Hover-1 Go-Kart User manual

ELECTRIC SCOOTER ACCESSORY
GO-KART

Operation Manual HY-ALL-CMB Go-Kart
*Images used in this manual may vary slightly from
the product and are for reference purposes only.
IMPORTANT: KEEP FOR FUTURE REFERENCE
Even if you have ridden a scooter for years, it is important for you
and every rider to read this manual before using this product.
ELECTRIC SCOOTER ACCESSORY
GO-KART
1

HELMETS SAVE LIVES!
Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you
ride your scooter.
WARNING
Correct Fitting:
Make sure your helmet
covers your forehead.
Incorrect Fitting:
Forehead is exposed and
vulnerable to serious injury.
2

This manual is designed to give you the information you need for the safe operation and maintenance of
your new Hover-1 Go-Kart. Please read it thoroughly before riding your Hover-1 Go-Kart.
• Section One of this manual involves safety and Hover-1 Go-Kart care. Understanding and following this
Information will help you and your Hover-1 Go-Kart avoid injury or damage.
• Section Two of this manual gives assembly and installation instructions for your Hover-1 Go-Kart.
• Section Three of this manual covers specific safety and operating instructions for your Hover-1 Go-Kart. Even
if you are an experienced rider, you should review this section before your first ride.
• Section Four of this manual covers warranty specifications of your Hover-1 Kart.
INTRODUCTION
WARNING
Make sure you read this complete manual before riding
your Hover-1 Go-Kart. Failure to do so, or failure to follow
its guidelines could lead to serious injury or death.
3

HOVER-1 GO-KART DIAGRAM
SPECIFICATIONS
1. Adjustable Seat
2. Handle Bars
3. Pedal Mounts
4. Elastic Strap
5. Seat Frame
6. Twist Knob
7. Frame Extension
8. Foot Rests
9. Caster Wheel
10. Flag
Compatibility: Most 6.5” scooters
Max Load: See max load of your scooter
Tire Size: 4” swivel caster
Seat Material: PP
4

PARTS LIST
(1) Seat Base
(1) Seat Frame
(1) Frame extension
(1) Seat Back Frame
(1) Left Handle Bar
(1) Right Handle Bar
(2) Elastic strap
(4) Spare Elastic straps
(2) Twist Knob
Allen Wrench Set:
(2) 5mm wheel change
(1)
6mm seat frame assembly
(2) Large Screws
(6) Small Screws
(2) Large Washers
(1) Flag Set
(1) Seat Back
5

ASSEMBLING YOUR HOVER-1 GO-KART
If you have questions or concerns about any of these steps, please feel free to contact our Customer Service
Team at www.hover-1.com. Someone will be in touch to walk you through these steps.
Carefully follow the steps shown on the following pages for assembling the Hover-1 Go-Kart.
Remove all Hover-1 Go-Kart contents from the box. Ensure all contents from the “Parts List” section are
accounted for.
1. Using the two large screws and two large washers. Attach the handle bars to the appropriate sides of the
seat frame as shown below. Tighten with included 6mm Allen wrench.
6

2. Align the holes of the seat with the seat frame. Secure the seat in place using the included Allen wrench,
four small screws.
7

3. Insert the frame extension into the seat frame. Adjust to preferred length. Secure the frame extension in place
using one twist knob.
8

4. Align the holes of the seat back with the seat
back frame. Secure the seat back in place using the
included Allen wrench and two small screws.
6. Your Hover-1 Go-Kart is now completely assembled
and should look like the below image.
5. Insert the seat back frame into the seat frame.
Adjust to preferred length. Secure the seat back frame
in place using one twist knob.
9