Hored PS2010G User manual

User manual
PS2010G
8 Port Gigabit Layer 2 PoE Switch

1
Installation manual introduction
The Product installation manual mainly describes PS2010G PoE switch
hardware features, installation methods, and precautions during the
installation
This manual includes the following chapters:
Chapter 1: Product Introduction. Briefly describes the basic features,
Detailed hardware & software specifications of the switch and the
appearance details.
Chapter 2: Product Installation. Guide the switch hardware installation
methods and precautions.
Chapter 3: Hardware Connections. Guide the connection between
switches and other devices and precautions.
Chapter 4: Packaging and product usage suggestions.

2
Chapter 1: Product Introduction
1.1 Products description
PS2010G is managed PoE switch for security transmission and
WIFI coverage, meet the need of PoE power supply for WIFI AP,
IP-camera, WIFI bridge, IP phones and other types of equipment.
New generation of high-performance hardware and software
platforms are used, providing flexible, cost-effective full Gigabit
access and uplink ports, complete security mechanisms, improved
ACL / QoS strategy and rich VLAN capabilities. It is easy to
manage and maintain, meet the users' requirements for network
equipment easy to manage, high security and low cost.
Supporting Apollo Cloud One-stop Management Platform,
realizing status checking and management monitoring functions,
suitable for campus, Hotel and enterprise park network access,
convergence, core application scenarios.
1.2 Product Features
1-8 port support 250Meters long-distance power supply
(recommended cat5e or 6 network cable)

3
Support a key VLAN, the port 1-8 isolated from each other, which
can effectively inhibit network storms, improve network
performance
Supports IEEE 802.3af / at standard, automatically detects and
identifies devices that comply with the IEEE 802.3af / at standard
and supply power to it
Support Auto MDI/MDIX；
Adopt store-and-forward exchange method
intelligent power supply, the lowest power consumption, ensure
PD power needs
With power circuit protection, protect the safety of PD
No configuration characteristics of the power supply is
automatically supplied to the adaptive equipment;
Fan-less design, energy saving and environmental protection; no
noise, reduce the impact on the environment.
Support Apollo Cloud Platform One-stop Management, Realizing
Visual Management of Switches and connected devices, making
Operations and Maintenance Simpler.
Small, exquisite design

4
Plug and play,no configuration required, easy to use.
1.3 product specification
Hardware Specifications
Chipset
RealtekHigh Performance Chipset
Flash
16MB
RAM
128DDR
Port
8 10/100/1000Mbps RJ45 ports
2 Gigabit SFP fiber ports
1 Console port
PoE
8 10/100/1000Mbps RJ45 port support
PoE
Max 150W
Single port max 46W
LEDs
10 Link/Act LEDs
8 POE LEDs
1 Power LEDs 1 SYS LED
Performance
Forwarding mode: store and forward
Switch Volume (Full-duplex) ：20Gbps
Packet forwarding rate：14.88Mpps
8K MAC address table
lightning protection
±4KV
ESD
No barrier: ±6KV Air：±8KV
Input
100-240V/50-60Hz
Dimension
（L×W×H）
285mm×180mm×44mm

5
Software Specifications
Network standard
IEEE 802.3: Ethernet Media Access Control
(MAC) protocol
IEEE 802.3i:10BASE-T Ethernet
IEEE 802.3u:100BASE-TX fast Ethernet
IEEE 802.3ab:1000BASE-T gigabit Ethernet
IEEE 802.3z:1000BASE-X gigabit Ethernet
（fiber）
IEEE 802.3ad: comply link aggregation
standard
IEEE 802.3x: flow control
IEEE 802.1p: About the traffic priority of
the second layer of Qos / Cos protocol
(multicast filtering)
IEEE 802.1q:VLAN Bridge operation
IEEE 802.1d:STP spanning tree
IEEE 802.1s:MSTP spanning tree
IEEE 802.1w:RSTP spanning tree
IEEE 802.3af
IEEE 802.3at
Shortcut function
One key VLAN
One key Exnted(1-8 port 250meters PoE
distance)
One key QoS (Video priority)
One key AI power supply
DHCP
Support DHCP Snooping

6
VLAN
Support 4K VLAN
Support 802.1Q VLAN、Port VLAN、Voice
VLAN
MAC address table
Comply the IEEE 802.1d standard
Support MAC address learning and aging
automatically
Support static, dynamic, filter address table
Safety
Password protection
Support based on the port number, IP
address, MAC address restrictions on user
access
Support HTTPS、SSL V3、TLS V1、SSH
V1/V2
Based on user rating management and
password protection
Support IP-MAC-PORT
Support ARP protection, IP sources
protection, DoS protection
Support DHCP Snooping、DHCP attack
protection
Support 802.1X AAA
Support port security, port isolation

7
Support CPU protection
PoE
Support setting the PoE port priority
Support viewing POE Chip Status
Support setting PoE power supply period
Support setting port power
Access control (ACL)
Support L2(Layer 2)～L4(Layer 4) packet
filtering function
Support port mirroring, port redirection,
flow rate limit, QoS re-marking
QoS
Support 8 port queue
Support port priority, 802.1p priority, DSCP
priority
Support SP、RR、WRR、WFQ Priority
scheduling algorithm
Support automatically identify, manage
and acquire of connected equipment
information
Multicast
Support IGMP v1/v2 Snooping
Support static multicast
Support multicast VLAN
Spanning Tree
Support STP(IEEE 802.1d)，RSTP(IEEE
802.1w) and MSTP(IEEE 802.1s) protocol
Support loop protection, BPDU protection
Storm suppression
Support for multicast suppression

8
Support broadcast suppression
Storm suppression
Support for unknown unicast suppression
Link aggregation
Support static aggregation
Support dynamic aggregation
Support IP, MAC, hybrid load balancing
mode
Supports up to 32 aggregation groups
Management and
maintenance
Support WEB management（HTTP、
HTTPS、SSL V3）
Support CLI（Telnet、local serial port）
Support SNMP V1/V2/V3
Support LLDP、RMON
Support ARP Protection, IP Source
protection、DoS protection
Support CPU monitor、memory
monitoring
Support system log
Support Ping, Tracert detect cable testing

9
1.4 Appearance
Front Panel
Including indicators, RJ45 port, DIP switch, RST button, SFP port,
CONSOLE port, as shown below
indicator
PS2010G The indicator working status is shown as the
following table
Indicators
Title
Color
Wor
k
statu
s
Description
POWER
Power
indicat
or
Red
Solid
Power is normal
Off
No power, the power
switch is not turned on,
power supply is
abnormal
Yellow
Solid
The corresponding RJ45

10
POE
PoE
power
indicat
or
port is connected to the
powered device and the
power supply is normal
Off
The corresponding RJ45
port is not connected to
the powered device or
the power supply is
abnormal
LINK/ACT
Conne
ction
indicat
or
Green
Blink
ing
A valid link is
established
Off
An invalid link is
established
SYS
System
indicat
or
Green
Blink
ing
System is functioning
properly
Off
System is functioning
improperly Software is
damaged
9-10
SFP
indicat
or
Green
Blink
ing
A valid link is
established on the SFP
port
Off
An invalid link is
established on the SFP
port
Shortcut button
QOS: Improve video data processing capabilities and
improve the monitoring of Caton and Mosaic
phenomena in the network

11
Extend: 1-8 port rate down to 10Mbps, but the
transmission distance up to 250 meters
VLAN: Isolating ports 1-8 from each other, suppress
network storms effectively and improve network
performance
AI power supply: Detect PD, power failure and restart
dead equipment
RJ45 Port
PS2010G with 8 10/100/1000Mbps PoE port, all ports
support IEEE802.3af and IEEE802.3at standard
When the switch mode of operation is CCTV mode, 1-8
port can support 250 meters power supply
SFP Port
PS2010G provides 2 Gigabit SFP optical ports (SFP1,
SFP2), can be inserted into the Gigabit SFP module
RST Button
When the switch is powered on, press the button with
the needle to release the device and enter the
restarting state. When the SYS lamp restarts, the device
restarts. When the switch is powered on, press and hold
the button for more than 5s to release the button and

12
enter the reset state. When SYS is re-lit, the device is
reset successfully
Console port
Console port used to connect to computer or other
terminal to manage or configure the switch.
Back Panel
Including: power socket, ground terminal
Power socket
A 100-240VAC 50/60 Hz power receptacle for
accommodating the supplied power cord
Ground terminal
Please use the grounding wire to prevent lightning. To
avoid product lightning strikes and extend product
life

13
Chapter2 Hardware connection
2.1 RJ45 port connection
Connect the RJ45 port of the switch and the corresponding network
device via cables, the POE power supply function of the switch is
default enabled on the downlink port of the switch, which can be
used for IEEE802.3af or IEEE802.3at standards powered devices such
as APs, bridges, and network cameras
Note：
When the switch connected workstations, servers, routers or
other ethernet devices the cable length should be within 100
meters;
The Auto-MDI / MDIX ethernet interface is enabled by default.
Category 5,the standard network cable or crossover cable can be
used for Ethernet connection.

14
Do not connect the RJ45 port to the phone line
2.2 SFP Port connection
PS2010G SFP port only support Gigabit fiber module.
Recommended use of standard SFP module products
The process of installing a fiber module on a switch is as follows:
First, grasp the optic fiber module from the side, insert it
smoothly along the SFP port slot until the optic fiber module and
switch are in close contact;
Second, confirm the Rx and Tx ports of the fiber module when
connecting, insert one end of the fiber into the Rx and Tx ports
correspondingly, ensure that the Tx and Rx ends of the interface
are connected correctly and the other end of the fiber is
connected to another device;
Third, please check the corresponding indicator light status after
power on. If the light blinking that the link is properly connected,
if the light is off , the link is failure, please check the line to
confirm that the corresponding equipment is enabled.
Note：
DO NOT excessive bending fiber, the radius of curvature should
not be lessthan 10cm;
Ensure the cleanliness of the fiber surface;
Please DO NOT look directly into the optical fiber connector with
your eyes as this may cause eye injury

15
2.3 Check before power on
Check whether the outlet power supply meets the switch
specifications;
Check the power, switches, racks and other equipment have been
properly grounded;
Check whether the switch and other network devices are
connected properly
2.4 Device initialization
The switch automatically initializes when the power switch is
turned on.
Indicator will appear the following situation:
After the power is turned on, the power indicator remains on, the
other indicator is off at this time;
After about 1 second, all lights except for the power light turn on
for about 35 seconds and then turn off; when the SYS light goes
flashing, the system runs normally
Port LEDs indicates the connection status of each port, indicating
that the switch has started to work normally

16
Chapter3 Installation
3.1 Installation Precautions
Note：To avoid improper use of equipment damage and
personal injury, please observe the following precautions
Installation safety precautions
The power should be kept off during the installation, while
wearing anti-static wrist, and to ensure well touch between
anti-static wrist and skin to avoid potential safety hazard;
The switch just works normally when it is powered by the
correct power supply. Make sure that the power supply
voltage matches the voltage indicated by the switch
Before powering on the switch, make sure that the power
circuit is not overloaded, which may affect the normal
operation of the switch and even cause unnecessary damage
To avoid the risk of electric shock, do not open the case while
the switch is working. Do not open the case even when it is
not powered
Before cleaning the switch, unplug the switch from the power
cord and do not wipe it with wet cloth. Do not wash it with
liquid
Temperature and humidity
To ensure the long-term stability working of the switch , please
maintain a certain temperature and humidity environment.

17
High or low humidity easily lead to leakage of insulation
materials, deformation and even the corrosion of metal parts,
the temperature is too high will accelerate the aging process
of insulating materials, seriously affecting the service life of
equipment. The normal operation of this series of switches
and storage temperature / humidity are as follows
Environmental
description
temperature
Relative humidity
Working
environment
0℃~40℃
10%～90% RH no
condensation
Storage
environment
-40℃～70℃
5%～90% RH no
condensation
Altitude
Products with this logo are only for safe use in areas below
2000m altitude
Dust-proof
Dust on the switch surface will cause electrostatic adsorption,
poor contact of the metal contacts. Although the device itself
has done some measures in anti-static, but when the static
electricity exceeds a certain intensity, it will still cause fatal
damage to the electronic components on the internal circuit
board.
In order to prevent static electricity from affecting the normal
operation of the equipment, please note the following:

18
1. Regular dust, keep the indoor air clean;
2. Make sure the equipment is well grounded to ensure
smooth transfer of static electricity
Electromagnetic interference
Electromagnetic interference have an impact on the device
capacitance, inductance and other electronic components by
capacitance, inductive coupling, impedance coupling and
other conductive, in order to reduce the adverse effects
caused by electromagnetic interference, please note the
following：
1. Power supply system to take the necessary anti-grid
interference measures;
2. Switches should be far away from high-frequency high-
power, high-current devices, such as wireless
transmitters;
3. If necessary, take electromagnetic shielding measures
Lightning protection
When a lightning strike occurs, a strong current will be
generated in an instant cause fatal damage to electronic
equipment. To achieve better lightning protection, please note
the following：
1. Make sure the rack and the ground to maintain good
contact;
2. Make sure the power outlet is in good contact with the
earth;

19
3. Reasonable wiring, to avoid the internal sense ray;
4. Outdoor wiring, it is recommended to use the signal
lightning protection device
Installation desk requirement
Regardless of whether the switch is installed in a rack or on
another horizontal workbench, be aware of the following:
1. Make sure the rack or workbench is stable, strong, and
can withstand at least 5.5Kg weight;
2. Make sure the rack has a good cooling system, or
maintain good indoor ventilation;
3. Make sure the rack is well grounded, the power outlet
and switch are within 1.5 meters
Prepare tools for installation
You may need to use a screwdriver during installation, electrostatic
wrist strap, fiber optic cable and other tools to prepare your own