Hybrid+ FOUR BEAM User manual

User Manual
Please read the instructions carefully before use

1A
TABLE OF CONTENTS
1. Safety Instructions
2. Technical Specifications
3. Installation
4. How to set the unit
5. How to control the fixture
6. DMX512 Configuration
7. DMX512 Connections
8. Trouble shooting
9. Fixture Cleaning

2A
1. Safety Introductions
WARNING
Please keep this User Manual for future consultation. If you sell the fixture to another
user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only,
but always by taking its base.
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try
to repair the fixture by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain
or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light beam while the fixture is on.
Warning
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
Do not open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Caution
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.

3A
There are no user serviceable parts inside the fixture. Do not open the housing or attempt
any repairs yourself. In the unlikely situation, your unit may require service, please contact
your nearest dealer.
2. Technical Specifications
● 4 DMX channels
● 5 Operational Modes: DMX, Master/Slave, auto ,sound activated,IR remote control
● Light Source: 16x3W(4 red, 4 green, 4 blue, 4 amber) LED 50,000hrs
● Power supply: 220 - 240Vac (50-60Hz)
● Power consumption: 50W MAX
● Packing Size:L400×W175×H135mm
● Weight: 2.7kg
3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure
to which you are attaching the unit is secure and is able to support a weight of 10 times of
the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the
unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.
4. How To Set The Unit
4.1 Display and button
Button: ①MENU To select the program function
②UP Increase parameter
③DOWN Reduce parameter
④ENTER Enter submenu

4A
LED: ⑤Signal indicator light of DMX
If the DMX signal was detected , the indicator light flashing.
⑥Signal indicator light of slave
If the slave signal was detected , the indicator light flashing.
⑦Signal indicator light of master
If the program in auto or sound mode, the indicator light is turned on.
⑧Signal indicator light of sound
If the signal of sound was detected , the indicator light was turned on.
Note:(1) In about 10 seconds, if no buttons was pressed, the LED display will be off.
Press any button to turn the display on again.
(2)After pressing a button, all the parameters will be saved after about 2 seconds .
(3)No matter what the program in which mode, once to detect the DMX or SLAVE
signal, the program will jump into DMX or SLAVE mode automatically. Then, if
DMX/SLAVE signal was disconnect, the program will return to the original mode.
4.2 Main Function Chart
5. How to control the fixture
There are two ways to control the fixture
A. Universal DMX controller
B. Master/Slave operation
C. IR remote control

5A
A. Universal DMX controller
The fixture can be set the DMX address remotely by universal DMX controller. First, you
need to programming two scenes into a chase, and then link the fixtures to the universal
DMX controller. When you run the chase, all the fixtures of the chain will be set the series
DMX address automatically. The fixture uses four channels. Please refer to the following
diagram to set the address for the first four units.
B. Master/Slave operation
The fixture will allow you to link 16 fixtures together and operate without a controller. In
Master/Slave mode, the first fixture will control the others to give an automatic, sound
activated, synchronized light show. This function is good when you want an instant show.
The first fixture it’s DMX input cable will have nothing connect it, and the other fixtures will
be set in slave mode automatically. Their DMX input cables connect the last fixture DMX
output cable (daisy chain). Any fixture can act as a Master or as a Slave
C. IR remote control
(1)Auto Chase mode 0 (Chase 1~15 cycle running)
(2)Sound Sound active (to select sound mode 0~12,also by “+” ,”-” to select)
(3) DMX DMX address.(pressing this button about 2s, address=001)
(4) Black Out Switch
(5)Red Red light is turned on
(6)Green Green light is turned on
(7)Blue Blue light is turned on
(8)White Amber light is turned on
(9) + Increase chase run speed,DMX address,sound mode,strobe speed
(10) －decrease chase run speed,DMX address,sound mode,strobe speed
(11) 0~9 To select sound and chase mode with these button correspondence.
Note:In Jump mode, “0” is the chase mode 10.
(12) Jump To select chase 1~12.
(13) Fade To select 3 kinds of gradual mode.
(14) Color To select red,green,blue,amber
(15)Flash Strobe switch.(only effectivity in Auto,Jump,color,RGBA)
NOTE: In DMX mode,the IR remote controller take action until pulling down all handspike for
prevent interference.Then,you can by pressing down “+”,”-”at long time,to increase or

6A
decrease address fast.
6. DMX512 Configuration
4 channel mode
Channel
Value
Function
CH1
0
All light are turned off
1-15
All chase (1~15 ) cycle show
16-255
Chase 1~15 stand alone show
CH2
0-255
Chase speed from slow to fast
CH3
0
None
1-255
Strobe speed from slow to fast
CH4
0
Auto mode (CH1~CH3 effectivity)
0-19
Sound 1~12 cycle running
20-255
Sound 1~12 stand alone
7. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. Connect the fixture together in a “daisy chain” by XLR plug cable from the output
of the fixture to the input of the next fixture. The cable cannot be branched or
split to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system
3. The DMX output and input connectors are pass-through to maintain the DMX
circuit when one of the units’ power is disconnected.
4. At last fixture, the DMX cable has to be terminated with a terminator to reduce

7A
signal errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin
3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
5. Each lighting fixture needs to have an address set to receive the data sent by
the controller. The address number is between 0-511 (usually 0 & 1 are equal to
1).
6. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin1: GND , Pin2: Negative signal (-), Pin3: Positive signal (+)
5 pin XLR: Pin1: GND, Pin2: Negative signal (-), Pin3: Positive signal (+)
Pin4/5: Not Used.
8. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The fixture does not work, no light
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some fixtures don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the fixture. Set the proper address.
D. No response to the sound
1. Make sure the fixture does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone.
9. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.