Hybrid+ HMH 7 User manual

User Manual
Please read the instructions carefully before use

1-
TABLE OF CONTENTS
1. Safety Instructions
2. Technical Specifications
3. Installation
4. How to set the unit
5. How to control the unit
6. DMX 512 Configuration
7. DMX 512 Connections
8. Troubleshooting
9. Fixture Cleaning

10

9-
9. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.

2-
Safety Introductions
WARNING
Please keep this User Manual for future consultation. If you sell the fixture to another
user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
Disconnect main power before servicing and maintenance.
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try
to repair the fixture by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain
or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light beam while the fixture is on.
There are no user serviceable parts inside the fixture. Do not open the housing or
attempt any repairs by yourself. In the unlikely event your fixture may require service,
please contact your nearest dealer.
Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.
Direct sunlight can cause heat to build up inside of the unit, which will seriously damage
unit.
Caution
There are no user serviceable parts inside the fixture. Do not open the housing or attempt
any repairs yourself. In the unlikely situation, your unit may require service, please contact
your nearest dealer.
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.

3-
2. Technical Specifications
Featuring 7 high-power 10W Quad-color LEDs.
Each color of R, G, B, W can be controlled individually.
DMX 5/13 channels switchable.
Smooth 0~100% dimming and variable strobe speeds.
5 operation modes: DMX, Mater/Slave mode, Sound Active, auto, dimmer.
Ideal for discotheques, clubs, bars, parties, Mobile DJs, ect.
Input Voltage: 220-240 Vac / 50-60 Hz
Power consumption: 70W
Beam Angle: 45°
Fuse: T 3A
LED: 7 x 10W Quad-color LEDs 60000hrs rated
Dimension: 177 x 177 x 240 mm
Weight: 2.8kg
3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 10
times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is
out of the touch of people and has no one pass by or under it.

8-
5. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
Pin4/5: not used
8. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The fixture does not work, no light
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some fixtures don’t respond to the easy controller
1. You may have a break in the DMX cabling.
2. Check the LED for the response of the master/ slave mode signal.
D. No response to the sound
1. Make sure the fixture does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone.
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.

7-
7. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the
fixture to the input of the next fixture. The cable cannot be branched or split to a “Y”
cable. Inadequate or damaged cables, soldered joints or corroded connectors can
easily distort the signal and shut down the system
2. The DMX output and input connectors are pass-through to maintain the DMX circuit
when one of the units’ power is disconnected.
3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal
errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a
3-pin XLR-plug and plug it in the DMX-output of the last fixture.
4. Each lighting fixture needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

4-
4. How to set the unit
4.1Rear Panel
1Display: To show the various menus and the selected functions
Button:
2 MENU
To select the programming functions
3 UP
To go forward in the selected functions
4 DOWN
To go backward in the selected functions
5 ENTER
Enter submenu
6Mains input: Connect to supply mains power.
7DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal.
8output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

5-
4.2 Main Function Chart
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By DMX controller
5.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when you
want an instant show. You have to set the first unit in Automatic,sound activated mode . Its
DMX input jack will have nothing plugged into it. The other units will have to select A001 ,
Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave led lights will
constantly on.

6-
6. DMX512 Value
5 channel mode:
13 channel mode:
Channel
Value
Function
CH1
0-255
PAN
CH2
0-255
TILT
CH3
0-255
PAN/ TILT speed from fast to slow
CH4
0-255
Strobe speed from slow to fast
CH5
0-255
To select 255 kinds of color
Channel
Value
Function
CH1
0-255
PAN
CH2
0-255
PAN Fine
CH3
0-255
TILT
CH4
0-255
TILT Fine
CH5
0-255
PAN/ TILT speed from fast to slow
CH6
0-255
Strobe speed from slow to fast
CH7
0-255
Red dimmer
CH8
0-255
Green dimmer
CH9
0-255
Blue dimmer
CH10
0-255
White dimmer
CH11
0
CH7~CH10 effectivity
1-255
To select 255 kinds of color
CH12
0
Custom control by DMX512
1-84
Slow running
85-169
Fast running
170-255
Sound mode
CH13
255
Reset

11