Hytronik HMW31 User manual

24.5
HMW31
1-10V Dimming with Remote Control
IP65 High Bay HF Motion Sensor
Hytronik Microwave motion sensor
313
IP65RED
Stand-by power
EMC standard (EMC)
Safety standard (LVD)
Certication
Radio Equipment (RED)
Resistive
EN55015, EN61000
Semko, CB, CE , EMC, RED, RCM
EN60669-1, EN60669-2-1
Model No. HMW31
120~277VAC 50/60Hz
Mains voltage
Load ratings:
EN300440, EN301489-1,
EN62479
<1W
Input Characteristics
Safety and EMC
400VA@120V; 800VA@220 -277V
800W@120V; 1600W@220 -277V
Capacitive
Sensor Data
HMW31
Operation temperature Ta: -20
O
C ~ +70
O
C
Environment
IP65
IP rating
Model No.
<0.2mW
5.8GHz +/- 75MHz
High Frequency (microwave)Sensor principle
Operation frequency
Transmission power
Detection range
Detection angle
Max. ( Ox H) 10m x 15m
20sWarming-up
Technical Data
360O
Mechanical Structures and Installations
For more details, please refer to user manual.
HF
www.hytronik.com
A. Ceiling mount
91.5
59.3 57.3
47.5
4.1
80.7
75
4.1
66.6
81.5
Sensor module
Daylight sensor
LED indicator
Infrared receiver
Rotary switch
Cable entry
Installation rack

Hytronik Microwave motion sensor
314
Intelligent Photocell (daylight detection prior to motion detection)
1
The built-in photocell will also automatically turn off the light when the ambient natural light exceeds the programmed lux level for
more than 5min, regardless of whether motion is detected or not. This feature can be disabled if it is required that the xture stays at
dimmed level during absence.
With insufcient natural light, the sensor
switches on the light automatically when
presence is detected.
With sufcient natural light, the light
does not switch on when presence is
detected.
The sensor switches off the light when
natural light is sufcient, even with
presence.
Note: if the stand-by time is preset at "+∞", the xture never switches off but stays at preset dimming level even when natural light is sufcient.



%FUFDUJPO1BUUFSO
"NCJFOUEBZMJHIU
UISFTIPME
0OF,FZ
$PNNJTTJPOJOH
1IPUPDFMM
*OUFMMJHFOU
3PUBSZ4XJUDI
1SPHSBNJOH
Functions and Features
www.hytronik.com
C. Attach to the shade by clamp
B. Screw to the Luminaire by conduit 59.6
66.6
89.9
0.825”
75 64
59.3 57.3
35.2
47.5
th sufcient natural li
g
ht, the li
g
i
h
h
th insufcient natural li
g
ht, the
s
i
h
h
li
h
i
l
l
T
he sensor switches off the li
gh
ll
ih
i
f
i
Sensor module
Daylight sensor
LED indicator Infrared receiver
Rotary switch
Angle adjustment
Luminaire clamp
84.5
59.3
ぶ
29
163.2
66.6
75
33.7
15
28.5
4.5
ぶ
4.5
59.6
Sensor module
Daylight sensor
LED indicator
Infrared receiver
Rotary switch
Cable entry

Hytronik Microwave motion sensor
315
Tri-level Control (Corridor Function)
2
Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas which require a light change notice
before switch-off. The sensor offers 3 levels of light: 100%-->dimmed light (natural light is insufcient) -->off; and 2 periods of
selectable waiting time: motion hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.
zero-cross point
Alternating current
Zero-cross Relay Operation
Designed in the software, sensor switches on/off the
load right at the zero-cross point, to ensure that the
in-rush current is minimised, enabling the maximum
lifetime of the relay.
3
A rotary switch is built inside the sensor for scene
selection / fast programming. Total 16 channels
are available:
Rotary switch preset
Rotary Switch Preset
Note: settings can also be changed by remote control
HRC-11. The last action controls.
0 5s100% Disable
1 1min100% 2Lux
2 5min100% 10Lux
3 5min100% 30Lux
4 5min100% 10Lux
5 5min100% 30Lux
6 5min100% Disable
7 10min100% 2Lux
8 10min100% 10Lux
9 10min100% 30Lux
A 10min100% Disable
B 10min75% 30Lux
C 10min50% 10Lux
D 30min100% 50Lux
E30min100% Disable
F5s100%
10%
10%
10%
10%
Disable
10%
30%
10%
10%
10%
30%
10%
10%
10%
30%
10%2Lux
10s
5min
10min
30min
0s
+∞
+∞
10min
30min
+∞
+∞
+∞
+∞
+∞
+∞
10s
Detection
range
Channel Hold-time Stand-by
time
Stand-by
dim level
Daylight
sensor
Wiring Diagram
Detection Pattern
Ceiling mounted height(m)



10%
30%
75%
50%
HMW31
Brown
LED driver
L
N
1-10V+
1-10V
L
N
Blue
Grey
Red
Black
-
www.hytronik.com

Hytronik Microwave motion sensor
316
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
Settings (Remote Control HRC-11)
Press button “RESET”, all settings go back to rotary switch settings.
Reset Settings
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
Note: “Semi-auto” function is disabled.
ON/
OFF
Power output
Press the buttons to adjust the light brightness during hold-time.
Load Indication:
The light will ash ONCE rapidly after
receiving the commamd from the
remote control successfully.
Brightness +/-
Scene program - 1-key commissioning
Detection range
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: To set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button rst.
Daylight threshold
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
www.hytronik.com
&
A

III
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button
The mode will change to AUTO Mode after power failure.

Hytronik Microwave motion sensor
317
1. Press button “Shift”, the red LED starts to ash.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.
Ambient daylight threshold
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Dual tech & RF mode
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the stand-by dimming level
when no presence after motion hold-time.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
All buttons are disabled.
www.hytronik.com
Auto-conguration function
All buttons in this zone are disabled.