Hybrid+ HSS 12.6 User manual

User Manual
Please read the instructions carefully before use

1A
TABLE OF CONTENTS
1. Safety Instructions
2. Technical Specifications
3. Installation
4. How to set the unit
5. How to control the fixture
6. DMX512 Configuration
7. DMX512 Connections
8. Trouble shooting
9. Fixture Cleaning

2A
1. Safety Introductions
WARNING
Please keep this User Manual for future consultation. If you sell the fixture to another
user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only,
but always by taking its base.
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try
to repair the fixture by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain
or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light beam while the fixture is on.
Warning
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
Do not open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.

3A
Caution
There are no user serviceable parts inside the fixture. Do not open the housing or attempt
any repairs yourself. In the unlikely situation, your unit may require service, please contact
your nearest dealer.
2. Technical Specifications
Slim PAR 6in1 IR With 12pcs 10W(6 IN 1 RGBWAV) color high brightness LEDs
power supply：220-240Vac / 50-60Hz
fuse：F3A/250V
Power consumption：96W
Channel：6 / 10 DMX channels
Operation mode:Auto, sound Activated,
DMX512, Master/Slave, IR remote control
Dimension：L270×W252×H90mm
Weight：3kg
3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure
to which you are attaching the unit is secure and is able to support a weight of 10 times of
the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the
unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.
4. How To Set The Unit
4.1 Control Panel
①Microphone: Receive music for the sound active.
②MENU: To selected functions
③UP: Increase parameter
④DOWN: decrease parameter
⑤ENTER: Enter submenu
Note:
(1)In 30 seconds, if no button was pressed,the LED
display will turn off. Press any button will turn on the LED display again.The
parameter will not change when the LED display is turned on at first.
(2)Whenever has any button be pressed, program
will save all parameter after 2 seconds,

4A
(3)No matter what the program in which mode,once to detect the DMX or SLAVE signal,
the program will jump into DMX or SLAVE mode automatically. Then,if DMX or SLAVE
signal was disconnect, the program will return to the original mode.
4.2 Main Function Chart
5. How to control the fixture
(1)Black Out Turn on /off
(2)Auto Auto show
(3) Sound Sound active
(4) Strobe Only JUMP, and
Static color mode(The corresponding button is 0~9),
this button has effectivity.
(5) Fade/JUMP:Gradual change mode/Jump change mode switch
(6) Sensitivity: sound sensitivity adjust
(7) R Red dimmer in the dimming mode
(8) G Green dimmer in the dimming mode

5A
(9) B Blue dimmer in the dimming mode
(10) A Amber dimmer in the dimming mode
(11) UV Purple dimmer in the dimming mode
(12) W White dimmer in the dimming mode
(13) + Increase parameter(include strobe speed adjust,sound sensitivity adjust,color
select,adjust the brightness of R,G,B,W,A,UV Gradual change speed adjust,jump change
speed adjust).
(14) R/G/B/A/UV/W/1~9 the device show the same color as the button' s color in the
monochromatic mode
(15) －Reduce parameter(include strobe speed adjust,sound sensitivity adjust,color
select,adjust the brightness of R,G,B,W,A,UV Gradual change speed adjust,jump change
speed adjust).
(16) 0 Function switch(Dimming mode and monochromatic mode)
6. DMX512 Configuration
6 channels Mode:
Channel
Value
Function
CH1
0-255
RED dimmer
CH2
0-255
GREEN dimmer
CH3
0-255
BLUE dimmer
CH4
0-255
WHITE dimmer
CH5
0-255
Amber(Yellow) dimmer
CH6
0-255
Purple(UV) dimmer
10 channels Mode:
Channel
Value
Function
CH1
0-255
Master dimmer
CH2
0-255
RED dimmer
CH3
0-255
GREEN dimmer
CH4
0-255
BLUE dimmer
CH5
0-255
WHITE dimmer
CH6
0-255
Amber(Yellow) dimmer
CH7
0-255
Purple(UV) dimmer
CH8
0-255
Strobe speed ajustable (0: strobe off) in the static color and
jump speed mode.In the gradual mode, the eighth channel
does not work.
CH9
0-255
Static color,Jump speed,Gradual speed or sound sensitivity

6A
CH10
0-59
Custom control by DMX512
60-119
Static mode
120-179
Jump change mode
180-239
Gradual change mode
240-255
Sound mode
7. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. Connect the fixture together in a “daisy chain” by XLR plug cable from the output
of the fixture to the input of the next fixture. The cable cannot be branched or
split to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system
3. The DMX output and input connectors are pass-through to maintain the DMX
circuit when one of the units’ power is disconnected.
4. At last fixture, the DMX cable has to be terminated with a terminator to reduce
signal errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin
3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
5. Each lighting fixture needs to have an address set to receive the data sent by
the controller. The address number is between 0-511 (usually 0 & 1 are equal to

7A
1).
6. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin1: GND, Pin2: Negative signal (-), Pin3: Positive signal (+)
5 pin XLR: Pin1: GND, Pin2: Negative signal (-), Pin3: Positive signal (+)
Pin4/5: Not Used.
8. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The fixture does not work, no light
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some fixtures don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the fixture. Set the proper address.
D. No response to the sound
1. Make sure the fixture does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone.
9. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning

8A
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.