Hongda USA S2007 User manual

S2007 Instruction manual
S2007
Happy Kitchen

1
12
Tips for assembling
1.Because this product contains small parts, children need to use this product with an adult to avoid accidental ingestion and cause suffocation hazard.
There are sharp objects in the product, be careful not to pierce people to avoid injury.
2.After all the materials are used in the required amount in the operation steps, put the remaining materials back into the original bag until the installation is completed.
(Avoid losing materials during the installation process)
3.The unit of dimension marked in the step diagram is "cm".
4.Tips for making template paper: Put the template on the back of the material, fix it with some small double-sided tape, and then cut out the material to prevent the
cloth or template from moving in the cutting process, or causing errors in the cut material. Or lead to insufficient materials.
5.According to the "Parts Rule Example" at the bottom of this page, refer to the parts on the part number drawing, find the actual product and compare it with the bill
of materials, and then install it after confirming that it is correct. (Wooden parts only)
6.It is not advisable to apply too much glue, so as not to wait for a longer time to dry, and overflow will affect the effect of the finished product.
7.There are unavoidable small deviations in the color of wood, fabric, and beads of different batches, without notice, thanks for understanding.
Tips for Assembling Wood
Find the corresponding block number,
use a knife in the connection point
gently press, you can take out the wood.
Use a knife to
smooth out the burr.
Or use sandpaper to smooth
out the burr
Be sure to test the LED lights before making the lighting,note that the LED
white wire to the negative, gray wire to the positive reference to the
following figure operation test.
Testing on LED function
DO NOT contact the
LED wire end direct
to the battery cell.
Use the provide battery
holder. Make sue the
correct polarity.
How to assemble the battery holder
1.Material and tools needed:
- Battery holder, LED bulb,
tape, screw driver and 2 pieces
AAA size battery(not provided)
2. Use screw driver and
take the lid off from the
battery holder.
3. Insert the battery take
notes on the polarity.
4. Connect the red wire
to grey wire. Connect
the black wire to white
wire.
5.Wrap the exposed wire
with the tapes.
6. Place the box lid and
fastness with screw driver.
Examples of parts rule:
“-”negative
“+”positive
A01:The parts are directly in the box: B01: The parts are in the B bag; C01: The parts are in the C bag, and so on (Note: The printing paper is displayed in the step A05-1:
The printing paper is placed directly in the box , The part number is A05-1. In the step, the template paper A06-C01 is displayed, A06 is the template paper,
D01 is the cutting template used for the corresponding material, D01-1, D01-2 are the part numbers for the parts, and the printing paper and template paper
are directly placed in the packaging box.)

refrigerator page 3
page 4-5
wall lamp
curtain
outer frame
cupboard
page 3-4
page 10
printing paper&
template paper
rack
kitchen utensil
page 4
page 5-7
page 7
page 7
battery holder
page 8-10
A bag+B bag + D bag + printing paper
B bag + D bag +printing paper
C bag +D bag + printing paper
A bag+B bag + D bag + printing paper+ template paper
D bag + E bag
C bag + D bag+ template paper
A bag +C bag+D bag +printing paper+ template paper
E bag
range hood A bag + B bag + printing paper
2
dust cover page 11
Z bag+D bag
Contents
Name Materials package
A bag A05,A06(all of printing paper and template paper are in A05,
A06;total 4pieces of A5 paper )
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B

1 2 3
4 5 6 7 8 9
10 11 12
2 3 4
B01
B02 B03
B04
A04-1 A04-1
A05-04
A05-02 A05-03 A05-05
A04-2 A04-2
D10
A04-2
A04-2
A04-1
A04-1 A05-04
Paste around
D07 D07
D10
B01B02
1
1
B10 B11
B12 A05-06 A05-07
D18
B03
B03
B04
Paste as shown.
Paste as shown
B11
B12 B12
B10
B11
A05-06
Make two according to
the previous step.
A05-02 A05-03
Rolled up to dotted
line position
A05-05
0.7cm 1.5cm
2
2
1
22
B11
B11
D07(4pieces)
3
Refrigerator
B03
D10
B11
Rack

8 9 10
11 12
3 4
complete photo
Glue fixing
Place and paste as
shown in the figures
Fold according to the
structural line.
1 2
1.2cm
A05-09 A05-10
B08 B09
A04-04
Paste as shown to
complete the drawings
C01
C02 C03(2pieces)
C04 C05 C06
D16(4pieces)
A05-11
5 6 7
3
1 2
D18
A05-07
13 14
A05-09 backside
A04-04
B08
C01 D16
C02
3
3
2cm
0.8cm
1cm
A05-06 backside
A05-10
A05-06
D18
D18
A05-07 A05-07
A05-07
A05-09
A05-09
B09
D16
D16
4
complete photo
Glue fixing
Range hood Kitchen utensil

4 5 6
4 5 6
7 89
B05 B07
B06
A05-12 A05-13
D18 D19
D16
(2pieces)D17
D04
(2pieces) D05 D06 D07 D08 D09 D11 D12
(2pieces)
D13
(3pieces)
A05-15
Paste as shown to
complete the drawings
A05-18
A05-19
A05-17
D20
A05-16 A05-20
1 2 3
A04-03
7
The reflective surface is rolled
around, and the adhesive
surface is 0.3cm
C03
C03
A05-11
A04-03
A05-15
A05-16
D04
D04
D03-2
D03-1 A05-17
D09
D18
2cm
C05
C04
C06
8
Affix D03-2 to D03-1.
4
Before making, cut out D01, D02 and D03 according to A06-D01
A06-D02A06-D03 template paper
D03-1
D03-2
D03-3
D02-1
D01-2
Paste around the edge
of A04-03 with A05-16
5
A05-11
Paste as shown
A04-03
A04-03 A04-03
A04-03
D03-2
5
Cut out A05-11 and paste
it as shown in the figures
Cupboard &
Kitchen utensil
B06

10 11
19 20 21
12
24 25 26 27
30 31 32 33
13 14 15
16 17 18
22 23
28 29
D18 D05
D03-3
D08
D16
D17
A05-19
D07
D11 A05-18
D20
D13 D13 D13
D12 D12
D06
A05-20
B05 B07
B06
B06
B06
D19
D16
D18
Pick 5 leaves of D20.
D20
Paste on D06.Paste as shown.
2.1cm
0.3cm
1.6cm
D18
0.3cm 0.3cm
6
7
8
2cm
1.4cm
0.5cm
Fold according to the
structure line and paste.
0.8cm
0.9
D01-2
D05
D20 D20
A05-20
A05-20
D19 D19 D18
D18
This surface is a
non-reflective surfaces.
1.3cm
6
A
B
complete photo

34 35 36 37 38
2
1
1 2 3 4
D14(2pieces) D15(2pieces)
E01(2pieces )
Place and paste as shown in the figures.
3
D02-1
E01
D15 D14
A05-13
Complete 3 according
to the previous step.
8
4
56
7
A05-12
Fold according to the
structural line.
2.8cm
D18
D18
0.4cm 0.4cm
1.8cm D02-1 Fold in half and put
D18 through the middle at
the pasting edge.
D18
Paste as shown.
3.6cm
1.5cm
Need to make two
39 40 41
C07
D01-1 5cm
6.3cm
Fold twice and fix with glue.
1.2cm C07
D01-1
complete photo.
Attach C07 to D01-1.
Note the edge.
D02-1
9
9
A05-12
Before making, cut out D01 according to
A06-D01 template paper.
2.7cm
Paste A05-13 into the hole of B05.
Paste as shown.
D01-1
5cm
42 43
1.2cm
D01-1
A05-20
D18
B05
A05-13
A05-13
7
Wall lamp Curtain

white
edge
white eged
A01
A03
A02
A05-14
A05-08
A05-01
1 2 3
4 5
A01
A02 A03
6
8
Empty window A05-14.
Outer frame
white
edge
white
edge
white
edge

7 8 9
10 11 12
A
B
A
B
C08
Put the lamp wire through the hole to install the
lamp on the wall with glue.
Paste to the appropriate location.
D02-2
curtain
rack
range hood
cupboard carpet
kitchen
utensil
Cut out D02 according to
A06-D02 template paper.
D02-2
A03
A01
A02
A01
carpet
9

1
E03
E03
2 3
E03
refrigerator
13
E02
4
10
How to assemble the
battery holder
Statement: the lamp wires cannot be inserted into
the output socket.
– – Can use 2*AAA batteries
– – Please notice the place of anode
and cathode when pit in the batteries
– – Rechargeable batteries are not blunt electricity
– – Rechargeable batteries can only be charged
under adult supervision
– – Rechargeable batteries should be
removed from the toy before charging
– – Different types of batteries cannot mix; Do not
mix new batteries in use with semi-used batteries.
– – Run out of battery should be removed from the toy
– – The power shall not be short circuit
cut all the LED light wires to the same length
peel off the film of the LED light wires
and then wrap it together in the same color.
Twist the following wire together:
(I) BLACK wire from the battery box with the WHITE
wire from LED bulb.
(II) RED wire from the battery box with the GREY
wire from LED bulb.
Wrap the bare wires with adhesive
tape E03.Make sure the LED lights are on.
Tie the lamp wires together with E03 adhesive tape.
E03
E03

11
Dust cover
scale:1:6
Z01 plexiglass(transparent)
13*13*0.13cm(1piece)
scale:1:6
Z02 plexiglass(transparent)
12.5*11*0.13cm(1piece)
scale:1:6
Z03 plexiglass(transparent)
12.37*11*0.13cm(1piece)
Z03
Z02
Z01
Z01
E03
E03
Z03
Z02
E03
E03
E03
(outside view)
Z01
Z02
Z03
(inside view)
1
2
3
4567
A
B
Z01
Z02
E03
E03
E03
Z02
A
B
Installation of dust cover
(plane display drawing)
stick Z02 and Z03 on Z01
Ripped one side of kraft paper,
leaving one side of kraft paper
Take out the plexiglass and tear off the
kraft paper with text on each piece of
plexiglass
(This side of kraft
paper not torn,
facing outward)
(This side of kraft
paper has been
torn,facing up)
The kraft paper that has been ripped off
faces inwards, and the kraft paper that
has not been ripped out faces out wards.
Place Z01 to the right at a right angle of
90 degrees to Z02
Use E03 to fix the junction of two pieces
of plexiglass, (use transparent tape to
replace E03)
(This side of kraft
paper not torn,
facing outward)
The junction of every two pieces of plexiglass
needs to be fixed with E03 (to prevent the
plexiglass falling off)
stick appropriate amount of glue to the interface of the
two pieces of glass and scrape it slightly to make the
glue penetrate into the junction of the two pieces of
glass (the red line is theplexiglass interface)
Leave it for 1 hour. After the glue dries out,
tear off a layer of kraft paper outside the
plexiglass.
leave 0.5cm
(Internal inverted transparent view)

12
12
Great!It had finished!
It can be combined with other designs,
would you like to see them?
Photo of Dust proof cover

13
Photos with roof
(Roof need to purchased separately)
Two-in-one
(Photos for reference,can be combined in different by yourself)

14
Three-in-one
(Photos for reference,can be combined in different by yourself)
Four-in-one Four-in-one
(Photos for reference,can be combined in different
by yourself)(Photos for reference,can be combined in different by yourself)

The instruction manual should be keep,after assembled
(Photos for reference,can be combined in different by yourself)(Photos for reference,can be combined in different by yourself)
Nine-in-one
Six-in-one