human care Staffan RA Instructions for use

1
Staffan RA
To secure that the walking-aid will function safely for the user, once per
year review of the walking-aid should be done.Therefore is the following
interventions recommended.
Wing nut
Control function.
CE-marking
Make sure that the CE-marking
is still there and readable.
Wheels
Make sure the wheels are not
worn-out and are spinning easily
without any noice.
Front forks
Make sure that the forks swings
easily.
Lubrication
The front forks shall function
without noice, lubricate when
needed.
Stability
Control that all wheels are steadily on the ground and that there are no chassis
distortion.
Test driving
Make a nal control by test driving.
Cleaning
When cleaning the walker it is recommended machine washing, 60 degrees for
10 minutes.When using a pressure washer, do not wash directly to the bearings.
In addition to machine washing, regular cleaning with a mild cleanser is
recommended. Note! Do NOT use thinner, petrol or other solvents.
Post treatment
After washing, all connections, tight spaces and drainage holes should be blown
dry and sprayed with thin oil. If degreaser is used, should the moving parts be
lubricated.
The Paint
Control damages to the paint.To prevent corrosion, improve scratches.Touch-up
paint can be ordered from Human Care HC AB.
Pipe frame
Control weldings and screw attaches. If the corrosion is extensive shall the
rollator be replaced.
Handle
Must be xed. Make sure the handle pipes can be pushed
down to the chassis. Change the grip if needed.
Brakes
Control that both brakes and parkingbrakes are working.
Wires should be intact and stapped to the chassis.
RECONDITIONING MANUAL

2
Spareparts list
Product number:
Owner:
Notes:
Attended by:
Place and date:
Note!
Recondition must be done by a person how has good knowledge about how the
job should be performed.An incorrect performed recondition could result an
accident/incident. Don´t hesitate to contact your retailer if questions come up.
When exchanging parts of the rollator, use only Human Care parts to ensure
continued CE-validation.
When disassembling of a wheel, the wheel nut and pin bolt must be replaced
since they contain a self-locking that will be destroyed when disassembling.
If the corrosion is more than a lm of rust the rollator shall be discarded and
return for recycling.
Intended use
The rollator should only be used as support whilst walking. Do not alter the
rollator yourself.
RECONDITIONING MANUAL
No Designation Quantity Art. no Other information
1 Rear fork right complete 1 400-019H Pin bolt and wheel nut must be
exchanged when disassemble the fork.
2 Rear fork left complete 1 400-019V Pin bolt and wheel nut must be
exchanged when disassemble the fork.
3 Front fork 2 200-006 Pin bolt and wheel nut must be
exchanged when disassemble the fork.
4 Cover lid 2 20-014
5
6
7
Wheel kit
Wheel with bearing
Pin bolt
Wheel nut
4
4
4
4
89015 Pin bolt and wheel nut must be
exchanged when disassemble the wheel.
8 Brake 2 10-013
9 Pop nut-brake 2 000139
10 Starlock-D6 6 00113
11 Brake spring 2 00131
12 Adjustment screw 2 10-010
13 Wire lock 2 10-017
14
15
16
Wing nut complete
Wing nut
Screw
Washer
4
4
4
4
50937 Lubricate the wing nut when needed.
17 RA handle 2 20-064
18 Handle brake complete 2 10650 Complete with housing, brake handle
and pop nut.
19 Handle 2 00020
20 RA-cushion 1 20-054
21
21
RA bracket left
RA bracket right
1
1
400-001H
400-028H
Staffan RA low
Staffan RA high. Complete with handle
pipe.
22
22
RA bracket left
RA bracket right
1
1
400-001V
400-028V
Staffan RA low
Staffan RA high. Complete with handle
pipe.
23 Handle pipe 1 400-025 Staffan RA low
Wire and housing
Wire and housing
2
2
89100
89105
Staffan RA low
Staffan RA high

3
1
2
3
4
5
6,7
8
9
10
11,12,13
14
15,16
19
18
17
20,21
20,22
23
99218-Rev F (2013-11-20)
RECONDITIONING MANUAL
• Årstaängsvägen 21C, SE-117 43 Stockholm, Sweden •
• Tel. +46(0)8 - 510 132 00 • Fax +46(0)8 - 665 35 10 •
• www.humancaregroup.com •