Huawei TE30 User manual

1
HUAWEI TE30 Videoconferencing Endpoint
Quick Installation Guide

What's in the Box
HUAWEI TE30
videoconferencing endpoint
Power adapter
Power cable
L-shaped bracket, 1/4"-UNC
screw, and hook-and-loop
fastener
Accessorial integration cable
HDMI cable
Network cable
Remote control
Qualification Card
Warranty Card
Safety Precautions
Quick Start Guide
The power adapter, power cable, and accessorial integration cable in the box can be used only with the
endpoint in the same box. The item pictures are for your reference only.

2

Installation
Standard Mounting
Use the L-shaped bracket and hook-and-loop fastener to secure the TE30 on top of the
monitor. Select an installation option based on the monitor width.
If the thickness of the monitor is 97 mm (3.82 in.) or slimmer, follow the steps in the
following figure.

3
If the thickness of the monitor is between 97 mm (3.82 in.) and 170 mm (6.69 in.), follow
the steps in the following figure.
If the monitor is 170 mm (6.69 in.) or thicker or is wall-mounted, use the free-standing, wall-
mounting, inverted installation, or other installation options.
Free-Standing
Place the TE30 on a flat surface.
If you have to place the TE30 on an inclined surface, ensure that the inclination is less than
15°so that the TE30 can function properly.

4
Wall-Mounted
Use the L-shaped bracket to wall-mount the TE30.
Before mounting the TE30 onto the wall, connect all required cables to the TE30.
Inverted Installation
Purchase a bracket for inverted installation and mount the TE30 onto the ceiling.
Use the 1/4"-UNC screw to secure the TE30 to the bracket.
Other Installation Options
Purchase a tripod and install the TE30.

5

Connecting Cables
The VGA cable is not provided with the TE30. You need to purchase it by yourself.
The cable connection shown in the preceding figure is the simplest and provided only for reference. Visit
http://enterprise.huawei.com to access the HUAWEI TE30 Videoconferencing Endpoint User Guide for more
cable connection instructions.

Power On the TE30
With all cables connected correctly, to get the power adapter connected with TE30, with the
power supply on, then, the TE30 will be automatically powered on. The following table describes
the TE30 indicator status.

6
Indicator
Status
TE30 Status
Indicator
Status
TE30 Status
Blinking
green
Starting
Steady orange
Powered off but connected to the power
supply
Steady
green
Operating
properly
Off
Disconnected from the power supply
Blinking
orange
Sleeping
Blinking red
Encountered a fault, such as a self-
check error, overheating, and software
malfunction

Loading the Configuration File
Using a USB Flash Drive
The TE30 automatically loads the configuration file from the USB flash drive. After the
configuration file is loaded, the TE30 can work properly.
The USB flash drive and configuration file thereon are provided by the reseller or operator. Do
not modify the configuration file. To obtain a USB flash drive, contact the local reseller or
operator.
To load the configuration file on the USB flash drive:
1. Insert the USB flash drive into the USB port in the TE30.
2. When Popup prompts, click Yes.
The TE30 automatically loads the configuration file and restarts.
If you do not perform any operations within 10 seconds after you insert a USB flash drive, the TE30
automatically loads the configuration file and restarts.
3. Remove the USB flash drive.
Using Other Methods
You can also use the methods described in the "Configuring the TE30" section in the HUAWEI
TE30 Videoconferencing Endpoint Quick Start Guide.
Do not turn the TE30 or stop it from turning using your hands or other
forces when the TE30 is powered on and working properly.