HPRT HM-A300E User manual

12
345
Packing List
Printer USB Cable
Paper Roll Perspe-
ctive Window
Cover-opening Bu-
tton
Paper Feed
Battery
[MODE]
Button
Paper Guide
LCD
Note:The items in the package are actually based
on the order.
！
Appearance and Components
Front View
Rear View
Inside View Platen
Tear Bar
USB Interface
Thermal Print Head
Loading Paper
1. Press the cover-opening button to open the paper
cover.
3.Load the paper in the orientation shown in the figure below.
Make sure that the thermosensitive layer is facing down. Adjust
the paper guide per the paper width. After
adjusting, lock the paper guide.
2.Unlock the paper guide as shown below.
4. Pull some extra paper and close the cover.
Make sure that it is closed on both sides.
5. Use the tear bar to tear the extra paper.
Quick Start Guide
Battery Pack
AC Adapter
Thermo sensitive Layer
Unlock
Lock
Quick Start Guide
HM-A300E
Manufacturer: Xiamen Hanin Electronic Technology Co.,Ltd.
Address: No.96, Rongyuan Road, Tong'an District, Xiamen, China
E-mail: [email protected]
Web: www.hprt.com
Roll Paper

6
9
7 8
Battery Pack Installation
1. Make sure that the printer has been turned off before you insert or
remove the battery pack.
2. Insert the battery pack into the back of the printer as in the figure
shown below, following the direction of the arrow. Press down on the
battery pack until the hook click into place.
3. To remove the battery back, pull back the hook, and use the opposite
procedure from the one you used to insert the battery pack.
Hook
Battery Charging
Please charge the printer with the supplied USB cable.
When battery pack runs out of power, the battery icon on the
LCD will flash. It powers off automatically when continues print-
ing. If you want to go on, please charge it.
Menu Settings
1. Press and hold the [MODE] button for approx.
2 seconds, and printer is turned on.
2. Press and hold both [MODE] button and [FEED]
button, the main menu is displayed on the screen,
followed by:
Density：dark/ light/ medium
Paper：label/receipt/Front black mark 2 inches/
Front black mark 3 inches/Rear black mark 3 inches
Cover closing and paper feeding：off/on
Express：standard and so on
Standby time
Shutdown time
Rotate
Self-test page printing
Label positioning
Exit menu
HM-A300E-XXXX
◆Before changing the menu setting, make sure that the
communication with a host device is disconnected.
◆When the printer is under the Bluetooth communication
with a host device, it cannot enter the Menu Settings mode.
Note:
Receipt
[MODE] button [FEED] button
Note：
1. If the user replaces the wrong type of battery by himself, there will be
explosion danger. Please be sure to send it back to the maintenance site
according to the instructions to dispose of the used battery.
2. This is a Class A product. In a domestic environment this product may
cause radio interference in which the user may be required to take ade-
quate measures.
Charge via AC Adapter
Charge via PC
3. Press [MODE] button to change the option.
4. Press [FEED] button to change the category of suboption;
press and hold [FEED] button to confirm the current setting.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator & your body.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
9