Horizon Fitness 832T User manual

TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
822T832T

23
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to
the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your elliptical’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
WARNING
SERIAL NUMBER:
MODEL NAME: HoRIzoN TREADMILL

4 5
READING RACK
GR IP PULSE H AND R AIL S
WATER BOTTLE HOLDER
ON /OFF SWITCH
CIRCUIT B REAK ER
TR ANSPORT WHE EL
POWER C ORD
CONS OLE
SAFE T Y KEY PL ACE MENT
RUNNING B ELT / RUNNING D ECK
SI DE RAIL
ROLLER EN D CAP
RE AR RO LLER
ADJU STM ENT BOLTS
CONS OLE MAST
MOTOR COVE R
FOOT LO CK LATCH (UN DERNEATH DECK )
TOUCH PAD PANE L AND D ISPLAY WI NDO WS
SIDE HANDRAILS
SIDERAIL SLEEVES
ALL
MoDELS
TooLS INCLUDED:
F5 mm T-Wrench
FScrew Driver
PARTS INCLUDED:
F1 Console Assembly
F2 Console Masts
F3 Hardware Bags
F1 Safety Key
F1 Bottle of Silicone Lubricant
(for 2 applications)
F1 Power Cord
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack the unit where it will be used. The enclosed
treadmill is equipped with high-pressure shocks and may spring open if mishandled.
Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
PRE ASSEMBLY
ALL
MoDELS

6 7
ALL
MoDELS
ALL
MoDELS
ASSEMBLY STEP 1
A Open HARDWARE BAG 1.
B Slide the left CONSOLEMAST over MAiN
fRAME BRACKET.
C Secare from the back using 2 BOLS(z03),
2 SPRiNG WASHER(z05), and 2 ARC
WASHER(z11).
D Secare from the side using 2 BOLTS(z12),
2 SPRiNG WASHER(z05) and 2 fLAT
WASHER(z04).
E Repeat on the other side.
BOLT (Z03)
15 mm
Qty: 4
FLAT WASHE R (Z04)
8.2 mm
Qty: 4
SPRI NG WASHE R (Z05)
8.2 mm
Qty: 8
ARC WASHER (Z11)
8.4 mm
Qty: 4
BOLT (Z12)
50 mm
Qty: 4
HARDWARE BAG 1 CONTENTS :
LEFT CONSOLE MAST
MAIN FRAME BRACKET
RIGHT CONSOLE MAST
Z04
Z05
Z12
Z03 Z11
Z05
ASSEMBLY STEP 2
A Open HARDWARE BAG 2.
B Gently place the CONSOLE on top of the
CONSOLE MASTS.
C Secure from the side using 1 BOLT(z03),
1 SPRiNG WASHER(z05) and 1 fLAT
WASHER(z04).
D Secure from the back using 2 BOLTS(z03),
2 SPRiNG WASHER(z05) and 2 ARC
WASHER(z11).
E Repeat on the other side.
NOTE: Make sure CONSOLE CABLE is
not blocking any of the bolt holes.
BOLT (Z03)
15 mm
Qty: 6
FLAT WASHE R (Z04)
8.2 mm
Qty: 2
SPRI NG WASHE R (Z05)
8.2 mm
Qty: 6
ARC WASHER (Z11)
8.4 mm
Qty: 4
HARDWARE BAG 2 CONTENTS :
Z03
Z05
Z11
Z03
Z05
Z04
NOTE: Carefully pull console wire
through the RIGHT CONSOLE
MAST. Attach the CONSOLE WIRE
to the pre-attached routing wire.
Discard wire when finished.

8 9
ALL
MoDELS
ALL
MoDELS
ASSEMBLY STEP 3
SPRI NG WASHE R (Z05)
8.2 mm
Qty: 2
ARC WASHER (Z11)
8.4 mm
Qty: 2
BOLT (Z13)
95 mm
Qty: 2
BOLT (Z19)
12 mm
Qty: 6
HARDWARE BAG 3 CONTENTS :
Z13
Z05 Z11
CONSOLE POST
CONSOLE MAST
Z19
HANDRAIL SLEEVE
A Open HARDWARE BAG 3.
B Slide HANDRAiL SLEEVE over the lower end
of the handrail .
C Slide top of HANDRAiL into CONSOLE POST.
D Align bottom of HANDRAiL to bolt hole in
CONSOLE MAST.
E Insert 3 BOLTS(z19) into HANDRAiL as shown
to attach handrail to the console pose.
F Insert 1 BOLT(z13) into 1 SPRiNG
WASHER(z05) and 1 ARC WASHER(z11)
through the back of the console mast to attach
the lower of handrail to the console mast.
G Tighten all console bolts completely.
ASSEMBLY STEP 4
NOTE: There is no hardware bag for this step.
A Connect the CONSOLE CABLES and carefully tuck wires
in MAST to avoid damage.
B Attach CONSOLE CABLE COVER. Connect POWER
CORD to the POWER CORD iNPUT, located at front of
the main frame. Connect CORD to a power outlet. Locate
the ON / Off switch on the back of the CONSOLE.
Flip the switch to the ON position. After a “beep”, the
CONSOLE will light up.
CONSOLE CABLE
COVER
YOU ARE FINISHED!
NOTE: NOTE: DO NOT PINCH CONSOLE CABLE.
Be sure the console cable prongs are aligned and the
ends are tightly seated into each other.

10 11
TREADMILL OPERATION
This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the
TREADMILL GUIDE has instructions for the following:
• LoCATIoN oF THE TREADMILL
• USING THE SAFETY KEY
• FoLDING THE TREADMILL
• MoVING THE TREADMILL
• LEVELING THE TREADMILL
• TENSIoNING THE RUNNING BELT
• CENTERING THE RUNNING BELT
• USING THE HEART RATE FUNCTIoN

12 13
832T
832T CoNSoLE oPERATIoN
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) MoNIToR DISPLAY: Speed, Time, Heart Rate, Distance, Incline, and Calories.
B) START: Simply press to begin exercising or starts your program.
C) SToP: Press to end your workout. Hold for 3 seconds to reset the treadmill.
D) ENTER / CHANGE DISPLAY: Used to confirm selection and scroll between workout information.
E) QUICK INCLINE / KEYS: Press to reach desired incline more quickly.
F) QUICK SPEED/ KEYS: Press to reach desired speed more quickly.
G) INCLINE ARRoW KEYS: Used to adjust incline in small increments (0.5% increments).
H) SPEED ARRoW KEYS: Used to adjust speed in small increments (0.1 mph /0.1km/h increments).
I) QUICK PRoGRAM KEYS: Press key to select program.
J) QUICK TIME KEYS: Press key to select time.
K) QUICK DISTANCE KEYS: Press key to select distance.
* Maximum user’s body weight = 125 kg / 275 lbs
832T
G
I J
B D C FE H
A K

14 15
822T
822T CoNSoLE oPERATIoN
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) MoNIToR DISPLAY: Speed, Time, Heart Rate, Distance, Incline, and Calories.
B) START: Simply press to begin exercising or starts/pauses your program.
C) SToP: Press to end your workout. Hold for 3 seconds to reset the treadmill.
D) ENTER / CHANGE DISPLAY: Used to confirm selection and scroll between workout information.
E) QUICK INCLINE / KEYS: Press to reach desired incline more quickly.
F) QUICK SPEED/ KEYS: Press to reach desired speed more quickly.
G) INCLINE ARRoW KEYS: Used to adjust incline in small increments (0.5% increments).
H) SPEED ARRoW KEYS: Used to adjust speed in small increments (0.1 mph /0.1km/h increments).
I) QUICK PRoGRAM KEYS: Press key to select program.
J) QUICK TIME KEYS: Press key to select time.
* Maximum user’s body weight = 110 kg / 250 lbs
822T
G
I J
B D C FE H
A

16 17
832T/822T DISPLAY WINDoWS
• SPEED: Shown as MPH or KMPH. Indicates how
fast your walking or running surface is moving.
• TIME: Shown as minutes : seconds. View the time
remaining or the time elapsed in your workout.
• HEART RATE: Shown as BPM (beats per minute).
Used to monitor your heart rate (displayed when
contact is made with both pulse grips).
• DISTANCE: Shown as miles. Indicates distance
traveled or distance remaining during your workout.
• INCLINE: Shown as percent. Indicates the incline of
your walking or running surface.
• CALoRIES: Total calories burned or calories
remaining left to burn during your workout.
832T AVAILABLE PRoGRAMS
• MANUAL: Allows “On The Fly” manual speed and incline
changes. Time-based goal.
• INTERVALS: Walk or run at a series of alternating paced
speed levels. Time-based goal.
• MoUNTAIN WALK: Creates the feel of walking over a
mountain. Time-based goal.
• WEIGHT LoSS WALK: Keeps user in their optimal fat
burning zone. Time-based goal.
• HILL WALK: Simulates walking over hills and helps burn
fat at an increased rate. Time-based goal.
• CARDIo CHALLENGE: Tones muscle and provides a
strong cardio workout. Time-based goal.
• ENDURANCE CHALLENGE: Tones muscle and
challenges cardiovascular system. Time-based goal.
• CRoSS CoUNTRY: Improve your cardiovascular system
by lowering resistance to simulate country stroll.
• RoCK CLIMB: Program is for an exciting and
challenging workout. and tones muscles, and challenges
the entire cardiovascular system.
• FAT BURN: Promotes fat burning by raising and
lowering the speed range, while keeping you in your fat
burning zone.
• 100KCAL BURNING: the program will adjust the speed
and incline to burn 100Kcal within your selected workout
time or workout distance. For instance, if you select this
program and select 30 minutes, the program will burn 100
Kcal within 30 minutes. (The program will automatically adjust
the speed and incline. Once you adjust the speed or incline by
yourself, your selected workout time or workout distance will
be relatively longer or shorter.)
• 300KCAL BURNING: the program will adjust the speed and
incline to burn 300Kcal within your selected workout time or
workout distance. For instance, if you select this program and
select 30 minutes, the program will burn 300 Kcal within 30
minutes. (The program will automatically adjust the speed and
incline. Once you adjust the speed or incline by yourself, your
selected workout time or workout distance will be relatively
longer or shorter.)
• 500KCAL BURNING: the program will adjust the speed and
incline to burn 500Kcal within your selected workout time or
workout distance. For instance, if you select this program and
select 30 minutes, the program will burn 500 Kcal within 30
minutes. (The program will automatically adjust the speed and
incline. Once you adjust the speed or incline by yourself, your
selected workout time or workout distance will be relatively
longer or shorter.)
ALL
MoDELS
832T

18 19
832T WoRKoUT PRoFILES MANUAL - User-adjustable Speed and Incline. Start Speed is 0.5 mph / 0.8 km/h.
INTERVALS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Speed(Britsh
2.5 3.0 3.0 4.5 3.0 4.0 3.0 5.0 3.0 5.0 3.0 5.0 3.5 5.0 3.5 5.0 3.5 5.0 3.5 5.0 3.0 5.0 3.0
Speed(Metric)
4.0 4.8 4.8 7.2 4.8 6.4 4.8 8.0 4.8 8.0 4.8 8.0 5.6 8.0 5.6 8.0 5.6 8.0 5.6 8.0 4.8 8.0 4.8
Warm up
22 23 24 25 26
5.0 3.0 4.5 3.0 4.0 3.0 2.5
8.0 4.8 7.2 4.8 6.4 4.8 4.0
Cool Down
(WARM_UP last 2:00 minutes and COOL_DOWN last 2:00 minutes, both of them are included in program times)
MOUNTAIN WALK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Speed(Britsh 2.5 3.0 3.0 4.5 3.0 4.0 3.0 5.0 3.0 5.0 3.0 5.0 3.5 5.0 3.5 5.0 3.5 5.0 3.5 5.0 3.0 5.0 3.0
Incline
0.5 1.0 1.5 2.0 2.0 2.5 2.5 3.0 3.0 3.5 3.5 4.0 4.0 4.5 4.5 4.5 4.0 4.0 3.5 3.5 3.0 3.0 2.5
Speed(Metric)
4.0 4.8 4.8 7.2 4.8 6.4 4.8 8.0 4.8 8.0 4.8 8.0 5.6 8.0 5.6 8.0 5.6 8.0 5.6 8.0 4.8 8.0 4.8
Warm up
22 23 24 25 26
5.0 3.0 4.5 3.0 4.0 3.0 2.5
2.5 2.0 2.0 1.5 1.5 1.0 0.5
8.0 4.8 7.2 4.8 6.4 4.8 4.0
Cool Down
(WARM_UP last 2:00 minutes and COOL_DOWN last 2:00 minutes, both of them are included in program times)
WEIGHT LOSS WALK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Speed(Britsh
2.5 3.0 3.0 3.5 3.0 3.5 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5
Incline
0.5 1.0 1.5 2.0 2.0 2.5 2.5 3.0 3.0 3.5 3.5 4.0 4.0 4.5 4.5 4.5 4.0 4.0 3.5 3.5 3.0 3.0 2.5
Speed(Metric)
4.0 4.8 4.8 5.6 4.8 5.6 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2
Warm up
22 23 24 25 26
3.5 3.0 3.5 3.0 3.5 3.0 2.5
2.5 2.0 2.0 1.5 1.5 1.0 0.5
5.6 4.8 5.6 4.8 5.6 4.8 4.0
Cool Down
(WARM_UP last 2:00 minutes and COOL_DOWN last 2:00 minutes, both of them are included in program times)
HILLWALK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Speed(Britsh
2.5 3.0 3.0 3.5 3.0 3.5 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5 5.0 4.5
Incline 0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0 1.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0 0.0 0.0 0.0 1.0 1.0 1.0
Speed(Metric)
4.0 4.8 4.8 5.6 4.8 5.6 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2 8.0 7.2
Warm up
22 23 24 25 26
3.5 3.0 3.5 3.0 3.5 3.0 2.5
1.0 1.0 0.0 0.0 0.0 0.0 0.0
5.6 4.8 5.6 4.8 5.6 4.8 4.0
Cool Down
(WARM_UP last 2:00 minutes and COOL_DOWN last 2:00 minutes, both of them are included in program times)
CARDIO CHALLENGE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Speed(Britsh
2.0 2.0 2.0 3.0 4.0 3.0 4.0 4.0 3.0 3.0 4.0 4.0 5.0 5.0 4.0 4.0 5.0 5.0 4.0 4.0 3.0 3.0 4.0
Speed(Metric)
3.2 3.2 3.2 4.8 6.4 4.8 6.4 6.4 4.8 4.8 6.4 6.4 8.0 8.0 6.4 6.4 8.0 8.0 6.4 6.4 4.8 4.8 6.4
Warm up 22 23 24 25 26
4.0 3.0 3.0 3.0 2.0 2.0 2.0
6.4 4.8 4.8 4.8 3.2 3.2 3.2
Cool Down
(WARM_UP last 2:00 minutes and COOL_DOWN last 2:00 minutes, both of them are included in program times)
ENDURANCE CHALLENGE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Incline
0.5 0.5 1.0 1.5 1.0 1.5 2.0 2.0 2.5 2.5 2.0 2.5 2.5 2.5 2.0 2.0 2.5 2.0 2.0 1.5 1.5 2.0 2.0
Warm up 22 23 24 25 26
1.5 1.0 1.0 0.5 0.5 0.0 0.0
Cool Down
(WARM_UP last 2:00 minutes and COOL_DOWN last 2:00 minutes, both of them are included in program times)
CROSS COUNTRY
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Speed(Britsh 2.5 3.0 3.0 4.5 3.0 4.0 3.0 5.0 3.0 5.0 3.0 5.0 3.5 5.0 3.5 5.0 3.5 5.0 3.5 5.0 3.0 5.0 3.0
Speed(Metric)
4.0 4.8 4.8 7.2 4.8 6.4 4.8 8.0 4.8 8.0 4.8 8.0 5.6 8.0 5.6 8.0 5.6 8.0 5.6 8.0 4.8 8.0 4.8
Warm up
22 23 24 25 26
5.0 3.0 4.5 3.0 4.5 3.0 4.0
8.0 4.8 7.2 4.8 7.2 4.8 6.4
Cool Down
(WARM_UP last 2:00 minutes and COOL_DOWN last 2:00 minutes, both of them are included in program times)
832T GETTING STARTED
1) Check to make sure no objects are placed on the
belt that will hinder the movement of the treadmill.
2) Plug in the power cord and turn the treadmill ON.
3) Stand on the side rails of the treadmill.
4) Attach the safety key clip to part of your clothing.
5) Insert the safety key into the safety keyhole in the
console.
6) You have two options to start your workout:
A) QUICK START UP
Simply press the START key to begin working out.
OR...
B) SELECT A TARGET AND WoRKoUT
Select a PROGRAM using one of the QUICK
PROGRAM keys or using the ARROW keys
(MANUAL, INTERVALS, MOUNTAIN WALK, WEIGHT
LOSS WALK, HILL WALK, CARDIO, CHALLENGE,
ENDURANCE CHALLENGE.CROSS COUNTRY,
ROCK CLIMB, FAT BURN, 100 KCAL BURNING,
300 KCAL BURNING, 500 KCAL BURNING).
C) SELECT A TIME oR DISTANCE
Select a Time or DISTANCE using the ARROW keys
or use the Quick TIME OR DISTANCE keys. Once a
TIME or DISTANCE has been chosen, press ENTER.
SELECTING A PRoGRAM
• QUICK KEY oPERATIoN: Once you have started your
program you can quickly change your speed and incline level.
• To RESET CoNSoLE: Hold STOP key for 3 seconds.
• FINISHING YoUR WoRKoUT: When your workout is
complete your workout information will stay displayed on the
console for 30 seconds and then reset.
• CLEAR CURRENT SELECTIoN: To clear the current
program selection or screen, hold the STOP button for 3
seconds.
• SCAN VIEWING SCREENS: To have the display screen
rotate continuously (Time, Incline, Pulse and Distance, Speed,
Calories):
- Hold Change Display / Enter Button for 4-5 seconds
- Console will beep twice when activated.
- To deactivate, press enter one time without holding.
832T832T