Hunter Products Motorized ZP5088 User manual

ZP5088
Warning.Protective equipment should be worn.Not to be used in traffic.
Exhausted batteries are to be removed from the toy.
Rechargeable batteries are only to be charged under
adult supervision.
Warning. Not to be used in traffic.
This toy has no backe.
The toy should be used with caution since skill is
required to avoid falls or collisions causing injury to
the user or third parties.
Batteries are to be inserted with the correct polarity.
Rechargeable batteries are only to be charged under
adult supervision.
Rechargeable batteries are to be removed from the
toy before being charged.
The instruction shall state that transformers or battery
charger used with the toy are to be regularly examined
for damage to the cord, plug, enclosure and other parts,
and in the event of such damage, they must not be used
until that damage had been repaired.
20180328

FORWARD
REVERSE
1
BATTERY: A sealed lead acid battery(6V 4.5AH).
AGE: 18-36 month.
SIZE: 80X50X38cm
LOADING LIMINATION: 20kg
SPEED: 2.5-3km/hr
POWER: Input 110-240V, 50-60HZ, Output 8V
DURATION OF THE BATTERY: Around one hour functioning
with 8-12 hours charging.
1. Please turn on the electric button before use it. turn off while you do not use it.
2. This car has the function of moving forward and back ward. strees forward is
moving forward,stress backward is moving backward.
3. There is a button in the middle of the steer wheel, sounds would come out if
you press this button.
1. Don’t drive this car in the dangerous places such as in the streets,roads and slopes.
2. Don’t ride on sandy or lumpy surfaces.
3. Don’t change the forward/backward switch when the car is still driving.
please change it when the car is stopped.
4. This car is limitted for only one child. overload is prohibited.
5. Battery charging should be operated by adults, children are not allowed to charge the
battery by themselves.
6. This production should be fixed by adults and please check it whether the car is fixed
correctly. It is necessary to be supervised by adults, while child is on riding.
7. Please do not wash the car by water. clean the car with cloth is fine.
8. Please avoid short circuit.

2
TROUBLESHOOTING GUIDE
Problem
The vehicle does not move
The vehicle begins to run slow
The vehicle runs erratically
The charger feels warm when in
use
The gears sound very loud and/or
are making a grinding noise.
Possible Solutions
· Charge the battery. (Charge battery after each use.)
NOTE: vehicle will be cut off electrically during charging.
· Check all electrical connections.
· Check that all switches are in the "on" position
· Check that the foot switch or manual button is not stuck
· The fuse may have been activated due to excessive
weight or rough driving conditions. Wait at least 10~20
seconds, and the vehicle will reset itself.
· Check is whether there is debris stuck wheels.
· Charge the battery. (Charge battery after each use.)
· Only allow one rider at a time.
DO NOT exceed child weight limit: 20kg
· Drive on level ground.
· Battery may be old or not accepting a full charge.
The battery will last from 18 months - 3 years depending
on care, use and environment.
Replace with 6Volt 4.5 Ah battery only.
· Check is whether there is debris stuck wheels.
· There may be a problem with the fuse, or you may
have a damaged battery.
· This is normal.
· The gears may be broken.
1. Please lift up seat connect the main wire to the battery wires before the first time you use it.
Red to red, black to black(see below). It can’t be fixed wrongly, or there will be malfunction
or short circuit.
2. The charging socket placed in front of the seat with a symbol of charging.
3. Please charge it when it is slower than usual.
4. The continued charging time should be no more than16 hours.
5. Please charge the battery fully before you stored it for a long time . And charge
it every three month, this could help extend the lives of the battery.
6. The charger would be a little warm during the charging time, and the battery
would also be a little wet.

3
1
4
8
5
2
6
10 11
14 15
13
12
97
3
Stroller body*1
Mirror*2
M8 Nut*4
10mm Washer*7
M3x16 Tapping Screw*1 M4x40 Machine
Screw*1
M4 Nut*1
7*tresnI1*eldnaH
Hubcap*4 Steering wheel*1 M5x35
Machine screw*1 5mm nut*1
Wheel*3 Driving wheel*1
1*liaT1*taeS
VI.
Charger*1

4
1
6
5
5
5
7
7
7
7
8
8
8
8
9
99
10
10
10
10
10
10
10
3
2
4
4
11
12
12
12
12
12
12
12
13
14 14
VII.

5
5. Set the wheel hub into the front axle in the
direction as shown in the picture;
6. Set the 10MM gasket into the front axle;
7. Screw the M8 lock nut to the front axle with
a wrench.
1. Set the 10MM gasket into the front axle;
2. Set the inserts into the front axle in the
direction as shown in the picture;
3. Set the wheel into the front axle in the
direction as shown in the picture;
4. Set the inserts into the front axle in the
direction as shown in the picture;
4. Set the inserts into the front axle in
the direction as shown in the picture;
5. Set the wheel hub into the front axle
in the direction as shown in the picture;
6. Set the 10MM gasket into the front
axle;
7. Screw the M8 lock nut to the front
axle with a wrench.
1. Set the 10MM gasket into the front
axle;
2. Set the inserts into the front axle in
the direction as shown in the picture;
3. Set the wheel into the front axle in
the direction as shown in the picture;
5
7
8
10
10
12
12
1
5
7
8
10
10
12
12
1
57
810
10
12
12
5
7
8
10
10
12
12
Step 1: Assembly left front wheel
Step 2: Assembly right front wheel

6
4. Set the inserts into the front axle in the
direction as shown in the picture;
5. Set the wheel hub into the front axle in
the direction as shown in the picture;
6. Set the 10MM gasket into the front axle;
7. Screw the M8 lock nut to the front axle
with a wrench.
1. Set the 10MM gasket into the front axle;
2. Set the inserts into the front axle in the
direction as shown in the picture;
3. Set the wheel into the front axle in the
direction as shown in the picture
2. Set the inserts into the rear axle in the
direction as shown in the picture;
3. Set the wheel hub into the rear axle in
the direction as shown in the picture;
4. Set the 10MM gasket into the rear
axle;
5. Screw the M8 lock nut to the rear axle
with a wrench.
1. Set the wheel into the rear axle in the
direction as shown in the picture;
1
5
7
8
10
10
12
12
6
7
8
10
12
1
6
78
10
12
5
7
8
10
10
12
12
Step 3: Assembly left rear wheel
Step 4: Assembly right rear wheel

7
9
99
4
4
Step 5: Assembly left rear wheel
Step 6: Assembly mirror
1. Remove the screws from the steering
wheel first with a Phillips screwdriver;
2. Set the steering wheel into the
direction lever, and align the screw holes
on the steering wheel with those on the
direction lever;
3. Install the screws previously removed
from the steering wheel into the holes of
the steering wheel and direction lever
again, and lock them properly.
Press down the reflector hard against
the hole on the car body in the
direction as shown in the picture.

8
Aim the rear empennage at
the two holes in the rear of the
car body and press it down
hard.
Aim the male tab at the back of the
the seat cushion at the back end
hole of the car body and insert it into
it, and then fix it with a 3x16
mushroom head tapping screw.
2
13
2
13
3
3
Step 7: Assembly seat
Step 8: Assembly tail

8
14
14
Step 9: Assembly handle
1. First aim the rear push stem at the hole in the middle of the rear of the car
body and insert it into the hole;
2. Aim the push stem inserted into the car body at the steering base under the
car body again;
3. Align the push stem holes inserted together with the direction steering base
holes, and then pass the M4x40 screws into the holes, and fix them tightly
with M4 lock nuts.
11
14
14