixteen 2-wire smoke detectors across
zone 1 terminals 8 (+) and 9 (-) as shown in the
Summary of Connections diagram. Observe proper
polarity when connecting the detectors.
2. Connect an EOL resistor across the loop wires at the
last detector.
4-Wire Smoke Detectors
3. Connect 4-wire smoke detectors (up to 16, depending
on detector current drain) to any zone from 2-8 as
shown on the next page. This control does not
automatically reset power to 4-wire smoke detector
zones, so you must use a relay (e.g., 4204, 4229), or
on-board trigger 17 to reset power (also required for
fire verification). Do this by programming the
designated relay/trigger as zone type 54 (fire zone
reset); see On-Board Trigger section for other
information.
Notes
•
••
•Fire Verification (zone type 16):
The control panel will “verify” a fire
alarm by resetting the smoke
detectors after the first alarm trigger,
and then waiting 90 seconds for a
second alarm trigger. If the smoke
detector does not trigger again, the
control will disregard the first trigger,
and no alarm signal will occur. This
feature eliminates false alarms from
smoke detectors due to electrical or
physical transients.
•The zone 1 alarm current supports
only one smoke detector in the
alarmed state.
•Do not use 4-wire smoke detectors on
zone 1.
•Maximum current for trigger 17
output for 4-wire smoke detectors is
100mA.
Figure 6. 4-Wire Smoke Detector Connections
+
+
2000
OHMS
EOLR
HEAT
DETECTOR
RED
EOL
POWER
SUPERVISION
RELAY MODULE
A77-716B.
USE N.O.
CONTACT,
WHICH CLOSES
WHEN POWER
IS APPLIED.
VIOLET
AUX PWR
OUTPUT
TERMINALS
5
4
_
_
+
_
BLK
_
+
4_wiresmk-007-V0
TO ZONE TERM. ( )
TO ZONE TERM. ( )
RELAY
CONTACT OPENS
MOMENTARILY UPON
FIRE ALARM RESET
PROGRAM
RELAY
AS ZONE
TYPE 54
(FIRE ZONE
RESET)
4-WIRE SMOKE
OR COMBUSTION
DETECTOR
N.C.
N.O.
4-Wire Smoke Detector Using Relay for Power Reset
+
2000
OHMS
EOLR
HEAT
DETECTOR
RED
VIOLET
AUX PWR 5
_
+
_
BLK
_
+
4_wiresmk-008-V0
4-WIRE SMOKE
OR COMBUSTION
DETECTOR
( )
( )
+
_
TO ZONE TERM. ( )
TO ZONE TERM. ( )
TO OUTPUT 17
PROGRAM OUTPUT 17
FOR "OUT NORM
LOW" = YES IN 79 MENU
MODE AND AS ZONE
TYPE 54 IN
80 MENU MODE
EOL
POWER
SUPERVISION
RELAY MODULE
A77-716B.
USE N.O.
CONTACT,
WHICH CLOSES
WHEN POWER
IS APPLIED.
N.O.
4-Wire Smoke Detector Using Output 17 for Power Reset

Mounting and Wiring the Control
2-9
4219/4229 Expansion Zones
1. Connect each module to the control’s keypad
terminals.
2. Assign the module a device address of 08
using its DIP switches. The device address
determines the zone numbers being used, as
shown below.
Expander Module Addresses
Zones… Device Address…
17-24 08
3. Connect sensors to the module’s loops.
4. If using relays with the 4229, connect the
desired field wiring to the unit's relay
contact terminals.
Notes
•Supports up to 8 expansion zones (NO or NC)
using 4219/4229 Zone Expander Modules as
follows:
•Use 1000 ohm end-of-line resistors at the end
of loops connected to the 4219/4229 modules.
(End-of line resistors used on the control
terminals are 2000 ohms.)
•Expansion zones have normal response time
(400–500 msec), except zone connected to each
module’s loop “A,” which can be set for fast
response† (10–15 msec).
† Do not use fast response in Western Europe;
fast response is not permitted by
EN50131-1/prEN50131-3.
BRN
GRN
BLK
(–) GROUND
RED
(+) 12VDC
YEL
4
3
2
1
ZONES ABC DFGH
DIP SWITCH
FOR SETTING ADDRESS
AND ZONE "A" RESPONSE
TAMPER JUMPER POSITION
4229 IN CABINET
(NOT TAMPER)
4229 REMOTE
(TAMPER PROTECTED) TB1
4229
TB2
WHT
GRY
VIO
BLK
YEL
ORG
NO NC C
GND
NO NC C
RLY
1
RLY
2
RELAYS OFF
RELAY
CONNECTOR RELAY
2
RELAY
1
(TERM 6)
(TERM 4)
(TERM 5)
(TERM 7)
NO C NC
TERMINALS ON
CONTROL PANEL
1
2
3
4DATA OUT (>)
TO CONTROL
DATA IN (<)
FROM
CONTROL
5811
REED
(TAMPER)
SWITCH
2
E
134 6 7910 12
TERMINATE EACH
PROGRAMMED ZONE
WITH 1000 OHM (1K)
END-OF-LINE RESISTOR
(EACH ZONE'S MAX.
LOOP RESISTANCE
300 OHMS + EOL)
4-PIN CONSOLE PLUG
EITHER OR BOTH CAN BE USED
4229-002-V0
Figure 7. Wiring Connections, 4219 & 4229 (4229 shown)

Installation and Setup Guide
2-10
6164 Keypad Expansion Zones
1. Connect each keypad to the control’s keypad
terminals.
2. Using the keypad’s program mode, assign the
keypad a unique keypad address (16-23), and
assign a device address of 08 which provides
expansion zones 17-20.
3. Connect sensors to the keypad’s zone
terminals.
4. If using the keypad relay, connect the desired
field wiring to the keypad's relay contact
terminals.
See 6164 Keypad Instructions for other
mounting, wiring, and programming
information.
Notes
•Each 6164 keypad supports up to 4 wired
expansion EOLR or double-balanced zones
and one relay output.
•Use 2000 ohm end-of-line resistors at the
end of loops connected to the 6164 keypads.
•Enter 6164 keypad program mode by
pressing and holding down both the [1] and
[3] keys within 60 seconds of power up.
•Enable the keypad addresses using data
fields *191-*196 as required.
•Program keypad zones using *56 Menu
mode. Keypad zones 1-4 correspond to the
respective groups of zones shown in the
chart at left, where keypad zone 1 is the
lowest zone number in each group.
[-] GROUND (
-
G
Z1
Z2
(Z1
&
Z2)
(Z3
&
Z4)
Z4
Z3
2K
2K
2K
2K
TAMPER
CONTACTS
TAMPER
CONTACTS N.O.
N.C.
DOUBLE BALANCED
CONVENTIONAL
EOLR
[Y] DATA IN (<
)
[+] +12VDC IN
[G] DATA OUT
OPTIONAL
Y +
N.O.
C.
N.C.

Mounting and Wiring the Control
2-11
Installing the RF Receiver
Use one of the following receivers:
RF Receiver Number of Zones
5881ENL up to 8 (including keyfob
buttons)
5881ENM up to 16 (including keyfob
buttons)
1. Set Device Address to “00” as described in its
instructions (set all switches to the right, “off”
position).
2. Mount the receiver, noting that the RF receiver
can detect signals from transmitters within a
nominal range of 67m.
3. Connect the receiver's wire harness to the
control's keypad terminals. Plug the connector
at the other end of the harness into the
receiver. Refer to the installation instructions
provided with the receiver for further
installation procedures regarding antenna
mounting, etc.
Notes
•The receiver is supervised and a trouble
report is sent (“CHECK 100” displayed) if
communication between the panel and
receiver is interrupted, or if no valid RF
signals from at least one supervised
transmitter are received within 12 hours.
•Only one receiver can be installed in a system.
If the receiver is mounted remotely:
•Place the RF receiver in a high, centrally
located area for best reception.
•Do not locate the receiver or transmitters on
or near metal objects. This will decrease
range and/or block transmissions.
•Do not locate the RF receiver in an area of
high RF interference (indicated by frequent
or prolonged lighting of the LED in the
receiver; random flicker is OK).
•Do not locate RF receiver closer than 3m
from any keypads to avoid interference from
the microprocessors in those units.
Figure 8. 5881EN RF Receiver (cover removed)
WIRELESS ZONE NUMBERS
transmitter zones 9-24
button or transmitter zones 49-64
Installing a 5800TM Module
1. Mount the 5800TM next to the RF receiver
(between one and two feet from the receiver’s
antennas) using its accompanying mounting
bracket. Do not install within the control
cabinet.
2. Connect the 5800TM to the control panel’s
keypad connection terminals as shown on the
Summary of Connections diagram and set to
address 28.
Notes
•Use this module only in 345Hz RF systems
and if you are using one or more wireless bi-
directional keypads or keyfob; 5800TM is not
necessary if using a Transceiver (e.g., 5883).
•The 5800TM must be set to address 28 (cut
red-W1 jumper).
•The 5800TM can be used in partition 1 only.
•For additional information regarding the
5800TM, refer to the 5800TM’s instructions.

Installation and Setup Guide
2-12
Installing the Transmitters
1. To be sure reception of the transmitter's signal
at the proposed mounting location is adequate,
perform a Go/No Go Test (see the Testing the
System section).
2. Install transmitters in accordance with the
instructions provided with each.
3. Set 5827, 5827BD, 5804BD wireless keypads to
the programmed House ID (field *24), using its
DIP switches (5827) or follow the instructions
provided with the device.
Notes
•Refer to the table of compatible devices at
the back of this manual.
•Supervised transmitters†send check-in signal
s
to the receiver at 70-90 minute intervals. If at
least one check-in message is not received fro
m
each transmitter within a 12-hour period, the
“missing” transmitter number(s) and “CHEC
K
is displayed.
† Hand-held transmitters (e.g., 5802, 5802CP, 5804,
5804BD, 5827, 5827BD) do not send check-in
signals.
Transmitter Battery Life
• See Wireless Transmitter paragraph in the Limitations of This Alarm System statement located
at the end of this manual for information on transmitter battery life.
• Some transmitters (e.g., 5802 and 5802CP) contain long-life but non-replaceable batteries, and no
battery installation is required. At the end of their life, the complete unit must be replaced (and a
new serial number enrolled by the control).
• Button-type transmitters (such as 5801, 5802, and 5802CP) should be periodically tested for
battery life.
• The 5802EU, 5802MN, 5802MN2, 5804EU, and 5804 Button Transmitters have replaceable
batteries.
Do not install batteries in wireless transmitters until you are ready to enroll during system
programming. After enrolling, batteries need not be removed.
Installing a Keyswitch
1. Connect the 4146 keyswitch's normally open
momentary switch to a zone’s terminals
(zones 2-8). Remove the 2000 ohm EOL
resistor if connected across the selected zone.
2. Using a standard keypad cable as shown:
Connect the yellow and white keyswitch wires
to trigger connector pin 3 (+12V).
Connect the Red and Green LED wires to the
appropriate output 17/output 18 trigger
connector pins.
3. Connect a 2000 ohm EOL resistor across the
momentary switch.
4. You can wire an optional closed-circuit
tamper switch (model 112) in series with the
zone. If the switchplate is then removed from
the wall, the tamper will open, disabling
keyswitch operation until the system is next
disarmed from the keypad.
If the tamper is opened when the system is
armed, an alarm will occur.
Notes
•Use 4146 keyswitch or any normally open
keyswitch.
•Use only one keyswitch per partition.
•If using a keyswitch in more than one partition,
you must use relays (not the on-board triggers)
for the Red/Green LED functions (step 2).
•When using a keyswitch, the zone it is
connected to is no longer available for use as a
protective zone.
•Use *56 Menu mode to program the keyswitch
zone and assign it zone type 77.
•Use *80 Menu mode to program the LED
functions: program outputs 17 and 18 for
system operation zone type 78 (red LED)
and 79 (green LED) as appropriate (see
Output Device Programming section).