human care Rebel Instructions for use

1
Rebel
To secure that the walking-aid will function safely for the user, once per
year review of the walking-aid should be done.Therefore is the following
interventions recommended.
Wing nut
Control function.
Reectors
Make sure the reectors are still there
and visible.
CE-marking
Make sure that the CE-marking
is still there and readable.
Wheels
Make sure the wheels are not worn-out
and are spinning easily without any noice.
Lubrication
Gatebushings and hinges should be working without any noice. Lubricate when
needed.
Front forks
Make sure that the ball bearings is rmly attached. Check the front fork inertia
by allowing the wheel to swing between 3 and 9 o’clock. Both wheels shall swing
3 to 10 times with max 2 swings difference between each wheel.The inertia can
be adjusted by adjusting the screw M12x56/M12x45. Note! When adjusting the
inertia, the screw M12x56/M12x45 and screw M6x7 must be exchanged.
Folding mechanism
Should be intact and the locking should function.
Seat
Make sure the seat is kept in place and
screws are tightened.
Stability
Control that all wheels are steadily on the ground and that there are no chassis
distortion.
Test driving
Make a nal control by test driving.
Cleaning
When cleaning the walker it is recommended machine washing, 60 degrees for
10 minutes.When using a pressure washer, do not wash directly to the bearings.
In addition to machine washing, regular cleaning with a mild cleanser is
recommended. Note! Do NOT use thinner, petrol or other solvents.
Post treatment
After washing, all connections, tight spaces and drainage holes should be blown
dry and sprayed with thin oil. If degreaser is used, should the moving parts be
lubricated.
The Paint
Control damages to the paint.To prevent corrosion, improve scratches.Touch-up
paint can be ordered from Human Care HC AB.
Pipe frame
Control weldings and screw attaches. If the corrosion is extensive shall the
rollator be replaced.
Handle
Must be fixed. Make sure the handle pipes can be pushed
down to the chassis. Change the grip if needed. Note!
Only use alcohol without moisturizing agents.
Brakes
Control that both brakes and parkingbrakes are
working. Wires should be intact and stapped to the
chassis.
RECONDITIONING MANUAL

2
Spareparts list
Product number:
Owner:
Notes:
Attended by:
Place and date:
Note!
Recondition must be done by a person how has good knowledge about how the
job should be performed.An incorrect performed recondition could result an
accident/incident. Don´t hesitate to contact your retailer if questions come up.
To secure safe usage of the product, only original parts should be used, these
have been developed and tested against current product standards. It is only with
original parts that the warranty and CE labeling is valid.
When disassembling of a wheel, the wheel nut and pin bolt must be replaced
since they contain a self-locking that will be destroyed when disassembling.
If the corrosion is more than a lm of rust the rollator shall be discarded and
return for recycling.
Intended use
The rollator should only be used as support whilst walking or as seating whilst
stationary. Do not alter the rollator yourself.
Specic instructions for Rebel low and reinforced.
Unique spareparts for low and reinforced Rebel models are listed in the bottom
of the sparepart list.These spareparts are strictly intended for use togheter with
the above mentioned products. Please note that other spare parts in the list
might not be suitable for these products.
RECONDITIONING MANUAL
No Designation Quantity Art. no Other information
Wheel kit 89015 For Rebel reinforced use 89086 for rear
1
2
3
Complete wheel
Wheel nut
Pin bolt
1
1
1
wheel.
Pin bolt and wheel nut must be ex-
changed when disassemble the wheel.
Pin bolt & Wheel nut 89032 For Rebel reinforced use 89091 for rear
2
3
Wheel nut
Pin bolt
1
1
wheel
Pin bolt and wheel nut must be ex-
changed when disassemble.
Front fork kit 89025 From 200907 (Rebel low from 201304)
2
3
Front fork
Bearing
Wheel nut
Pin bolt
Cover cap
Screw M12x56
Screw M6x7
Washer
Locking washer
1
2
1
1
1
1
1
1
1
Not for Rebel reinforced.
Pin bolt and wheel nut must be
exchanged when disassemble the fork.
Front fork kit 89045 Notice! For the old and reinforced model
2
3
Front fork
Wheel nut
Pin bolt
Screw cover
Screw M12x45
1
1
1
1
1
of Rebel. Not for Rebel low.
Pin bolt and wheel nut must be
exchanged when disassemble the fork.
Add 89091.
Brake kit 89095 Pin bolt and wheel nut must be
4
5
6
7
8
9
10
11
12
Brake inner part
Brake outer part
Pop nut
Wear washer
Screw M6x6
Washer
Adjustment screw
Spring
Screw M6x16
1
1
1
1
1
1
1
1
1
exchanged when disassemble the brake.
Note! Specic nut and pin bolt for
reinforced Rebel.Add 89091.
2 Wheel nut 1
3 Pin bolt 1
7 Wear washer 1 10-004 Wear washer turns when worn.
Handle kit 89055 For left and right.
13
14
15
Handle pipe
Handle brake complete
Handle ERGO
1
1
1
15 Handle ERGO 1 20-024

3
4
10
12 9
8
6
5
7
11
13
14
15
16
18
17
24
21
22
23
20
1
3
2
19
99212-Rev 02, (2018-02-13)
RECONDITIONING MANUAL
• Årstaängsvägen 21B, SE-117 43 Stockholm, Sweden •
• Tel. +46(0)8 - 510 132 00 • Fax +46(0)8 - 665 35 10 •
• www.humancaregroup.com•
Wing nut complete 50937 Lubricate the wing nut when needed.
16
17
18
Wing nut
Screw
Washer
1
1
1
19 Wire complete 89050
Wire housing
Wire
Wire lock
Wire end
1
1
1
1
Seat kit 89020
20
21
22
23
24
Seat
Gate lock
Fold loop
Screw M6x20
Screw to gate lock
1
1
1
1
Seat complete 89070
20
23
Seat
Screw M6x20
1
2
Tube protection 1 50949
22 Fold loop 1 10-009
Gate lock kit 10-018
21
24
22
Gate lock
Screw to gate lock
Fold loop
1
4
1
Reex 1 00028
Touch-up paint 1 F2
Front fork
Cover
Locking washer
Distance washer
Spring
Washer
Front fork
Bushing
1
1
1
1
1
1
2
20-014
00111
00136
00130
20-030
200-006
20-026
Until 201303
Pin bolt and wheel nut must be exchanged
when disassembling the fork.
Cover 1 70886 From 201304
Spareparts Rebel low (Art. no: 21111, 21211, 21311, 21411)
Wheel kit back 89086 Pin bolt and wheel nut must be exchanged
1
2
Complete wheel
Wheel nut
Pin bolt
1
2
1
when disassemble the wheel.
Handle 1 89033 When changing the handle, the upper part
of the reinforcement beam must be removed.
2
Pin bolt & wheel nut for
rear wheel
Wheel nut
Pin bolt
2
1
89091 Pin bolt and wheel nut must be exchanged
when disassemble.
Spareparts Rebel reinforced (Art. no: 71221, 71321, 71421)