Hunter Products TR268 User manual

12 Volt 2 Seater
Ride-On
User Manual
Item No #7764, #7757,
#6613, & #6606
Model No: TR268
Maximum user weight is 40kg.
Suitable for ages 3 years+
Please read manual carefully before use.
Please keep the manual and packaging for future reference as
it contains important information.
Adult Assembly Required.
Always wear a helmet and protective clothing when riding.
Continuous adult supervision required when using this product.
Charging the battery can only be done by an adult at all times.
Before rst time use, charge the battery for at least 8 hours.
Please note that this item does not have any sound functions.
Please note that you will require batteries for the light function of
this vehicle.
WARNING: Vehicle must be charged fully before use.
Failure to do so voids warranty

3+years
40 110X76X80cm
12 1000
62
3.5km/h
1.Body 2.Seat
F 15A 240V
3.Windshield
1. SPECIFICATIONS
2. LIST OF PARTS
3. ASSEMBLY PICTURE
4. FUNCTIONS OF VEHICLE AND CIRCUIT DIAGRAM
5. FUSE
6. CHARGING THE VEHICLE
7. TROUBLE-SHOOTING
8. MAINTAINING THE VEHICLE
9. SAFETY PRECAUTIONS
10. DISPOSAL OF BATTERY

4.Steering wheel
12.Charger
7.Back light
9.Screw package:
4pcs 3.5 X12mm screws for
assembling the back lighting
fixture.
10.Screw package:
2pcs 3.5 X12mm screws for
assembling windshield
1.Assemble windshield:
Install the windshield on the vehicle, and
secure in place with 2pcs 3.5X12mm
screws. (See Fig 1)
(Fig.1)
2.Assemble the cover of vehicle bonnet/engine cover.
a:Insert the card mouth of the cover of vehicle head into the slot on
the meter board.(See Fig.2)
8.Steering sleeve
11.Screw and nut for
assembling seat
6.Back section
5.Vehicle bonnet/
engine cover

( Fig.3)
( Fig.2)
b:Pull and turn the locking pins to secure engine cover in place.
(See Fig.3)
3.Assemble the steering wheel:
Place the steering sleeve on the steering wheel rod,then place the
steering wheel on the steering wheel rod.Place the bolt through
the steering wheel and secure with nut.(See Fig.4,5,6)
( Fig.6)
( Fig.5)
( Fig.4)
Insert the back section into the back body of the vehicle,then
secure with 4pcs 3.5 X12mm screws.(See Fig.7,8)
4.Assemble the back section:
( Fig.7) ( Fig.8)
lnsert the two back lights into the back section. (See Fig.7)

4
Place the seat on the vehicle and secure in place by two screws and
nut.(See Fig.9)
5.Assemble the seat:
(Note:please press the nut from underneath the vehicle body hand
when securing the screw.See Fig.10)
( Fig.9) ( Fig.10)
40

1. Body
2. Seat
5
4. S
. Vehicle engine cover
teering wheel
3. Windshield
6. Back section
9. 4pcs 3.5 X12mm screws forassembling
the back lighting fixture.
10. 2pcs 3.5 X12mm screws for assembling windshield
7.Back light
11. Screw and nut for assembling seat
2
5
4
3
6
8
9
11
1
10
11
5
8. Steering sleeve
7

(1).Power switch
(2).Forward and Reverse switch
4.FUNCTION OF VEHICLE AND CIRCUIT DIAGRAM
Battery DC6V 7AH X2
Motor DC12V
FUSE 15A
POWER SWITCH
6

40
15A
7

The charging socket is at the left side of dashboard.
Press the power switch to OFF position to turn the power off.
8

9
PROBLEM POSSIBLE CAUSE
Battery connector is loose.
Make sure the battery connector is firmly plugged in.
The 12 Volt battery will not recharge. Make sure the charger
is plugged into a 240 Volt wall outlet and the power flow to the
outlet is turned on.
Charger is not plugged in. Make sure the charger is plugged into a
240 Volt wall outlet and the power flow to the outlet is turned on.
Check and replace fuse if necessary.
The 12 Volt
battery will
not recharge