Hongda USA S2131 User manual

S2131 Instruction manul
S2131
Dream ParadiseDream ParadiseDream Paradise

12
Tips for assembling
1.Because this product contains small parts, children need to use this product with an adult to avoid accidental ingestion and cause suffocation hazard.
There are sharp objects in the product, be careful not to pierce people to avoid injury.
2.After all the materials are used in the required amount in the operation steps, put the remaining materials back into the original bag until the installation is completed.
(Avoid losing materials during the installation process)
3.The unit of dimension marked in the step diagram is "cm".
4.Tips for making template paper: Put the template on the back of the material, fix it with some small double-sided tape, and then cut out the material to prevent the
cloth or template from moving in the cutting process, or causing errors in the cut material. Or lead to insufficient materials.
5.According to the "Parts Rule Example" at the bottom of this page, refer to the parts on the part number drawing, find the actual product and compare it with the bill
of materials, and then install it after confirming that it is correct. (Wooden parts only)
6.It is not advisable to apply too much glue, so as not to wait for a longer time to dry, and overflow will affect the effect of the finished product.
7.There are unavoidable small deviations in the color of wood, fabric, and beads of different batches, without notice, thanks for understanding.
Tips for Assembling Wood
Find the corresponding block number,
use a knife in the connection point
gently press, you can take out the wood.
Use a knife to
smooth out the burr.
Or use sandpaper to smooth
out the burr
Be sure to test the LED lights before making the lighting,note that the LED
white wire to the negative, gray wire to the positive reference to the
following figure operation test.
Testing on LED function
DO NOT contact the
LED wire end direct
to the battery cell.
Use the provide battery
holder. Make sue the
correct polarity.
How to assemble the battery holder
1.Material and tools needed:
- Battery holder, LED bulb,
tape, screw driver and 2 pieces
AAA size battery(not provided)
2. Use screw driver and
take the lid off from the
battery holder.
3. Insert the battery take
notes on the polarity.
4. Connect the red wire
to grey wire. Connect
the black wire to white
wire.
5.Wrap the exposed wire
with the tapes.
6. Place the box lid and
fastness with screw driver.
A01:The parts are directly in the box: B01: The parts are in the B bag; C01: The parts are in the C bag, and so on (Note: The printing paper is displayed in the step A07-01:
The printing paper is placed directly in the box , The part number is A07-01. In the step, the template paper A07-C01 is displayed, A07 is the template paper,
D01 is the cutting template used for the corresponding material, D01-01, D01-02 are the part numbers for the parts, and the printing paper and template paper
are directly placed in the packaging box.)
Examples of parts rule:
“-”negative
“+”positive
1

Name Materials Bags
printing paper
&template paper
A bag A11,A12（all of printing paper and templete are in
A11,A12,total 4 pieces of A5 paper)
A bag+B bag+E bag+F bag+printing paper
page 3-4
C bag+E bag+F bag
page 5-6
C bag+F bag+G bag+printing paper
page 6-7
D bag+printing paper
page 7
D bag
page 7
D bag+F bag+printing paper
page 8
page 8
2
page 4-5
A bag+ F bag+G bag+printing paper
steps and fliowers
D bag+E bag+printing paper
D bag+E bag
page 8
spinning plane
base of
spinning plane
ferris wheel
base of ferris wheel
gate&guide board
bench
hobbyhorse
street lamp
D bag+printing paper
page 7
beach umbrella
D bag
windmills
ice cream van
A bag+D bag+E bag+printing paper
page 9-10
page 11
balloon
E bag+F bag
page 11
coloured flags
E bag+F bag+printing paper
outer frame
batteries box
A bag+B bag+E bag+F bag+G bag+printing paper
+templete paper
G bag
page 11-15
page 15
page 11
Material List Thumbnail (For Reference Only)
Printed paper and template paper thumbnail (For Reference Only )
Table of Contents
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B

3
2
43 4
10
11 13 14 15 16 12
1
1
B11
B12
( 2 pieces)
B13
B14
( 2 pieces)
B15
B03 B04 B05 B06 B07
B08
( 2 pieces)
B09
B10
( 2 pieces)
B16 ( 8 pieces)
B17 ( 4 pieces)
A07-1
A07-2 A07-3 A07-4 A07-5
A11-1
A11-2
A11-3
A11-4
A11-5
A11-6
A11-7-1 A11-7-2 A11-8-1 A11-8-2 A11-9-1 A11-9-2
A11-10-1 A11-10-2 A11-11-1 A11-11-2 A11-12 E06
56789
Spinning plane
A11-1
Bend the printing paper
as picture
A07-1
A07-2
A11-2
A07-3
A11-3
A07-4
A07-4
A07-3
A11-3
A07-5
A07-4
A11-4 A11-5A07-5
A07-5
Wrap the A07-1,A07-2
with A11-1 as shown
1
23
4
2
1
3A11-12
F03:1.5cm

4
17 18 19 20 21 22
23 24 25 26 27 28
29 30 31 32 33
Base of
spinning plane
A07-6 A11-13-1
A11-13-2
A11-12
F03:1.5cm
A11-6
E06
B03
B07
B06
B04
B05
A11-7-1
B08
A11-7-2
B08
B16
B09
B16
B17
A11-11-1
A11-11-2
F09 F09 F09
G09
4
Make 3 pieces according to the previous steps
B17
B17
B17
A11-8-1A11-9-1A11-10-1
B15
B13
B11
B08
B08

123456
C01
C01
C02
C02
C03 C03
C04
C04
C05
C05
C06
C07(4 pieces)
C08(2 pieces)
C09(4 pieces)
C10(2 pieces)
C11(4 pieces)
C12(2 pieces)
C13(4 pieces)
C14(2 pieces)
E10 ( 18 pieces)
E11( 8 pieces)
E12( 8 pieces)
C15(8 pieces)
F01 :72cm
12
34
5
A07-6
A11-13-1
G09
(Turn over the A07-6)
F09 F09
F09
Screw on
A11-13-2
C11
C12
(Turn it over)
Make 2 pieces according to the previous steps
C11
Ferris wheel
5
C07
C08
C10
C09
C11
C12
C14
C13

6 10
789 11
13 14 15 16
12 17
201918
G02
21 22
F01:1.5cm(7 pieces)
C17 A11-14-1
A11-14-2
C16 123
C01
C02
C03
C04
(Need 2 pieces)
F01 :22cm E10 E10
E10
E10
E10
E10
E10
E10
E11
E11
E11
E11
E12 E12
E12
E12
F01 :14cm
C05
(Need 2 pieces)
C06
5
5
C15
C15
C15
C15
C15
C15
C15
C15
5
6
6
E10
Base of ferris wheel
C17
A11-14-1
A11-14-2
6
Stick with E10 in each side

Spinning aircraft
Merry go round
Roller Coaster
Ferris wheel
45678 9
Gate&
guide board
12345
D01
D09
A11-15
A11-16-2
A11-16-1
12345
Bench Beach umbrella
D03(4 pieces)
D02(4 pieces)
123
D12 D13
D15
D16
A11-18 A11-17
G02 C16
C16
F01:1.5cm
C16
F01:1.5cm
D09
A11-16-1
A11-16-2
D01
A11-15
D02
D03 D03
D02
(Need 2 pieces)
A11-18
D15
D13
0.5cm
A11-17
D16
D12
(Please test the light before
assemble)
7

D04
D05
A11-19-1 A11-19-2
A11-19-3
A11-20-1 A11-20-2
A11-20-3
F03:13cm
123
5
4678 9
Hobbyhorse
E06 E06 E06
D14
D15
D15
A11-21 A11-21 A11-21
123
E05 ( 6 pieces)
D17 D17
123
Street lamp Windmill
A11-20-1
D05
A11-20-2
(The front side)
F03:6.5cm
A11-20-3 A11-19-3
A11-19-2
D04
Make the other one
as previous steps
Wrap the F03 around
the D14 as picture
E05
D17
E05 E05
(Need 2 pieces)
D15
A11-21
E06
D15 D15
D14
8
(The back side)
(Need 2 pieces)F03:6.5cm F03:6.5cm

Ice cream van
A07-7
A07-7
A07-8
A07-9
A07-10
A07-11
A07-11 A07-12
D10 D11 D11
A11-22
A11-23
A11-24 A11-25
A11-26-1
A11-26-2
A11-27-1
A11-27-2
A11-27-2
A11-28 A11-28
A11-29
1235
46
78 9 10 11 12
A07-7
A11-23
A07-7
A11-22
A07-9
A07-8
78
8
Turn over
8
7
7
8A11-24 A11-25
Fold the printing paper
as shown
Fold the printing paper
as shown
A11-26-1
A07-10
E13
9

13 14 15 16 17 18
2019 21 22 23 24
2625 27 28 29 30
3231 33 34 35
A11-26-2
A07-11
A11-27-2
10
9
A07-12
A11-27-1 A11-27-1
10
10
A11-28
Fold the printing paper
as shown
Fold the printing paper
as shown
(Need 2 pieces)
A11-29
Fold the printing paper
as shown
E13
D10
D11
D11
10
(Need 2 pieces)

D06 D06
D07D07
D08 D08
12
Steps
Flowers
F03:5cm
(6 pieces)
F03:6cm
(2 pieces)
Balloon
12
E01 E02
E04 E03
E01 E02
E04
F03:3cm
(2 pieces)
E03
34
E01
F03:6cm
F03:5cm F03:5cm
F03:5cm
E02
E03
E04
F03:3cm
1234
56
A11-30
Coloured flags
F02 :10 cm
F03:5cm
(5 pieces）
Bend according
to A07-13
E06
D06
D07
D08
E02 E02
F03
Wrap the F03
around the D14
as picture
(Need 2 pieces)
F03:5cm
F03:5cm
F03:5cm
F03:5cm
F03:5cm
Repeat the previous steps
F02 :10 cm
3cm
3cm
4cm
Fix F03 on the F02
A11-30
E06
Stick the A11-30 on the F03
as shown
Fix together with E06
11
12
F06
F06
E02
(Need 2 pieces)
1cm
Wrap the E02 with
F06 as shown, the
diameter
is 1cm
(Need 2 pieces)

1234
5678
9 10 11 12
A11-31
A01 (Pay attention to the position
of hole A01 when sticking printing paper)
Hollow out the holes of
the printing paper
F07-1F07-2
F07-3
F07-4
F08-1
Cut out F07 according to the
template paper, and then glue it
as shown
F08-2
F08-3
F08-4
F08-5
F08-6
F08-7
F08-8
Cut out F08 according to the template paper,
and then glue it as shown
Ferris wheel
G01
G01 G01
Put the G01 on the picture
E07 E07
E07
Stick with E07
A02
A07-14
A07-14
11
(Test the light before assemble)
12
G06
G08
G08
G08
G07
A07-14
A07-14
outer frame

13 14 15 16
17 18 19 20
21 22 23 24
A07-14
A05
A05 is flush with A07-14 at the bottom
A05
A05 A03
A08-1 A08-1
A08-1A08-1 11 A04
B01 B01
B01
B01
Base of
spinning plane
Screw the base of the rotating aircraft
counterclockwise inside the movement
spinning plane
Cut the F02 into 5 sections of 2.5cm
and then bend it according to template A07-15
F02:2.5cm
1.5cm
0.5cm
(Need 5 pieces)
13

25 26 27 28
29 30 31 32
33 34 35 36
E09
E08 E08 E08 E08
E09 E09 E09
Steps
Colored flags
F04
Bench
Bench Hobbyhorse
Balloon Flowers
Street lamp
Street lamp
Windmills Windmills
Ice cream van
F05
F05
F05
Beach umbrella
B02 Cut all the wires to the
same length
Peel off the film at the end,
and then twist the copper wire
part together
14

A
B
A07-16
A07-17
A07-18
A
B
A07-17
A
B
A06
37 38 39
40 41 42
47
43
44 45 46
48
G03
Put the battery box in the drawer of the battery box
Put the wire through the drawer of the battery box
G05
15
A06
2mm
A07-17
Glue A06 as shown in the picture
LED light white wire
LED light gray wire
battery box
black wire
battery box
red wire
How to assemble the
battery holder
Statement: the lamp wires cannot be inserted into
the output socket.
– – Can use 2*AAA batteries
– – Please notice the place of anode
and cathode when pit in the batteries
– – Rechargeable batteries are not blunt electricity
– – Rechargeable batteries can only be charged
under adult supervision
– – Rechargeable batteries should be
removed from the toy before charging
– – Different types of batteries cannot mix; Do not
mix new batteries in use with semi-used batteries.
– – Run out of battery should be removed from the toy
– – The power shall not be short circuit
battery box
red wire
battery box
black wire

Ratio:1:10
Z01 plexiglass (transparent)
20*13*0.18(1piece)
Ratio:1:10
Z02 plexiglass (transparent)
14.5*12.64*0.18(2pieces)
Ratio:1:10
Z03 plexiglass (transparent)
20*14.5*0.18(2pieces)
Z03
Z02
Z03
Z02
Z02
Z01
1 2 3
6 7 84 5
11 12 139 10
A
B
A
B
A
B
A
B
G05
Z02
Z03
Z03
Z01
G05
G05
Z01
Z03
Z01
Z03
G05
G05
G05
G05
Z03
Z02
Z01
Z03
Z02
G05
G05
G05
G05
Z03
Z02
Z02
Z03
Z03
Z01
G05
G05
G05
Z02
Z03
Z01
Z03
Z03
Z02
Z02
16
Installation of dust cover
stick five pieces of plexiglass dust
cover as shown
Take out the plexiglass and tear off the
kraft paper with text on each piece of
plexiglass
Ripped one side of kraft paper,
leaving one side of kraft paper
The kraft paper that has been ripped off
faces inwards, and the kraft paper that
has not been ripped out faces out wards.
(This side of kraft
paper not torn,
facing outward)
Use M03 to fix the junction of two pieces
of plexiglass, (use transparent tape to
replace M03)
The junction of every two pieces of
plexiglass needs to be fixed with M03
(to prevent the plexiglass falling off)
stick appropriate amount of glue to the interface
of the two pieces of glass and scrape it slightly
to make the glue penetrate into the junction
of the two pieces of glass (the red line is the
plexiglass interface)
stick appropriate amount of glue to the interface
of the two pieces of glass and scrape it slightly
to make the glue penetrate into the junction
of the two pieces of glass (the red line is the
plexiglass interface)
dust cover
(Upgrade version accessories need
to be purchased separat ely)
stick Z02 and Z03 on Z01.
(This side of kraft
paper has been
torn,facing up)
(This side of kraft
paper not torn,
facing outward) (This side of kraft
paper not torn,
facing outward)
The junction of two pieces of plexiglass
needs to be fixed with M03(to prevent
the plexiglass falling off)
(This side of kraft
paper not torn,
facing outward)
The junction of two pieces of plexiglass
needs to be fixed with M03
(to prevent the plexiglass falling off)
stick appropriate amount of glue to the interface
of the two pieces of glass and scrape it slightly
to make the glue penetrate into the junction
of the two pieces of glass (the red line is the
plexiglass interface)
the dust cover need to be glued
8 interfaces
Leave it for 1 hour. After the glue dries out,
tear off a layer of kraft paper outside the
plexiglass

17
Sence Display

18
Details Display

Combination display
The instruction manual should be keep,after assembled