IBM WD1003-WA2 User manual

k\
WD 1 OO3-WA2
USER ’ S GUIDE
-019
V a ■ * A i I
■ ■ ■ • Vv.' •
/-I
■
.r' j ■ ■ ■
I
j ■■ ' ' ;
I
I
I
: ■ ? ■ ' W

WD 1003- WAS
USER ’ S GUIDE
-019

TABLE of contents
*
*
*
*
*
*
registered trademark of International
WD1003-WA2 JUMPER SETTINGS ............................
SOFTWARE INSTALLATION ....................................
FORMATTING THE WINCHESTER DISK .................
1. PROCEDURES ........................................................
2. WINCHESTER DISK DRIVE TYPES ......................
3. PREFORMATTiNG THE WINCHESTER DISK . . .
. PARTITIONING THE WINCHESTER DISK ...........
LOCKING BEFORE MOVING ....................................
MS-DOS INTRODUCTION ..........................................
SIMPLE DOS COMMANDS ..........................................
1
2
3
3
8
9
1
1
17
23
IB* PC/XT/ at is a ’
Business Machines Corp.

WD1003-WA2 JUMPER SETTINGS
■'QT
00
•c in to
WWcq
U10
n
El THROUGH E6
WD1003-WA2 JUMPER LOCATIONS
EB
E7 E8
WD1003-WA2 JUMPER SETTINGS
DESCRIPTION
Standard factory setting. Selects primary addresses.
E2 to E3
Standard factory setting. Selects primary addresses.
E5 to E6
Selects secondary addresses.
El to E2
E to E5
Selects secondary addresses.
Standard factory setting.Supports 360 RPM floppy disk drives.
E7 to E8
Jumper in this position selects 300 RPM floppy disk drives.
E8 to E9
“ 1 -
PIN
CONNECTS
E7
E8
E9
HMM
mnm
loool
D
NOTE
DO NOT MOVE PRIMARY ADDRESS JUMPERS UNLESS
YOUR OPERATING SYSTEM IS CONFIGURED TO ACCEPT
TOW HARD DISK CONTROLLERS. CERTAIN OPERATING
SYSTEMS SUPPORT TWO CONTROLLERS IN THE SAME
SYSTEM. IBM DOS AND MANY IBM-COMPATIBLE OPER 
ATING SYSTEMS DO NOT SUPPORT THIS FEATURE.
J6 1

1. Insert your system Diagnostic Diskette (or equivalent).
2. Turn on th6 power.
3. Boot Diagnostic and select setup option.
. Set clock etc.
(
— 2 —
7. Insert System Diagnostic Diskette (or equivalent) after
the system finishes the low level Format.
CAUTIO
Avoid system damage by consulting your
> ensure
by
all
Technical Reference manual to
that your drive type is supported
your Host BIOS drive 'tables. ot
■ 1 -compatibles share the same drive ta 
bles as IBM.
NOTE
Step 6 requires execution of low level formatting. Use of
the IBM Advanced Diagnostic (or similar program for IBM
-compatibles) is necessary since these controllers contain
no on-board Basic Input/Output System (BIOS)ROM.
S. Select proper Drive Type. Consult your Technical Re 
ference Manual for further information on these param 
eters.
SOFTWARE INSTALLATION
This section contains instructions for preparing (low level
format, etc.) your operating system to recognize the Wes 
tern Digital controller.
Load and execute the FDISK and FORMAT programs.
Follow instructions in your reference manual.
6. Insert your Advanced Diagnostic diskette and execute
low level Format. Follow instructions in your reference
manual.

FORMATTING THE WINCHESTER DISK
1. Procedures
2. Setting Up The System Parameters
2.1 Setting Up Procedures
SELECT AN OPTION
- 3-
Set Up The System Parameters
Preformat The Winchester Disk
Partition The Winchester Disk
Format The Winchester Disk
$
*
*
*
A.
B.
C.
D.
From the PC/AT supplier you have an IBM Advanced
Diagnostics diskette. By this diskette you can set
up the system parameter as follows:
A. Boot the IBM Advanced Diagnostics Program
and your will get the display as follows;
***##«« ««*******^«*^*«* *#*#**$« #^*********« «««$
*
♦
♦
♦
*
*
♦
*
♦
*
♦
♦
♦
♦ ♦
SELECT THE ACTION DESIRED
? 4 (CR)
0 - Y TEM CHECKOUT
1 - FORMAT DI KETTE
2 - COPY DI KETTE
3 - PREPARE Y TEM FOR MOVING
4 - ETUP
9 - END DIAGNOSTICS
Before a Winchester <jlisk drive could be used please follow
the procedures to prepare your Winchester disk drive for
operation.

J
The following options have been set:
1
-4-
*
♦
*
♦
♦
♦
♦
*
*
*
512KB
OKB
Your system may have other options
installed. They are not required for
Setup and are not displayed.
Diskette Drive A - High Capacity
Diskette Drive B - Not Installed
Fixed Disk Drive C - Type
Fixed Disk Drive D - Not Installed
Base memory size
Expansion mamory size - -----
Primary display is attached to:
- Monochrome Display Adapter
Are these options correct (Y/N)
? N (CR)
After your selecting option H W you will be rom ted to enie *
the current date and time and you will come to e
following display:
♦♦♦♦♦♦♦♦^♦♦♦♦♦♦♦♦♦♦♦♦^♦♦♦♦♦♦♦******************************** ?l
♦
♦
♦
♦
♦
♦
♦
♦
*
♦
*
♦
*
*
♦
*
♦
*
♦
*
*
♦
♦
*
*
*
♦
*

Press "ENTER ” to continue ...
?
(CR)
♦
*
♦
*
-5-
*
*
*
♦
*
♦
»
Diskette Drive B is set for a
Double Sided Drive.
Your diskette drive types
are set to the following :
System options Information is
required to answer the following
questions.
♦
♦
*
♦
*
*
*
♦
♦
*
♦
♦
♦
*
♦
♦
*
♦
*
*
*
♦
Are diskette drive types correct (Y/N)
? N (CR)
Is Diskette Drive B a High
Capacity drive (Y/N)
? N (CR)
Is Diskette Drive A a High
Capacity drive (Y/N)
? Y (CR)
Is there only 1 diskette drive
installed (Y/N)
? N (CR)
Diskette Drive A - High Capacity
Diskette Drive B - Not Installed
If the default options are not the same as your existing
configuration you should answer "N" and you can proceed as
follows to set up your configurations:
♦
♦
♦
*
*
♦
*
*
^^t*****^*^**************#*******************************
*
*
♦
*
*

♦
How many fixed disks are installed?
1
WARNING
«»
*
*
Fixed Disk Drive C - Type 2
Fixed Disk Drive D - Not Installed
You have set your fixed disk
drive types to the following :
Enter fixed disk type (1-15)
for Fixed Disk Drive C.
You have set your fixed disk
drive types to the following :
*
♦
♦
*
*
♦
*
Enter 0, 1, or 2 for the number
of fixed disk drives installed.
’ 1 (CR)
- 6 -
Press "ENTER" to continue ...
? (CR)
Is this correct (Y/N)
’ N (CR)
Is this correct (Y/N)
? Y (CR)
Entering the wrong drive type
causes improper operation of
the fixed disk.
? 2 (CR)
«
»
♦
*
*
♦
*
*
*
*
»4tH««««fM««»«tt«<«*****«**«»***«*t*****«f*»*4 l «*****t««4«*
Fixed Disk Drive C - Type 1
Fixed Disk Drive D - Not Installed
Now you have set up diskette drive A as a
type drive arid diskette drive B as a 1
drive.
After Pressing (CR) you will come to the above prompt.
Again you can answer "N" to configure your own set
-up and you can continue as follows:
i Hig-h Capacity
Double sided