Hongda USA Mermaid tribe User manual

138491384913849
Mermaid tribe Mermaid tribe Mermaid tribe
13849 Instruction manual13849 Instruction manual13849 Instruction manual

1
Making tips
1. LED wiring indication:
White=Positive;Grey=Negative.
2.Use a craft blade to carefully
skim over the plastic to bare the
copper wire.
3. For LED wiring extension,
please refer to the below steps:
Twist the copper of
both LED wire and
extension wire together.
Do the same on the
white wire.
Remarks: Tie a knot
at the end of the grey
wire to differentiate
the polarity.
Place the duly twist
wire on the tapes
provided.
Roll and wrap the wire.
Place another wire
next to it.
Remarks: DO NOT
contact both copper
wire to avoid short
circuit.
Roll and wrap it together.
LED
wire
Extension
wire
LED
wire
Tips for assembling
1.Picures shown on the package may
be slightly different from the actual
product.
2.Please use the provided tracing
paper for cutting purpose to achieve
the best outcome.
3.Product designs and specification
may be subject to change without
advance notice for purpose of
making improvement.
4.Testing on LED function:
DO NOT contact the LED
wire end direct to the
battery cell.
Use the provide battery
holder. Make sue the correct
polarity.
Warnings
The product is not suitable for children
under 14 years old. The should be under
custody of adults when playing with the
product.
There are small parts, please do not swallow
them for avoiding dangerous accidents.
Please also play attention to the sharp-
pointed materials to avoid injuries.
How to assemble the battery holder
1.Material and tools needed:
- Battery holder, LED bulb,
tape, screw driver and 2 piece
AA size battery(not provided)
2. Use screw driver and
take the lid off from the
battery holder.
3. Insert the battery take
notes on the polarity.
4. Connect the red wire to
grey wire. Connect the black
wire to white wire.
5.Wrap the exposed wire
with the tapes. 6. Place the box lid and
fastness with screw driver.
Scissors:
Can be used
to cut printed
paper,
cloth,etc.
Screw Driver:
For fixing screws,
mostly can be used
to install doors and
music components.
Tweezers:
For holding small
materials and
rolling up iron wire.
Cutter kinfe:
For peeling off
power wire skin
and cutting off
materials.
Ruler:
For measuring
materials to identify
the number of
materials so as to
enhance work
efficiency.
Self-provided tools
“-”negative
“+”positive

2
Big sofaSmall sofa
Circular sofa
Corner sofa
Flower
shelving
Street lamp
TV
Bed
Window
Toilet
Cabinet
Dog
Floor
lamp
Big sofa
Corner sofa
Swimming pool
Plant
Piano
Dining
table
Bedside tableBathroom
Bed flower shelving
Product information

D01
D02 D02
D04
D05
D03 D03
K03
K04
L07(6pieces)
D05 D02
(2pieces)
(back view)
K03(big sofa big cushion)
K04(big sofa big cushion 1)
K04(big sofa big cushion 2)
D04
D04
D03 (2pieces)
L07(4pieces)
K03(small sofa covered edge)
D07 D03
D06
L07
D07
D02
D02
D02
D06
K03(small sofa cushion) L07
3
P1 P2
P1
P3
P2
P2
P2 P1
P5 P4
P6 P7
P8
P6
P7 P9
P7
D01
K03(big sofa backrest) K03(big sofa small cushion) K03(big sofa big cushion)
K03(big sofa handrail)
K03(big sofa covered edge)
K04(big sofa small cushion1)
K04(big sofa small cushion2)
K04(big sofa big cushion1)
K04(big sofa big cushion2)
K03(small sofa handrail)
K03(small sofa backrest)
K03(small sofa covered edge)
K03(small sofa cushion)
K04(small sofa small cushion1)
K04(small sofa small cushion2)
P3 P1
P3
P5 P5
P8
P6
P9
P3 P2 P1
P3
K04(big sofa small cushion 1)
K04(big sofa small cushion 2)
K03(big sofa small cushion)
(back view)
P4
L07
L07
L07
L07
L07
L07
L07
L07
Big sofa
Cut out the material K03,K04 according
to the template paper before making.
K03(big sofa backrest)
K03(big sofa handrail)
Make two handrails according to the making method of backrest.
K03(big sofa covered edge) Cut off the excess Cut the cloth off at the position above shown, attach it to D01 as shown.
Make two small cushions according to the making method of big cushion.
Small sofa
Cut out the material K03,K04 according
to the template paper before making.
Cut off the excess Cut the cloth off at the position above shown,
attach it to D03 as shown.
K03(small sofa handrail)
(2pieces)
Make two handrails according to the
making method of big sofa backrest.
K03(small sofa backrest)
Make a small cushion according to the making method of big sofa small cushion.

L07(3pieces)
D08 D09 D09
K03(circular sofa covered edge)
D08
K04(circular sofa cushion) K03(circular sofa cushion)
(back view)
(fold and stick well)
L07
D10
D11
D11
K03(corner sofa covered edge)
D10
K04(corner sofa cushion)
D10
A30-1-1
A30-1-2
D12
D14
D14
D13
D14
D14
L01
M24
K15:1.5cm
M15:0.1cm
M14:0.1cm
M13:0.3cm
M17
Cut out some leaves from M24
and put them on L01 as shown.
cut M13,M14,M15 with
a knife as shown.
A30-2 A30-3 A30-4
A30-5 A30-6
A30-2 A30-3
A30-4
A30-2
A30-5
A30-6
Following above step to make the box as shown. According to the same method to make other boxes.
4
A30-1-3
Fold A30-1-3 in a "Z" form according to the lines as shown.
P10
P11
P12
P13
K03(Circular sofa cushion)
K03(circular sofa cushion covered edge)
K03(circular sofa covered edge)
K04(circular sofa cushion)
K03(corner sofa cushion)
K04(corner sofa cushion)
K03(corner sofa cushion covered edge)
K03(corner sofa covered edge)
P11
P10
P12
P13
A30-1-2
M14:0.3cmM13:0.3cm M15:0.3cm L01
D12 D14 D14
M24
A30-1-1 K15:4.5cm M17
D13 D14D14
Cut K15 out of three pieces(1.5cm),
attach M13,M14,M15 to K15 as shown.
Cut out the material K03,K04 according
to the template paper before making.
Circular sofa
Cut the cloth off at the position above shown, attach it to D09 as shown.
the top and bottom of D09
need to be pasted as shown.
K03(circular sofa cushion covered edge)
Cover up D08 with K03, cut off the excess as shown. Cut off the excess
the top and bottom of D11
need to be pasted as shown.
Cut out the material K03,K04 according
to the template paper before making.
Corner sofa
Cut the cloth off at the position above shown, attach it to D11 as shown.
Cut off the excess
Cut off the excess
(fold and stick well)
Cover up D10 with K03, cut off the excess as shown.
K03(corner sofa cushion)
K03(corner sofa cushion covered edge)
Tabel
Attach A30-1-1,A30-1-2 on D12 as shown.
Box

M09
A30-7
A30-7
C14
C17
C16
C16
C15
C14
Attach A30-7 to C14 as shown.
M09
A30-6
A30-5
Mirror
template
A30-8G14
K07
G14
A30-8
K07(mirror template)
L07(4pieces)
E13
E14
E15
E13 E14
E15
E14
E13
E16
E16
E13E14
E13
E13
E16
E14
E17
E12
E11
L07 L07
M07
L03
M01
M02
A30-9
A30-10
A30-13
K13:2cm
K14:7.2cm
(5pieces)
E09
A30-10
A30-11
E08
A30-12
E07 E10
E02
K14:0.8cm E03
E02
E04 E06
E05
Cut out K07 according to the template of K07, attach them to the wood as shown.
E06
E04
E05 E06
E05
K16:5cm
K13:2cm M01
M02 K02(wash basin)
K14:3.2cm
Cut K14 out of five pieces(0.8cm)
and bend it as shown.
A30-13
M07
K16:3.8cm K16:0.6cm L03
M10:0.1cm
(back view)
5
K07(wash basin)
E01
E02 E03
E03
E04
E05
E05
E08 E08
E10
E13 E13 E14
E15
E16
E12
E11
E17 E17
C14
C15
C16 C16 C17
A30-9
E01
E02
E03
2mm
C15
C16
C15
E14
E13
E02
E02
E03
E03
L07
L07
K02
(wash basin)
K09
(Gas burner)
A30-11
E07
E09 A30-12
E06 E06
TV console
Mirror
Refrigerator
Cut out the material K02,K07 and K09 according
to the template paper before making.
K07
(Gas burner)
K09
(Gas burner)
K07
(Gas burner)
Cut out K07 and K09 according to
the template, and attach them
together as shown.
Cut K14 out of a piece(3.2cm)
and bend it as shown.
(2pieces)
Cut K16 out of two pieces(0.6cm)
and bend it as shown,attach them to the pot form.
Cabinet

A30-14-2
A30-15-1 A30-15-3
(3pieces)
A30-14-1
F10
A30-14-2
F11
F12
F12
F14
A30-15-1
A30-15-2
(Template:1.K03 dining chair cushion 2.K04 dining chair cushion 3.A27 cake rack)
A30-15-3
F15
F13
F15 K04(dining chair cushion)
F16
F13
K03(dining chair cushion)
M03 ( 2pieces)
L02 ( 2 pieces) M12 M04
(2pieces)
+
+M04
M12
K12:13cm
M01 ( 3pieces)
K12:1.2cm
M03
L02
M02 A27
The making method,
please refer to page4
A30-16
A30-17 A30-18
L04 ( 2pieces) L05 ( 2 pieces) L07 ( 2pieces)
L22 :1.6cm K11:7cm M10 :0.5 cm M11:0.5cm
A30-16
F02
K12:1cm (2pieces)
F01
F05
F02
F01
F04
F06
the boxes we made before
F03
K12:0.5cm
L04
F09
F08
A30-17
L07
L05
0.8cm
L22 :0.8cm
A30-18
M10 :1cm*5pieces
K02(can) K11:3.5cm M11:0.1cm*5pieces
A30-19 A30-18
A30-20
1.3cm
K16:2.6cm
K16:2.6cm
L04
L21
K10:2cm
K18
A30-19
G06
G05
G07
K10:2cm
L04
K18
A30-19
L21
6
A27(cake rack1)A27(cake rack2)
K12:5.6cm K12:5cm
M01 M01 M02
Follow the above steps to make the cake rack.
M10:0.1cm(4pieces)
M11:0.1cm(6pieces)
F10
F11 F12 F12
F14 F14 F14
F15 F15 F15
F13 F13
F13
F13
F13 F13
F16
F16
F16
A30-14-1
A30-15-2
G05
G06
G07
G05
G07
F03
F01
F04
F05
F06
F07 F08
F09
F01
F03
F02
2mm
G05
F01
G07
G05
F03
1.8cm 1.6cm
Dining table
Attach A30-14-1,A30-14-2 to F10 as shown.
Cover up K04 with K03, attach it
on the chair form as shown.
Cut out M10 and M11 according to before method,
attach them to the cake rack as shown.
Wall cabinet
Attach K02 on canning form, tie it up with K11 as shown, another method of canning is the same.
Bedside table
Cut K16 out of a piece(2.6cm)and bend it as shown.
A30-20

A30-22
A30-21
H02
H03 H04
H03
H02 H04
H03
H05
H06
H05
H06
H04
H07
H06
H07
H08
H09
H08
H09
H10
A30-21
H12
H11
H10
(the cover for piano keyboard)
H14
(Template:1.K02 piano stool
2.K04 piano stool)
K02 K04
H16
H16
H13
H01
A30-22
H01
H15 H17
H19
H18 H18
H18
H17
H19
H18
K02(piano stool)
K04(piano stool)
+
Cover up K04 with K02 as above shown.
L04 L19
A30-23
A30-24
K04
G08
A30-23
(To carve a hole with a knife)
A30-24 G09
G10
G11
G11 G10
G11
G12
G13
G08
K04(wash basin towel)
+
L04
L19
Attach K04 to the combination as shown.
D18
D17
K18
K01(floor lamp)
D16
D15
K18
Follow above steps to make the floor lamp as shown.
7
G08
G09
G11
G11
G10 G12
G13
G13
H01 H02
H03
H04 H05
H06 H07
H13
H14
H15
H16
H08H09H10
H14
H11
H04
H05
(Attach A30-24 to the back of G08)
G13
H05
G10
G11
G10
K01(floor lamp)
D16
D16
D15
D17
D18
Piano
(the cover for piano keyboard)
Attach A30-21 to H10,
fold the remaining part as shown.
Piano stool
Cabinet Floor lamp

L12
( 2 pieces) A30-25
J04
J05
J01
Bottom
(one side down with PVC film)
Cut off the excess
J02
J04
L16
L15
L14
L12
L13
K11:1.8cm
L06
(3pieces)
Cut K11 out of two pieces(1.8cm), attach beads to K11 as above shown.
A30-26
K18
(3pieces)
G01
G03
G02
G04
(back view)
A30-26
K04(bed)
G03
G03
G02
Attach A30-26 to G04 as shown.Attach K04 on the bed form as shown.
1cm
K03(bed)
K02(bed)
M20
( 2pieces) M23
(2pieces)
M21
( 2pieces)
A30-27
M24
J12
J08
J07
J08
J08 J07
J08
A27(flower frame)
Attach A27 to the flower shelving form as shown.
J09
J10
J11
J12
A30-27
J13
K08(medium flower pot)
(2pieces)
Follow above steps to make the flower pot.
Repeat above steps for all flower pots.
J14
J15
M24 M20
M21
M23
Cut out the small leaves on M24 and cut the flower bub in half and put them in the flower pot as shown.
8
K01(pillow)
Repeat above steps for all pillows.
Apply glue to K02 according to
the dotted lines as shown.
K18
K02(pillow)
Insert some cotton K18 to the pillow form,
apply glue onto the pillow form as shown.
L13
( 2 pieces)
L14
( 2 pieces) L15
( 2 pieces)
L16
( 2 pieces)
K18
A27(Burn oven)
K11:3.6 cm
J01
J02
J03
J05
J05
J05
J06(6pieces)
G01 G01
G02
G03
G04
G04
G04
J07 J07 J09
J10
J08 J08
J08
J08
J08
J08
J08 J08 J08
J13J14J15
J11
G03
G01
J13
J08 J08
K08(medium flower pot)
A27(flower frame)
M08
K02(pillow)
(5pieces) (1piece)
K01(pillow)
(1piece)
K03(pillow)
K04(bed)K03(bed)
K02(bed)
A30-25
M08
K18
J02
J04
J03
side view
K03(pillow)
K02(pillow)
Burn oven
A27(Burn oven)
Bed Flower shelving
A27(flower frame)A27(flower frame)

K08 (small flower pot)
A30-28 A30-29
J16
J17 J17
J18 J18
J17
J16
A30-28
J17
J16
K08 (big flower pot)
Attach J17 to J16, and then attach K08 to the combination as shown.
M23M22
M21 M20
M24
K17
(2pieces)
A30-29 J18 K08 (small flower pot)
M24
M23
M21
L04 L07 L19 L20
M01
( 3pieces) M02 M03
M04
A27
K12:12cm
M04
K12:12cm
M03
M02
M01
A30-30-1
A30-30-2 A30-30-3
A30-30-3
G16
G15
A30-30-2
A30-30-1
(back view) (back view)
G16
L04
L19 L20
L07
G15
L08(6pieces)
K18
Use tools to make the hole in L10 bigger so the wires can pass through.
L08
small hole
L10 K18
M06
L11
K18
K18
M06
L11
Wrap the wires together, attach M016 and L11 to the K18 as shown.
M18 A30-34
M18 A30-34
Attach A30-34 to M018, cut off the excess as shown.
9
A30-33
K04(dog claw carpet1) K06(dog claw carpet 2) M16
Attach K06 to K04 as above shown.
K04(slipper 1)
K02(slipper 2)
(2pieces)
Follow above steps to make the slippers as shown.
L06
M25
M24(2pieces)
M19
(2pieces)
M24
M19 L06
M25
K10:3cm
L10
G15 G16
J16
J17
M24
M20
( 2pieces)
M23
(2pieces)
M21
( 2pieces)
M22
(2pieces)
K08 (big flower pot)
M01
6cm
6cm
3.5cm
Flower pot Bathroom Dog claw carpet
Slippers
Potted plant
Toilet
Second floor
chandelier
chandelier
A30-30-2 A30-30-3
A28(浴室厚PVC模板)
Trace the dotted line on A28 according to the template with a knife and fold it as above shown.

L06
K13:2cm
M01(2pieces)
K18
K13:2cm L06
M01
K18
Cut K13 with 2cm long,
and bend it above shown.
M01
M01
L17
L18 (2pieces) K18
A30-32
K18
L18 A30-32
L18
L17
Wrap the wires with A30-32 as above shown.
L23
K18
L23
K18
Attach K18 to L23, cut a opening on the bottom of L23 as above shown.
A01
A30-35
Attach A30-35 on A01, the four edges are also glued as shown.
A02
A30-36
A08
A30-37
A30-38
A03
A30-39
A30-39
A30-39
Attach A30-39 on K09 and cut off ,
and then attach them to A03 as abvoe shown.
A09
A30-40 B06
A23
A30-41-1
A30-41-2
A30-42
A22
(turn over)
A22
A30-43
A30-44
C12 A30-44
C12
(back view) C13
A30-45
Attach A30-45 on
C13 as shown.
L08(3pieces)
F17
K10:1.5cm
F18
F17
L09
small hole
K19
K10:0.5cm
L08
M05
M06
Roll up A30-31 and cut a opening with scissors.
F18
K10:0.5cm
fold and
paste
10
M05
M06
A30-31
K19
A30-31
F18(5pieces)
L09
First floor chandelier
Use tools to make the hole in L09 bigger so the wires can pass through.
Wall lamp
Chandelier
Street lamp
opening
Outer frame
Attach A30-42 on A22,
the four edges are also glued as shown.

A30-46-1 (turn over)
A30-46-2
A10 A10
wall lamp
B10
A30-47
A04
B08
(turn over)
A30-48
A07
A30-39
A30-49
A06
(Note:attach on no color side)
A15
A14
A30-50
bevel edge
Attach A30-51 to
A14(no color side),
cut off the excess.
A30-51 A30-52
A13
B05
Attach A30-52 to a13(no color side),
cut of the excess.
A12
A11
A30-53
A30-54
A12
B07
A11
A30-55 (turn over)
Mirror B09 Bath
cabinet
bevel edge
wall cabinet
first floor chandelier
A08
5.5cm
5.7cm chandelier
A14
5.5cm
5cm
N01
N02
N03
second floor chandelier
11
2cm
Outer frame
(white edge)
Attach A30-39 on K09, cut out and attach to A07 as above shown.
(Note:attach on no color side)
(white edge)
Music machine core manual guide
(If you have purchased the music machine
core, please fix it firstly)
N01 Music
machine core
1piece
N02
Music machine
core handle
1piece
N03 Screw
3pieces
Installation of lamps
bevel edge

A06
A30-56-1
A05 Attach A30-56 to A06,two edges are also glue as shown in red lines.
blue color LED lamp K19
Attach K19 on A30-56-1 as above shown,paste A30-56-2 on the wires.
A30-56-2
A01
A18
A17
A18
A17
A17
A18
A16 A19
A19
A16
A19
A19
A21
A20
A21
A20
A21 A30-57
burn oven street lamp
floor
lamp
A06
A02
pass the wires through the A16 hole, attach A06 to A01 as shown. Thread the wires of the burn oven, street lamp and
floor lamp through the holes in A02 as shown.
A02
A30-58
A30-58
A30-58
swimming
pool
Attach the A27 swimming pool as above shown.
A25
A25
A26
A25
A26 A25
A29(swimming pool)
Attach A29 on the top of
swimming pool form as shown.
B11
A03 A07
A05
A06
Fold and
attach it
A30-59
C01
A30-39
Attach A30-39 on K09, cut
off and attach to the C01 as
above shown.
A30-60
C03
A30-61
C02
C04
A30-62
12
A05
A03
A06
A18
A18
A16
A17
A19
A19
A20
A21
A21
C01 C02
C03
C04
C06
C05(9pieces)
C07(9pieces)C08
A21
A20
A21
A05
A26
Top view
A27(swimming pool 1)
A18
A02
street
lamp
Swimming pool Outer frame
Trace the dotted line on A27 according to the template with a knife
and fold it as above shown, and then fold it.
burn oven
Tear off kraft paper of
A25 as shown.
Stairs

C02
C02
A06
A06
C03
C01 C01 C03
C04
C04
C08
C04
C05
C07
side view:
C05
C06
C07
C05
side view:
A22
A08
Thread the wires of first
floor chandelier through the
hole in A03 as shown.
Thread the wires of wall lamp
through the hole in the A03 as shown.
A09
A10
A23
A04
B02 B01
B01
B03
B04
(template:1.A27 french window template
2.K05 french window template)
B02
A27
K05
Cut off A27 according to the template to A27.
attach A27(french window 1 to B02 as above shown.
K05(french window 1)
B03
K05( french window 2)
B04
B01 B01
A27(french window 4)A27(french window 5)
B01
B01
B02
B01 B03
B04
B04
B03
A28
(template:1.A28 railing 2.A27 stairs)
C09
A27
C11
C10
B16
B12
B13
B14
B15
B12 B14
B16
B13
B15 B16
B15
B14
B13
B16
B15
According to the same way of railing 1to make the railing 2 as shown.
B13 B14
B12
A28(railing 1)
A28(railing 2)
C10
A27(Stairs 1)
A27(stairs 2)
C11
C09
railing 1
railing 2
13
C03
C02
A07 C08
A27(french window 1)
right
left
A27(french window 2)A27(french window 3)
A27(stairs 3)
Attach K05 to B02 as shown.
(note: paste on the side without A27)
Attach K05 to B03 as shown.
(note: paste on the side without A27)
Cut off A27 according to the template to A27.
attach A27(french window 2 to B04 as above shown.
left
right
Trace the dotted line on A28 according to the template with a knife
and fold it as above shown, and then attach to B15 and B16.

railing1 C09 C10
C11
C09
C11
railing 2
bedside
lamp
Pass the wires of bedside lamp through A03 and fix it well as shown.
bed bathroom
silppers toilet
piano
refrigerator
cabinet
A14
A13
A15
A30-63 dining table
corner
sofa
dog TV console
chair
big flower
pot A30-64
plant table
street
lamp
circular
sofa
plant
flower
shelving
fix the wires to A03 as above shown.
14
C10
Pass the wires of second floor
chandelier through A03 and fix it
well as shown.
Trim all the LED wiring to
the same length.
Use a craft blade to carefully skim over the plastic to bare
the copper wire. Twist the same color wire together.
(note: twist the blue wire with grey wire together)

white wire from LED lamp blue and grey wire from LED lamp
N04
N05
N06
red wire from battery box
black wire from battery box
K20 K21
Attention: Please keep the instruction for future enquires after installation.
Installation of dust proof cover
(For updated version, the parts need to be purchased separately)
Scale 1:10
N04 Transparent cover
0.15*25*33 1piece
1. Tear off kraft paper of each
piece of transparent cover.
2.Paste N04,N05,and N06 together to complete the dust proof cover as shown.
Statement: the lamp wires cannot be
inserted into the output socket.
– – Can use 7 batteries
– – Please notice the place of anode
and cathode when pit in the batteries
– – Rechargeable batteries are not blunt electricity
– – Rechargeable batteries can only be charged
under adult supervision
– – Rechargeable batteries should be
removed from the toy before charging
– – Different types of batteries cannot mix;
Do not mix new batteries in use with semi-used
batteries.
– – Run out of battery should be removed from the toy
– – The power shall not be short circuit Twist the following wire together:
(I) BLACK wire from the battery box with the WHITE
wire from LED bulb.
(II) RED wire from the battery box with the GREY
wire and blue wire from LED bulb.
Roll and seal the duly twist copper with
the white tape K21 provided.
Place the battery box in the allocated space.
Scale 1:10
N05 Transparent cover
0.15*22*33 2pieces
Scale 1:10
N04 Transparent cover
0.15*22*24.7 2pieces
Photo of Dust proof cover