human care Roomer S 55300-EU User manual

Page 1
www.humancaregroup.com
Using the lift
10
4
2
3
5
oImportant! If the buttons on the
hand control or control panel
are used to feed the belt back
into the lift, the belt must be kept taut
until the entire belt has been fed in.
oImportant! Do not turn the
lever unless both belts are
connected to their respective rail
rollers. The lever (10) must always
point towards the belt that the lift is
suspended from or is to be transferred
over to! When the lift is suspended
from only one of the lift belts and the
lever (10) is turned over to the free
belt, the loaded belt will be released if
you physically raise the lift. This can
result in the lift falling, which may be
dangerous. Turn the lever (10) back
immediately to the loaded belt to
avoid unintentional disconnection!
Press the Up button on the hand
control or control panel on the lift to
lift the patient. Press the Down but-
ton on the hand control or control
panel to lower the patient. Pressing
the button activates a soft start,
and releasing it causes a soft stop.
The direction of the lever (10)
determines which belt is engaged
and which is active. If the lever
(10) is pointing towards the leg
hook (5) the belt nearest the leg
hook (3) is active. If the lever
(10) is pointing towards the teles-
copic bar (4) the belt nearest the
telescopic bar (2) is active.
Set the telescopic bar (4) to the
prescribed position. Ensure that
the bar hooks are in the same
position on both sides. Place the
patient in the prescribed sling
according to the sling instructions
and hang the sling in the hooks on
the telescopic bar and in the leg
hook (5). Check that the sling’s
lifting straps are properly anchored
in all hooks.
Description
The General A portable overhead lift with room-to-room functionality provides you with a unique ability to move a patient safely and easily from one room
to another or from one rail system to another. The lift has two belts, both of which are connected to the rail during a transfer, allowing the transfer to take
place horizontally. The transfer takes place in one operation, which means that both the patient and caregiver avoid exposure to unnecessary strain
during lifting and moving. The lift is used for lifting and moving a patient, for example to or from a bed, wheelchair or toilet or from the floor. The apparatus
can also be used for walking training, and with the help of some accessories, for balance training and weighing.
Quick Reference Guide
– Roomer S
Part no:
North America: 55300-NA
Europe: 55300-EU
Australia: 55300-AU
Great Britain: 55300-GB
Japan: 55300-JP
Hand control
Lift belt
(bar side)
Lift belt (leg hook side)
Telescopic
bar
Leg hook
Secondary control
panel
Emergency lowering button
Indicator
Emergency stop
Lever (room-to-room
transfer)
Helpful Troubleshooting Tips!
The lift will not work while plugged in and/or if emergency stop is engaged

Page 2
IMPORTANT! This quick reference
guide does not replace the user
manual which can be downloaded
at www.humancaregroup.com
AUSTRALIA
Unit 9, 271 Wells Road
Chelsea Heights, Victoria 3196
Phone:- [phone]
Fax:- [phone]
Email: [e-mail]
CANADA
10-155 Colonnade Road
Ottawa, ON K2E 7K1
Phone:- 613.723.6734
Fax:- 613.723.1058
Email: [e-mail]
SWEDEN
Årstaängsvägen 21C
117 43 Stockholm
Phone:- [phone]
Fax:- [phone]
Email: [e-mail]
UNITED STATES
4210 S. Industrial Drive, Suite 160
Austin, TX 78744
Phone:- 512.476.7199
Fax:- 512.476.7190
Email: [e-mail]
Quick Reference Guide
– Roomer S
Room to room transfer
Move the patient to the doorway or
to the place where the room-to-room
transfer is to take place. Raise the lift
until it is approx. 10 cm away from the
hook. Pull out the non-active lift belt
and hook it securely diagonally from
above in the hook in the other room or
the other rail system.
Turn the lever over so that it points
towards the direction in which you
want to move the patient. Check
that the lever has been turned over
properly. Now both lift belts are con-
nected.
Press the Up button on the hand con-
trol or on the control panel and keep it
pressed in to perform the transfer to
the other room. Transfer is complete
when the lift belt in the room you left
has been released.
Unhook the belt that has now been
released. Hold onto the belt, which is
automatically retracted to the lift.
Continue further along the rail in the
next room or next system.
99588-Quick reference guide-Roomer S-Rev01 (2015-07-23)
The lift offers a unique ability to move a patient smoothly and easily from one room to another or from one rail system to another. The transfer
takes place horizontally in a manner that is safe and comfortable for the patient. It requires no structural engineering measures such as making
holes in or above doors.
Important! To ensure that the lift belt will not be damaged, it is important that the lift is balanced during moving,
lifting and lowering operations. Never hold or pull the lift belt when moving a patient.
The telescopic hanger bar
o
Important! Do not hold on
to the telescopic bar or the
hooks when performing a lift.
The hooks on the telescopic bar have three adjustable positions (40, 50 and 60 cm). To change position, turn the hooks
1/4 turn while pushing or pulling the hooks to the desired position. The hooks will automatically fall into place in the posi-
tion, and so it is necessary to repeat the turn (1/4 turn) when passing the middle position (position 2) (See fig).