HySecurity SlideDriver 15 User manual

Programming & Operations Manual
with
HySecurity Smart Touch Controller
MX3630-01 Revision B
SlideDriver 15, 30F, 40, 80, 200
and SlideDriver 50VF 2/3
This document provides Important Safety Information, specications, and references along with
an overview of programming user and installer menu options, designing vehicle loop layouts,
troubleshooting, and maintaining the gate operator.

HySecurity Gate OperatOrS: uL 325 – 2016
The following bullet points highlight how your automated gate system sites can monitor external entrapment
protection using HySecurity gate operators:
• Normally Closed (NC) sensors – Before gate movement occurs, the gate operator veries that the
external entrapment protection sensor is connected and fully functional.
• Build Year (BY) – An added menu item distinguishes between pre-2016 manufacturing dates and
UL 325 - 2016 manufacturing dates. Build Year (BY) is a factory-setting. Build Year 2 (BY 2) is the default for
all HySecurity gate operators indicating a manufacturing date of 2016 in the serial number. Replacement
controller boards for existing sites allow for a Build Year setting of 1 (BY 1) (pre-2016).
• Independent Sensor Inputs – The edge, photo eye and photo eye COM inputs on the Smart Touch and
Smart DC Controllers (STC and SDC) have been re-labeled. The same wiring connections become three
independent methods for easy entrapment sensor conguration and normally closed outputs.
Table 1: HySecurity Gate Operators requiring External Monitored Entrapment
Protection Sensors
HySecurity Gate Operators
(includes Modular, Correctional, and
UPS models)
Build Year
UL 325 - 2016
(set at the factory)
UL 325 Entrapment Protection Sensor Monitoring Required
Normally Closed (NC) sensors tested & approved.
Three SENSOR Inputs on Controller.
Installer Menu congurable.
Build Year (BY) factory-set to UL 325 - 2016.
SlideDriver 15, 40, 30F, 50VF 2/3, 80, 200 2 ●
SlideDriver 50VF series 2 ●
SlideSmart DC 15 & DCS 15 2 ●
SlideSmart DC 10F & DCS 10F 2 ●
SwingRiser 14, 14-Twin, 19,
19-Twin, 30, 30-Twin 2●
SwingSmart DC 20 & DCS 20 2 ●
HydraSwing 40, 40F, 40-Twin, 40F-Twin,
80F, 150 2●
HydraLift 10, 10F, 20, 20F 2 ●
Table 2: HySecurity Gate Operators maintaining Object Detection
Table 2 indicates those HySecurity gate operators that may be within the exception parameters of UL 325 or
comply with standards other than UL 325, but continue to maintain object detection capabilities. HySecurity
strongly recommends that you assess every site for entrapment zones and provide the necessary protection to
guard against entrapment.
HySecurity Gate Operator's with
Obstruction Protection (Object Detection)
Build Year
UL 325 - 2016
Sensor Inputs automatically set to "NOT USED"
Installer has option to change settings as site design dictates.
StrongArm (HTG) 14, 20, 28, 36 2 ●
StrongArmCRASH (M30/M50) 2 ●
StrongArmPark DC 10 & DCS 10
StrongArmPark DC 14 & DCS 14 2●
WedgeSmart DC 10 & 10 DCS 2 ●
WedgeSmart DC 14 & 14 DCS 2 ●
HydraWedge SM50 2 ●
ii MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com

Table 3: External Entrapment Protection Sensors Approved for Use with HySecurity
Gate Operators
The site designer or installer must determine which external entrapment protection sensors will be installed
with the gate operator to create a UL 325 compliant installation site.
NOTE: Table 3 provides the list of sensors that are approved for use with HySecurity gate operators using the monitoring
capabilities found in software versions h4.53 or h5.54 (or higher). These sensors are ETL listed or UL recognized to UL 325 and have
been tested and approved by Intertek for use in HySecurity gate operators.
External Entrapment Protection Sensors: Normally Close Contact, Compatible with
HySecurity Gate Operators
P/N 2016 Monitored Sensors Sensor Type Output Manufacturer UL 325
Recognized
MX3981
MX4161
Wired Gate Edge Sensor
MGR20-2U-05-T2, Round
Wraparound edge
(5 ft x 2" round post) 10K Resistor
Miller Edge Type B2
Gate Edge Module (GEM -204) Edge Interface Module Normally Closed
MX3982
MX4161
Wired Gate Edge Sensor
MGS20-2U-05-T2, Square
Wraparound edge
(5 ft x 2" square post) 10K Resistor
Miller Edge Type B2
Gate Edge Module (GEM -204) Edge Interface Module Normally Closed
MX4037
MX4161
KIT: Wired Gate Edge Sensor
MGO20-2E-05-T2, Square
and Channel mount
Edge (3-sided activation
Slide In Style)
(5 ft x 1½" width)
10K Resistor
Miller Edge Type B2
Gate Edge Module (GEM -204) Edge Interface Module Normally Closed
MX3985 Reecti-Guard (RG-R) Photo eye, reective Normally Closed Miller Edge Type B1
MX4015 KIT: MGL-K20
(includes MX3986 and MX4013) Wireless Gate Link Normally Closed Miller Edge Yes
MX3986
MX4013
Wireless Gate Link
MGL-TX20
Transmitter (battery-
operated, radio control) N/A
Miller Edge Yes
Wireless Gate Link
MGL-RX20
Receiver (24VDC, radio
control) Normally Closed
MX3987 The Solution, MIM-62 Multi-Input Module Normally Closed Miller Edge Yes
MX3990 IRB-MON (Dist.~ 65 ft) Thru-beam photo eye Normally Closed EMX
Industries Type B1
MX000846 KIT: IRB-325 (Dist.~ 50 ft) Thru-beam photo eye Normally Closed EMX
Industries Type B1
MX000999 KIT: E3K-R10K4-NR (Dist. ~ 40 ft) Photo eye, reective Normally Closed Omron Type B1
NOTE: Bold type indicate sensors or accessories that must be installed together for external entrapment protection to be properly
monitored.
www.hysecurity.com © 2017 Introduction MX3630-01 Rev. B iii

SlideDriver 15, 30F, 40, 80, 200
SlideDriver 50VF Site Installation Overview
iv MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com
Gate Face*
Use shims as needed
Grooved Drive Rail
Gate Wheel Cover
Support Post
SlideDriver
Height from top of
Drive Rail* to bottom
of gate operator.
All models:
9¼" (23.5cm) using
All models:
(except SD 200)
26" (66cm)
SlideDriver 200:
43¼" (109.5cm)
Wheel Cover
Drive Rail
Support Post
Concrete Pad
SlideDriver
For clarity, safety mesh
is not shown
Drive
Rail
Screen Safety Mesh on Gate Height: Per UL 325 and ASTM
F2200, all openings in a sliding gate up to a 72-inch (6 foot or
183 cm) height must be guarded or screened.
standard
AdvanceDrive™ wheels, 6 or 8 inch.
*NOTE: using XtremeDrive™wheels, adjust
height along the length of the Drive Rail by
¼ to ½ inch which increases overall height
between 9¾ and 10 inches (24 to 25 cm).
Limit
Ramp

SlideDriver (all models) 50VF Components
UC2
USAGECLASS
Board, Display
Detector, Vehicle
Board, Smart Touch
Board, Power Supply
Cable, Ribbon
Transformer
Contactor, Motor
Switch, Disconnect
Reset Switch, Internal
Reset Button, External
Board, Display
HY-5A Detector, Vehicle
Board, Smart Touch
Board, Power Supply
Transformer
Variable
Frequency Drive
(VFD) Power Unit
Switch, Disconnect
Reset Switch, Internal
Reset Button, External
SlideDriver 50VF Control Box
[Motor, Electric] Buzzer, Piezo
Keypad
[Pump Pack]
Drive Arm, Pivot Kit
AdvanceDrive™ Wheel Kit
Drive Arm, Motor Mount, Top
Motor, Hydraulic
Release,
Manual
Drive Arm, Motor Mount, Bottom
Chassis
Cover not shown
Limit
Switches
Hose
SlideDriver Control Box
Combination AdvanceDrive
and XtremeDrive Wheels
(80 and 150 Models, only.
Not available on 50VF series)
www.hysecurity.com © 2017 Introduction MX3630-01 Rev. B v

Motor, Electric, AC
Motor, Electric, DC
Motor Starting Kit
Contactor, Mercury
Valve, Relief
Sensor Kit, Inherent Entrapment
Valve Coil, Quick Stop
Reservoir
Valve Coil, Directional
Valve, 2 Position Directional
Gauge, Pressure
Valve, Check, Endhead
Valve, Quick Stop
Quick Disconnect, Socket
Braking Kit
Valve, Braking
Vent plug
AWOG
Vent plug
Breather cap
SlideDriver (all models) 50VF Components
vi MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com

Contents
HySecurity Gate Operators: UL 325 – 2016.....................................................................................................................ii
Table 1: HySecurity Gate Operators requiring External Monitored Entrapment Protection Sensors ...........................ii
Table 2: HySecurity Gate Operators maintaining Object Detection.............................................................................ii
Table 3: External Entrapment Protection Sensors Approved for Use with HySecurity Gate Operators ......................iii
Welcome to HySecurity...........................................................................................1
Contact Information .........................................................................................................................................................2
Notices and Bulletins .......................................................................................................................................................2
Supplemental Documents................................................................................................................................................2
IMPORTANT SAFETY INFORMATION.............................................................................................................................3
Safety - Additional Installer Responsibility....................................................................................................................4
Identifying Gate Operator Category and Usage Class ....................................................................................................5
Safety - Additional Installer’s Responsibility, continued................................................................................................6
Safety - Owner/User Responsibility...............................................................................................................................7
Hazardous Materials and Proper Disposal .......................................................................................................................7
Emergency Stop Button ..................................................................................................................................................8
Emergency Release .........................................................................................................................................................8
Safety Notices ..................................................................................................................................................................9
Common Industrial Symbols ............................................................................................................................................9
PoWer ..................................................................................................................11
Installing the Earth Ground ...........................................................................................................................................11
Site Considerations.....................................................................................................................................................12
Wiring AC Power............................................................................................................................................................12
Turning the Power Switch ON.....................................................................................................................................13
Wire Sizing and Runs......................................................................................................................................................14
Low Voltage Control Wiring........................................................................................................................................14
SlideDriver Wiring Charts (Incoming Power)...............................................................................................................15
SlideDriver 50VF-series Wiring Chart (Incoming Power).............................................................................................17
Performance of 50VF-series Operators on 1 and 3 Phase, 50 or 60Hz.......................................................................17
Control Transformer Connections (Non-UPS) ...............................................................................................................19
Gate Operator Connections (Modular Unit) ..................................................................................................................19
DC Power Supply (UPS) Connections.............................................................................................................................20
AC Power Supply with HyInverter AC ............................................................................................................................20
initial SetuP..........................................................................................................21
Gate Handing.................................................................................................................................................................21
Hydraulic Hose Swap .....................................................................................................................................................22
Adjusting the Brake Valves ............................................................................................................................................22
www.hysecurity.com © 2017 Table of Contents MX3630-01 Rev. B vii

Grounding, Breather Cap Installation & Handing .........................................................................................................23
SlideDriver Slow Down Limit Ramps ...........................................................................................................................24
Adjusting the Pressure Relief Valve ................................................................................................................................25
ModBus RTU in SlideDriver 50VF-series ........................................................................................................................26
Emergency Fast Operate (EFO) in SlideDriver 50VF-series ...........................................................................................27
Installing a Push Button Device for Emergency Fast Operate (EFO) ............................................................................28
Emergency Fast Close Speeds ...................................................................................................................................28
entraPment Protection .........................................................................................29
Manufacturer’s responsibility..........................................................................................................................................29
Pressure Relief Valve – All Hydraulic Operators: ........................................................................................................29
Inherent Entrapment Sensor System – Hydraulic Operators (IES) ..............................................................................30
The Inherent Entrapment Sensor (IES) ..........................................................................................................................30
How Software Handles Monitoring External Entrapment Protection Sensors ...............................................................31
Table 4: Changes to Sensor Inputs on the Controller.................................................................................................31
External Entrapment Protection Sensors: What the Installer Needs to Do....................................................................31
Table 5: Installer Menu Settings for SENSOR Inputs ..................................................................................................33
Supply Power to the Sensors .........................................................................................................................................34
control Panel overvieW .......................................................................................35
SlideDriver Wiring Diagram, D0266 REV B ....................................................................................................................36
Variable Speed Drive (VFD) Control Box .......................................................................................................................37
Variable Speed Drive Wiring Diagram ...........................................................................................................................38
STC Board, Power Supply Board and Display................................................................................................................39
DiSPlay & menu oPtionS........................................................................................41
Initial Setup ....................................................................................................................................................................41
Understanding the Display and Keypad .......................................................................................................................41
Menu Mode and the STC Keypad ................................................................................................................................42
Menu Mode Navigation .................................................................................................................................................42
Run Mode and the STC Keypad ...................................................................................................................................43
Viewing Operator Status Displays..................................................................................................................................43
Stop the Status Display Scrolling................................................................................................................................44
Change the Contrast on 7 Segment Displays.............................................................................................................44
Check the Software Version ........................................................................................................................................44
Check Time and Date .................................................................................................................................................45
User Menu......................................................................................................................................................................45
User Menu: Table 6 ........................................................................................................................................................46
Installer Menu ................................................................................................................................................................48
Installer Menu: Table 7 ...................................................................................................................................................48
Setting the Close Timer .................................................................................................................................................54
Test the Operator...........................................................................................................................................................55
viii MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com

Stc inPutS & Wiring.............................................................................................57
Overview of the STC and Power Supply Board..............................................................................................................58
Integrating with Security Systems and HyNet™ Gateway .............................................................................................59
Smart Touch Controller Inputs........................................................................................................................................60
STC Terminal Inputs .......................................................................................................................................................60
User Relays – Programming Procedure ..........................................................................................................................63
Programmable User Relays: Table 8............................................................................................................................63
Hy8Relay Module Option...............................................................................................................................................66
Bi-Parting & Dual gate SyStemS ............................................................................67
Connecting an Interlocked Pair (Dual Gate)...................................................................................................................67
Dual Gate Wiring Connections ...................................................................................................................................68
Dual or Sequenced Gates: Power, Software & Accessory Requirements ..................................................................69
Programming a Dual Gate (Interlocked Pair) .............................................................................................................69
Connecting Sequenced Gates .......................................................................................................................................70
Sequenced Gate: Conguration #1 ...............................................................................................................................72
Sequenced Gate: Conguration #2 ...............................................................................................................................73
veHicle Detector
inStallation anD logic ...........................................................................................75
Anti-TailGate Mode (Closing Logic) ............................................................................................................................75
TailGate Alert .............................................................................................................................................................75
Vehicle Detector Installation: HY-5A ..............................................................................................................................76
Connecting HY-5A Vehicle Detectors.............................................................................................................................77
View Call Level in Real Time .......................................................................................................................................78
Installing Standard 11-Pin Box Type Vehicle Detectors..................................................................................................79
PHoto eye inStallation ..........................................................................................81
Photo Eyes (Non-Contact) Installation ...........................................................................................................................82
Compatibility ..............................................................................................................................................................82
Installation...................................................................................................................................................................82
Conguration ..............................................................................................................................................................83
Photo Eye Connections: Smart Touch & Smart DC Controllers ..................................................................................83
Photo Eye Function.....................................................................................................................................................83
Retro-Reective Photo Eye Systems ..................................................................................................................84
Using Photo Eye Sensors instead of Vehicle Loops ......................................................................................................85
Photo Eye Alignment Feature .......................................................................................................................................86
inStalling gate eDge SenSorS.................................................................................87
Compatibility ..............................................................................................................................................................88
Installation...................................................................................................................................................................88
Gate Edge Function....................................................................................................................................................88
www.hysecurity.com © 2017 Table of Contents MX3630-01 Rev. B ix

trouBleSHooting ...................................................................................................89
System Diagnostic Messages.........................................................................................................................................89
Troubleshooting Codes: Table 9.................................................................................................................................90
Access the Event Log through the User Menu ..............................................................................................................95
Electrical Issues ..............................................................................................................................................................96
AC-Powered Gate Operators......................................................................................................................................96
Mechanical Issues...........................................................................................................................................................97
Hydraulic Issues..............................................................................................................................................................97
Typical Problems and Troubleshooting Procedures .......................................................................................................98
general maintenance ...........................................................................................99
Smart Touch Analyze and Retrieve Tool (S.T.A.R.T.) .......................................................................................................99
What You Need...........................................................................................................................................................99
Installing S.T.A.R.T. Software.......................................................................................................................................99
Software Maintenance..................................................................................................................................................100
Electrical Controls ........................................................................................................................................................100
Clock Battery Replacement ......................................................................................................................................100
Mechnical Controls.......................................................................................................................................................101
Stopping the Gate ...................................................................................................................................................101
Starting the Gate .....................................................................................................................................................101
Mechanical Maintenance .............................................................................................................................................101
Drive Rail...................................................................................................................................................................102
Drive Wheel Spring Tension (Adjustment of Manual Release)..................................................................................103
Grooved Drive Rail ...................................................................................................................................................104
Drive Wheel Assembly..............................................................................................................................................105
Hydraulic System Maintenance....................................................................................................................................106
Brake Valve Adjustments .........................................................................................................................................107
Pressure Relief Valve Adjustments ............................................................................................................................107
Open Valve ...............................................................................................................................................................107
SlideDriver Operator Maintenance Schedule ..............................................................................................................108
Wiring HySecurity SenSorS: Smart toucH .............................................................109
Wiring Tips for SENSOR COM Terminal: Smart Touch ................................................................................................110
Menu Mode Navigational Tips.....................................................................................................................................110
Smart Touch: Wired Edge Sensor with GEM (-104)......................................................................................................111
Smart Touch: Photo Eye Thru Beam (EMX IRB MON)..................................................................................................112
Smart Touch: Photo Eye / Reective (E3K R10K4) .......................................................................................................113
Smart Touch: The Solution, MIM-62 (Multi-input Module)...........................................................................................114
Smart Touch: Photo Eye / Reecti-Guard (RG-R)..........................................................................................................115
Smart Touch: Wireless Edge, Wireless Gate Link.........................................................................................................116
Smart Touch: Wired Edge with GEM-104 & Photo Eye ...............................................................................................117
Smart Touch: WireLess Edge Gate Link & Photo Eye ..................................................................................................118
SlideDriver Installer Checklist.......................................................................................................................................119
Specications ...............................................................................................................................................................120
xMX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com

www.hysecurity.com © 2017 Important Safety Information MX3630-01 Rev. B 1
Welcome to HySecurity
Thank you for purchasing our premium SlideDriver™ gate operator. HySecurity Gate, Inc. has manufactured
some of the nest, sturdiest, most innovative, and reliable hydraulic gate operators since the 1970s. We use the
same hydraulic technology common in the aircraft industry while incorporating software capabilities that far
exceed the competition.
All operator designs are tested for hundreds of thousands of cycles before being released to the market. Slide,
swing, trafc barrier, fortied crash barrier and vertical lift operators have all received rigorous testing and
certication. Security, low maintenance, exible conguration, and overall toughness are the foremost criteria
for all HySecurity products.
Our commitment to quality and innovation will become evident as the features and performance of the
expertly engineered and manufactured SlideDriver become familiar to you. Thank you again for the condence
you’ve shown in becoming part of the HySecurity family and in choosing a premium, industry-leading product.
HySecurity Gate, Inc. Headquarters in Kent, WA

2MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com
cOntact infOrmatiOn
Qualied HySecurity distributors are experienced and trained to assist in resolving any problems. For the name
of a qualied distributor near you, call HySecurity at 800-321-9947.
Before contacting your distributor or HySecurity Technical Support, obtain the serial number of your operator.
For information about HySecurity training for installers, maintenance personnel, and end users, refer to the
company website at www.hysecurity.com.
nOticeS and BuLLetinS
Installers should visit HySecurity’s online Technical Support page at www.hysecurity.com or contact HySecurity
prior to installing product to make sure they have received the most up-to-date information.
SuppLementaL dOcumentS
The product literature is comprehensive and contains information needed to plan, install, operate and maintain
your gate operator. Additional general information concerning HySecurity gate operators can be obtained
from the following:
• The gate safety section of the HySecurity website contains published materials regarding industry
changes due to UL 325 - 2016 requirements involving external entrapment protection sensors.
• Links to the product catalogs, product order form, operator manuals, operator software downloads,
technical support bulletins and other useful information.
• S.T.A.R.T. User’s Guide (D0049) - Smart Touch Analyze and Retrieve Tool - details the extensive
software, diagnostic and troubleshooting capabilities of the Smart Touch Controller board.
• DC Power Supply with HyCharger DC, supplement
• AC Power Supply with HyInverter AC, Installation and Reference Manual
• Technical Bulletins (as applicable).
NOTE: Technical Bulletins are automatically issued to registered users of HySecurity products. The product
warranty registration card can be lled out online at www.hysecurity.com.

www.hysecurity.com © 2017 Important Safety Information MX3630-01 Rev. B 3
impOrtant Safety infOrmatiOn
WARNING
Read all the product safety information prior to installation. Automatic gate operators move the gate with high
force and can cause serious injury and death! Make sure the automatic gate operator is installed to reduce the
risks of entrapment. Verify the gate operator is installed to comply with all safety standards and local and federal
regulations.
Understand that you as the site designer, installer, maintenance crew, or owner/user must consider the risks
associated with automatic gate operators. Hazards exist with automatic gate operators and can be reduced
with proper gate site design, installation and use. Installers, maintenance crews, and owners/users must
take responsibility to read and follow the safety requirements and Important Safety Information found in the
HySecurity product manuals and review all the literature that accompanies the product.
It is important that only qualied installers handle the installation of the HySecurity equipment and gate
operator. A “qualied” installer has one of the following:
• A minimum of three years experience installing similar equipment
• Proof of attending a HySecurity Technical Training seminar within the past three years
• Signicant manufacturer endorsements of technical aptitude in automatic gate operator installation
and operation
Underwriter Laboratories (UL) and the American Society for Testing and Materials (ASTM) are responsible for
current safety standards and regulations regarding automatic vehicular gate operators. To pass certication, all
aspects of gate operator and gate installation must comply with the appropriate safety standards.
For the most up-to-date ASTM F2200 Gate and Fence Standards, refer to www.astm.org.
For UL 325 Standard of Safety, refer to www.ul.com.
SAVE THESE INSTRUCTIONS

4MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com
impOrtant Safety infOrmatiOn
WARNING
A moving gate or barrier arm, bollard, or wedge can cause serious injury or death.
To reduce the risk of injury or death:
1. READ AND FOLLOW ALL INSTRUCTIONS. Read the gate operator’s product manual and review all the product
labels and literature prior to installing, operating, or maintaining the automatic gate operator.
2. Never let children operate or play with gate controls. Keep all remote controls, especially radio transmitters, away
from children. Do not allow children to play on or around the gate or gate operators.
3. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING
GATE. Start the gate operator only when a gate’s travel path is clear.
4. Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object
activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Perform
routine tests of the entrapment protection sensors, such as photo eyes and gate edges. Failure to adjust and
retest the gate operator properly can increase the risk of injury or death.
5. Use the emergency release only when the gate is not moving.
6. KEEP GATES PROPERLY MAINTAINED. Read the product manuals. Have a qualied service person make repairs
to gate hardware and replace batteries in accessory or entrapment sensory devices on a regular basis.
7. The automated gate entry is for vehicle use only. Pedestrians must use a separate entrance. Make sure a separate
walk-through entrance is nearby. Make certain a clear pedestrian path is designated and signs direct pedestrians
to the walk-through gate.
8. Install the supplied WARNING signs on the inside and outside of the gate or barrier gate/operator so they are
clearly visible from both the secure and public sides. Installing the signs is a requirement for UL 325 compliance.
9. Use monitored sensors for protection against entrapment as specied in the current UL 325 Standard of Safety.
Safety - Additional Installer Responsibility
• The gate operator must be properly grounded and the incoming power voltage must match the voltage label on
the junction box.
• Verify and install an automatic gate operator per its usage class and only on gate sites that comply with ASTM
F2200 Gate and Fence Standards. See Identifying Gate Operator Category and Usage Class on page 5.
Screen or enclose openings in the gate and install sensors to monitor potential entrapment areas per UL 325
Standard of Safety, which includes:
• All horizontal slide gates must guard or screen openings from the gate’s base support to a minimum height of
6 feet (183 cm) above the ground. This must prevent a sphere of 2¼ inches (57 mm) in diameter from passing
through an opening in the gate or the adjacent fence that is covered in the gate’s open position.
• Physical stops must exist in the gate construction to prevent over-travel in both directions and, for slide gates,
guard posts must be installed to prevent the gate from falling in the event of a roller failure. Exposed rollers
must be capped to avoid potential entrapment.
• Make sure all exposed pinch points are eliminated or any exposed pinch points, rollers and wheels are
guarded.
• External entrapment protection sensors must be used wherever the risk of entrapment exists.
SAVE THESE INSTRUCTIONS

www.hysecurity.com © 2017 Important Safety Information MX3630-01 Rev. B 5
identifyinG Gate OperatOr cateGOry and uSaGe cLaSS
Gate operators are given a usage class according to UL 325 Standard of Safety. The usage class is determined
by the area that the vehicular gate operator services.
Four different vehicular usage classes are dened by UL 325:
Class I
Class I: Intended for use in garages or parking areas associated with a residence
of one to four single families.
Class II
Class II: Intended for use in a commercial location or building such as a multi-
family housing unit (ve or more single family units) hotels, garages, retail stores
or other buildings accessible by or servicing the general public.
Class III
Class III: Intended for use in an industrial location or building such as a factory
or loading dock area or other locations NOT accessible by or intended to
service the general public.
Class IV
Class IV: Intended for use in a guarded industrial location or building such as
an airport security area or other restricted access locations, NOT servicing the
general public, in which unauthorized access is prevented via supervision by
security personnel.
SAVE THESE INSTRUCTIONS

6MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com
impOrtant Safety infOrmatiOn
Safety - Additional Installer’s Responsibility, continued
• Before attaching the operator to the gate, move the gate or barrier gate in both directions. Make sure it is level
and moves freely. A gate or barrier gate that moves easily reduces strain on operator components. Gravity should
play no part in the opening or closing of a slide gate.
• Never over-tighten a clutch or pressure relief valve to compensate for a stiff or damaged gate.
• Reduce the risk of entrapment throughout the entire travel path by making sure the gate is installed in a location
which ensures the required clearance between the gate and adjacent structures when opening or closing. On
slide gates, minimize the parallel gap between the gate and the fence.
• Install the gate operator on the secure (non-public) side of the gate. Note that swing gates cannot open into
public areas.
• Install external entrapment protection sensors so pedestrians are protected from entrapment in both directions
of gate travel and all hazard areas are fully protected. On hydraulic gates, set the pressure relief valve at the
lowest allowable setting that will reliably operate the gate. The pressure relief valve controls the applied
force of the operator and the sensitivity of the inherent entrapment sensor (IES). Note that no IES exists in the
StrongArm.
• Never disable the Warn Before Operate buzzer. This buzzer provides an alert that the gate is about to move.
• Mount access control devices beyond reach of the gate. The control devices that operate the gate must:
• Be mounted beyond 6 feet (183 cm) of the gate to prevent users from touching or accessing the gate while
operating the controls. People attempting to access the controls by reaching through or around the gate can
be seriously injured or killed by the moving gate.
• Incorporate a security feature to prevent unauthorized use.
• Connect radio and other remote access (non-resetting controls) to the RADIO OPTIONS terminal.
• Be located in a clear line of sight to the gate. Locate access controls (Open, Close, Stop/Reset) where a user
will have a clear view of the gate.
NOTE: An exception for Emergency Access Control devices exists. An EAC device accessible by
authorized personnel only (e.g. re, police, EMS) may be placed at any location within the line-of-sight.
• Open and close the gate to conrm that it was properly installed and to ensure monitoring sensors are working
correctly. Verify the clearance between the gate and adjacent structures per UL 325 Standard of Safety. Have a
qualied technician test the gate monthly.
• When you complete the installation, demonstrate the safety features and operation of the gate operator to the
end user:
• Clearly explain and demonstrate the consequences of removing or defeating any of the safety features.
• Remove the operator cover(s), and then turn the power on and off.
• Manually release the gate. (Use the manual release only when the gate is NOT moving.)
• Use the Emergency Stop Button. (If an emergency stop button is not available, show the user where the Stop
button is located on the gate operator.)
NOTE: Gate operator instructions must be given to the owner per UL 325 Standard of Safety.
• Take photographs of the completed installation site and save it in your business les.
SAVE THESE INSTRUCTIONS

www.hysecurity.com © 2017 Important Safety Information MX3630-01 Rev. B 7
impOrtant Safety infOrmatiOn
Safety - Owner/User Responsibility
As the owner/user, you are responsible for the correct and safe installation, operation and maintenance of the
SlideDriver gate operator. It is of the utmost importance that you read and follow the specic instructions and
precautions found in the IMPORTANT SAFETY INFORMATION addressed in this manual. In addition, you must
adhere to the safety standards of applicable federal, state, and local safety regulations, industry standards,
and/or procedures.
NOTICE: For installations outside the United States, make sure that you follow the applicable international,
regional, and local safety standards.
• Automatic gates are for vehicular use only; provide and maintain walkways and signs to direct pedestrians to a
separate walk-through entrance.
• An automatic gate can start at any time without warning; always keep people away from the gate area.
• Never let children operate or play with gate controls. Keep all remote controls, especially radio transmitters, away
from children. Do not allow children to play on or around the gate, gate area, or
gate operators.
• Learn how to turn the power on and off. Learn how to manually operate the gate.
• WARNING signs supplied with the gate operator must remain installed and clearly visible on both sides of the
gate. The signs are required to maintain UL 325 compliance.
• Do not physically disable the warning buzzer and NEVER disconnect or cut its wires. The buzzer provides
compliance with the Manual on Uniform Trafc Control Devices (MUTCD) standards. Disabling the warning
buzzer may increase the risk of death or serious injury.
• Do not remove entrapment protection sensors or any other safety features.
• Have a professional gate installer routinely inspect the gate hardware and test the entrapment protection sensors
and overall gate operation. Have a qualied service person make repairs to gate hardware and equipment to
keep the gate running smoothly.
HazardOuS materiaLS and prOper diSpOSaL
Be aware of the international, federal, and local codes in your area and how best to handle hazardous waste
materials.
The pump pack uid, found in all hydraulic HySecurity operators, can be recycled. Gear oil, found in HySecurity
electromechanical gate operators, can also be recycled. If the uids are mixed or contaminated with any
solvents or other chemicals, they become hazardous waste. Hazardous waste requirements for storage and
disposal must be followed.
CAUTION
If the gate operator has a battery backup system, the batteries contain materials that are considered hazardous
to the environment. Proper disposal of the battery is required by federal law. In the U.S.A., refer to federal EPA
guidelines for proper hazardous waste disposal.
SAVE THESE INSTRUCTIONS

8MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com
emerGency StOp ButtOn
Make sure all users of the gate know where the emergency stop
button is located (see illustration). It complies with UL 325 Standard
of Safety requirements.
Pressing the emergency stop button while the gate is opening or
closing disables the automatic close timer and stops gate travel.
Gate travel remains stopped until the operator receives another
open or close signal.
emerGency reLeaSe
WARNING
Before attempting a manual release, the gate cannot be moving and the power must be disconnected.
Make sure and teach all users how to turn
off electric power, how to move the gate
manually, and how to release the drive
wheels.
Know the weight of the gate you are moving.
Excessively heavy gates can be difcult
to move and may cause serious injury to
those involved in moving the gate. Take
the necessary precautions when manually
moving any gate.
To disengage the drive wheels from the drive
rail and manually move the gate, take the
following steps:
1. Remove the front chassis cover and
set it aside.
WARNING
Emergency Stop
button
Toggle Handle
clamped
Drive
Wheels
Drive Rail slides between
drive wheels
Toggle Handle
unclamped
When releasing the handle inside the chassis, be careful as the mechanism is spring-loaded and drops
rapidly. Hold the handle appropriately so your ngers do not get injured or pinched.
2. Pull the toggle handle down. The manual release is located under the electric control panel and to the
right of the hydraulic motors.
NOTE: For more information, refer to Drive Wheel Spring Tension (Adjustment of Manual Release) on page 101.
Other types of release mechanisms exist. For example, the Fire and Emergency Access Lock Box is available
through HySecurity distributors. Contact your distributor for more information.

www.hysecurity.com © 2017 Important Safety Information MX3630-01 Rev. B 9
Safety nOticeS
The following four levels of safety notices are used where applicable within this manual; each notice contains
information specic to the situation.
DANGER
Indicates death or serious injury will occur if the hazardous situation is not avoided.
WARNING
Indicates death or serious injury could occur if the hazardous situation is not avoided.
CAUTION
Indicates mild or moderate injury could occur if the hazardous situation is not avoided.
NOTICE: Indicates damage to equipment is probable if the hazardous situation in not avoided.
cOmmOn induStriaL SymBOLS
The following international safety symbols may appear on the product or in its literature. The symbols are used
to alert you to potential personal injury hazards. Obey all safety messages that follow these symbols to avoid
possible injury or death.
Attention
- Take Note -
- Danger -
Keep Away
Entrapment
Zone
Possible
Pinch Point
Ground
Symbol
O
Electrical Phase
Symbol

10 MX3630-01 Rev. B SlideDriver/SlideDriver 50VF Series © 2017 www.hysecurity.com
Page intentionally left blank