Hover-1 Buggy User manual

Operation Manual HY-H1-BGY
*Images used in this manual may vary slightly from
the product and are for reference purposes only.
IMPORTANT: KEEP FOR FUTURE REFERENCE
Even if you have ridden a scooter for years, it is important for you
and every rider to read this manual before using this product.
1

HELMETS SAVE LIVES!
Always wear a properly tted helmet that complies with CPSC or CE safety standards
when you ride your scooter.
WARNING
Correct Fitting:
Make sure your helmet
covers your forehead.
Incorrect Fitting:
Forehead is exposed
and vulnerable to
serious injury.
2

This manual is designed to give you the information you need for the safe operation and maintenance of your
new Hover-1 Buggy. Please read it thoroughly before riding your Hover-1 Buggy.
Section One of this manual involves safety and Hover-1 Buggy care. Understanding and following this
Information will help you and your Hover-1 Buggy avoid injury or damage.
Section Two of this manual gives assembly and installation instructions for your Hover-1 Buggy.
Section Three of this manual covers specic safety and operating instructions for your Hover-1 Buggy. Even if
you are an experienced rider, you should review this section before your rst ride.
Section Four of this manual covers warranty specications of your Hover-1 Buggy.
INTRODUCTION
WARNING
Make sure you read this complete manual before riding
your Hover-1 Buggy. Failure to do so, or failure to follow its
guidelines could lead to serious injury or death.
3

HOVER-1 BUGGY DIAGRAM
SPECIFICATIONS
1. Seat
2. Handle Bars
3. Pedal Mounts
4. Adjustable Strap
5. Seat Frame
6. Locker
7. Frame
8. Foot Rests
9. Front Wheel
Compatibility: Most self-balancing scooters
Max Load: See max load of your self-balancing scooter
Tire Size: 4” swivel caster
Seat Material: PP
4
1
2
3
4
5
6
78
9
2
3
4
6
8

PARTS LIST
(1) Seat
(1) Seat Frame
(1) Frame
(1) Left Handle Bar
(1) Right Handle Bar
(2) Strap with velcro
(1) Wrench
(4) Small Foam pad
(1) Allen Wrench
(2) Locker
(2) 8*35 Screw
(4) M6*16 Screw
(4) Spare strap
with velcro (2) 8mm Nut
5

ASSEMBLING YOUR HOVER-1 BUGGY
If you have questions or concerns about any of these steps, please feel free to contact our Customer Service
Team at [e-mail]. Someone will be in touch to walk you through these steps.
Carefully follow the steps shown on the following pages for assembling the Hover-1 Buggy.
Remove all Hover-1 Buggy contents from the box. Ensure all contents from the “Parts List” section are
accounted for.
1. Locate the 4 foam pads and both handle bars. Remove the adhesive backing from each foam pad and
center to each side of the papal mounts as shown below. Ensure all of the foam pads are prosperity adhered
to pedal mounts.
6

2. Locate the provided 8*35 Screw and 8mm Nut. Attach the left and right handle bars to the seat frame as shown
below.
3. Insert the frame into the seat frame. Adjust the frame and the seat frame to your preferred size. Secure the frame
in place using the locker.
7
Seat Frame

4. Align the holes of the seat with the seat frame. Secure the seat in place by M6*16 screws using allen wrench.
5. Your Hover-1 Bubby is now completely assembled and should look like the below image.
8

INSTALLING YOUR HOVER-1 BUGGY
If you have questions or concerns about any of these steps, please feel free to contact our Customer Service
Team at [e-mail]. Someone will be in touch to walk you through these steps.
Carefully follow the steps shown on the following pages for installing the Hover-1 Buggy onto your electric
scooter. Read the remainder of this manual before riding your Hover-1 Buggy.
Your Hover-1 Buggy should be completely assembled prior to installing it onto your electric scooter. Please
refer to the “Assembling your Hover-1 Buggy” section for assembling procedures.
1. Place the pedal mounts onto the foot pedals of your self-balancing scooter with the front wheel facing
forward. Ensure the pedal mounts are centered on the foot pedals of your scooter as much as possible.
9