Hybrid+ TRIPLE DERBY User manual

User Manual
Please read the instructions carefully before use

Safety Introductions
WARNING
Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they
also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by
yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light beam while the fixture is on.
There are no user serviceable parts inside the fixture. Do not open the housing or attempt any repairs by
yourself. In the unlikely event your fixture may require service, please contact your nearest dealer.
Due to the magnifying type lens, please keep the lens out of contact with direct sunlight. Direct sunlight can
cause heat to build up inside of the unit, which will seriously damage unit.
Caution
There are no user serviceable parts inside the fixture. Do not open the housing or attempt any repairs yourself. In
the unlikely situation, your unit may require service, please contact your nearest dealer.
1.Specification
Control Mode: DMX, Master/Slave, sound activated, Auto
8CH DMX control
High output butterfly beam effects 24 sharp beams
Built-in programmed lighting show
4 Digital LED Display panel
LED Color: RGBW
Power Supply: 100V-240Vac,50- 60Hz
Power Consumption: 25W
Light Source:4pcs 5-watt RGBW Color LEDs
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.

2. Operation at display
Led display state
Ｘ＝random display
（0－9）＝（selection section）
8．8。8。8。
FUNCTION
Fixture state
MENU
UP
DOWN
ENTER
MENU：function selection
Axxx - - - S2xx
UP / DOWN: adjust the parameter
ENTER: Confirm the selection
Please press enter to keep the operation
Indicate light flicker：
There is signal input
S A V E
（when DMX signal detected ）Synchronous
mode
Slave mode
AＸ Ｘ Ｘ
（when DMX signal detected）Master can
change to DMX512 mode Automatically.
---Set the DMX512 Address by （A001--A511）
DMX512 mode
Ａ1 1---9
Red activated
Master
fixture
Auto
Running
with
built-in
program
Can output
synchronous
Signal to slave
ones
Ａ2 1---9
Green activated
Ａ3 1---9
Blue activated
Ａ4 1---9
White activated
Ａ5 1---9
LED-single-color jump change
Ａ6 1---9
Multi-color jump change
Ａ7 1---9
Multi-color fade change
Ａ8 1---9
Multi-color flash change
Ｓ1 1---20
Sound Mode 1
Master
fixture
running
in sound
mode
Ｓ2 1---20
Sound Mode２

3. DMX-512 --7CH mode DMX table
Channel
Value
Function
CH1
0---255
Master dimmer
CH2
0--255
Red dimmer
CH3
0--255
Green dimmer
CH4
0--255
Blue dimmer
CH5
0--255
White dimmer
CH6
0--9
No strobe
10-255
Strobe from fast to slow
CH7
0--5
Motor stop
6-127
Motor orientation running
128-255
Motor auto running speed from slow to fast
CH8
0--9
Control by DMX
10--72
Multi-Color Fade change from slow to fast
73--134
Multi-Color Jump change from slow to fast
135-197
LED Single Color Jump change from slow to fast
198--220
Sound mode 1
221--255
Sound mode 2
3. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of
dirt on the fixture’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.