Hunter Products Rollplay W458 Assembly instructions

Owner’s Manual and Assembly Instructions
Model #: W458, 43541 47302
Read and understand the entire manual before assembly and operation. The vehicle must be
assembled by an adult who has read and understands the instructions.
Made in China.
IMPORTANT:
Save this manual with your sales receipt.
6V Audi R8 Spyder

Introduction
Thank you for purchasing this RollPlay vehicle. We hope
the rider enjoys it for miles to come. Please read this instruction guide
carefully before assembling and operating the vehicle. Please contact
Hunter Products Pty Ltd at www.electricrideon.com.au or Call
at 1800 224 094 with any enquiries or questions.
Specifications:
BATTERY 6V 7AH
MOTOR 6V 15W
AGE 3 Years and Up
MAX WEIGHT 35 KG (77 lbs)
PRODUCT SIZE 1.2 m x 62 x 50 cm (47.2 x 24.4 x 19.7 in.)
SPEED 4.0 km/h (2.5 MPH)
RECHARGE TIME 8-12 Hours
TYPICAL RUN TIME 1-2 Hours
CHARGER OUTPUT DC 7.0V
WARNING!
• Non-rechargeable batteries are not to be recharged;
• Batteries are to be inserted with the correct polarity;
• Exhausted batteries are to be removed from the toy;
• The supply terminals are not to be short-circuited.
• Rechargeable batteries are only to be charged under adult
supervision;
• Rechargeable batteries are to be removed from the toy before being
charged;

3
Table of Contents
Safety..........................................................4
Parts ..........................................................6
Charging Instructions ...............................7
Assemble the Front Wheels.................... 8
Assemble the Rear Wheels..................... 9
Dashboard/Windshield Assembly ..........10
Assemble the Steering Wheel ................11
Attach the Mirrors ...................................12
Attach the Seat ........................................13
Operation Instructions ............................14
Battery Removal ......................................15
Attach the R/C batteries ........................16
Remote Control Operation .....................17
Maintenance ............................................19
General Care ............................................20
Troubleshooting Guide............................21
Service and Repairs ................................23
Warranty ...................................................24

complies with Australian Standard AS/NZS 2063:2008.
4Safety
WARNING: SAFETY RIDING RULES
The user must follow all safety rules and guidelines, or serious injury or death may
occur to the user.
• Always use common sense and safe practices when using the vehicle. The user
must be at least 3 years old and weigh no more than 35kg (77 lbs).
• This product contains small parts that are for adult assembly only. Keep small
children away when assembling. Remove and dispose of all protective material
and plastic bags before assembly.
•
• Only sit on the seat in the vehicle.
• Do not allow more than one rider.
• Do not overload the vehicle. Do not remove the weight restriction decals.
• Do not pull the vehicle with another vehicle or similar device.
• Keep body parts such as hands, legs, hair and clothing away from moving parts.
Moving parts can cause serious injury.
• Always wear shoes in the vehicle.
• Do not operate near streets or motor vehicles.
• Do not operate near drop-offs such as steps, steep inclines or hills. Operate on
relatively level ground.
•
• Do not operate in dangerous weather conditions such as rain or snow.
•
•
•
•
•
•
•
•
Always use the vehicle in a safe, secure environment with adult supervision.
PREVENT INJURIES AND DEATHS:
NEVER LEAVE CHILD UNATTENDED. ALWAYS
keep child in view when child
is in vehicle. Direct adult supervision is REQUIRED.
NEVER use in roadways, near cars, on or near steep inclines or steps, swimming
pools or other bodies of water.
ALWAYS wear shoes.
ALWAYS sit on the seat.
RISK OF FIRE. Do not bypass.

5

6Parts
1. Car Body
2. Seat
3. Steering Wheel
4. Dashboard
5. Windshield
6. Left and Right Mirrors
7. Front Wheel (2)
8. Rear Wheel (2)
9. Hubcap (4)
10. Battery Charger
11. Steering Wheel Screw
12. Steering Wheel Nut
13. Dashboard Screw (2)
14. Snap Pin (4)
15. Large Washer (7)
16.
17. Remote Controller
Inner Wheel Spacer
•Phillips screwdriver
•Pliers
Not Included:
1
2
3
4
17
5
7
8
9
10
Helpful Tip:
1. Parts 11-16 are located
2. Spare parts:
Large washer 2
Snap pin 2
in the blister pack
13
11
14
15
16
12
6

7

8Assemble the Front Wheels
1.
2. Slide the front wheel (7) onto the axle. Ensure that the side of the wheel with the
slots is facing out
3. Slide the large washer (15) onto the axle
4. Insert the straight side of the snap pin (14) through the hole at the end of the axle
to keep the wheel in place
5. Position the hubcap (9) over the holes on the wheel, and snap the hubcap into
place
6. Repeat sets 1-5 for the other front wheel
Locate the snap pins (14) and large washers (15) from the blister box. Slide the
large washer (15) onto the axle
15 7
15
14
9
14
Snap pin detail
9

9
Assemble the Rear Wheels
1. Note: The right side of the vehicle will only have 1 washer. Locate inner wheel spacer,
snap pins (14) and large washers (15) from the blister box.
Left Rear Wheel
3. Slide the inner wheel spacer (16) onto the axle with the wide end facing out
2. Slide the large washer (15) onto the axle
4. Slide the left rear wheel (8) onto the axle with the gear teeth facing inward
5. Slide the large washer (15) onto the axle
6. Insert the straight side of the snap pin (14) through the hole at the end of the axle
to keep the wheel in place
7. Position the hubcap (9) over the holes on the wheel, and snap the hubcap into place
Right Rear Wheel
8. Slide the right rear wheel (8) onto the axle with the gear teeth facing inward. Ensure
that the gear teeth connect with the gear box that is pre-installed on the axle
9. Repeat steps 5-7
Helpful Tip:
1. If you encounter
wheels onto the rear
axle, then your rear
wheel axle may need
to be realigned.
2. Remove both wheels
from the rear wheel
axle. Using two hands,
push down on the rear
wheel axle and slide
it gently toward the
side of the vehicle that
needs more room.
Fits into
gearbox
16
15 9
814
15
Rear rear wheel detail

10Dashboard/Windshield Assembly
1. Position the two front tabs
on the dashboard above the
slots on the windshield
2. Snap the windshield onto
3. link the connectors assembly
of car body and dashboard
the dashboard
1. Holding the dashboard/
windshield assembly
together, insert steering rod
on the car body through the
hole of the dashboard
2. Align the dashboard with
the slots on the car, and
slide the dashboard into
place
3. Use a Phillips-head
screwdriver to fasten the
dashboard screw (13)
into the two screw hole
locations on either side of
the dashboard
Steering Rod
1313