IBM 3196 Manual

----
----
- - ---
- ---
-- ---
- -----
-----
--_ .-
IBM 3196 Display Station
Setup Instructions
GA 18-2488-2
Part Number 81 X5374
" i

IBM 3196 Display Station
.
Setup Instructions
GA 18-2488-2
Part Number 81 X537 4
File Number S5250/36/38-06

Federal Communications Commission (FCC) Statement
Warning: This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used
in accordance with the
instruction manual, may cause interference
to radio communications.
It has been tested and found to comply with the limits for a Class A
computing device
pursuant to Subpart J of Part 15 of FCC Rules,
which are designed
to provide reasonable protection against such
interference when operated in a commercial environment. Operation
of this equipment in a residential area is likely to cause interference
in which case the user at his own expense will be required to take
whatever measures may be required
to correct the interference.
The above FCC statement applies only to those machines used in the
U.S.
SAFETY PRECAUTION
An improperly wired outlet or plug can place hazardous
voltages on accessible metal parts of this display station. The
power cord and plug (when supplied)
on your display station
have been approved for use with this display station and meet
the necessary testing laboratory/test house standards. For your
safety, the power cord and plug must be connected to a properly
wired and grounded outlet. The customer
is responsible for the
outlet and plug wiring.
If it becomes necessary to change power cord or plug or if the
outlet
is improperly wired, have the change made by a qualified
electrician according to local or national code. A new power
cord may be ordered from your IBM sales representative.
Third Edition (April 1987)
This major revision obsoletes GA 18-2488-1. Changes are made occasionally to the
information herein; any su ch changes will be reported in subsequent revisions.
Reference in this publication to IBM products , programs , or services does not imply
that IBM intends to make these available in all countries in which IBM operates. Any
reference to an IBM program product in this publication is not intended to state or
imply that only IBM's program product may be used. Any functionally equivalent
program may be used instead.
Publications are not stocked at the address given below . Requests for IBM
publications should be made to your IBM ' representative or to the IBM branch office
serving your locality .
A form for readers ' comments is provided at the back of this publication . If the form
has been removed , comments may be addressed to IBM Corporation , Publications
Development , Department 6R1J, 180 Kost Road, Mechanicsburg, PA 17055 U.S.A. IBM
may use or distribute whatever information you supply in any way it believes
appropriate without incurring any obligation to you.
© Copyright International Business Machines Corporation 1986, 1987

Section 1. Inventorying the Elements
No tools are necessary for setting up your display station.
If you have any problems in setting up the IBM 3196 Display Statlon,see the IBM 3196 Display Station
Problem Solving Guide, GA18-2483.
Check each box (0 ) as you unpack and identify each item.
If any are missing , call your IBM marketing representative .
Section 1. Inventorying the Elements 1

oVideo Element
o Video Stand
oKeyboard oKeyboard Overlay
oLogic Element
o Auto - Termination Unit
2 IBM 3196 Setup

o
Security Keys
(inserted
in the logic element)
o Video Cable
o Power Cord
o IBM 3196 Display Station
User 's Guide ,
GA18-2482
User's
Guide
o IBM 3196 Display Station
Problem Solving Guide,
GA18-2483
Notes:
o
X-ray Label
(Germany Only)
0,. on d,esem Gerlt enls'ehenOil
RiSnlgenSUlhlung lSI lu"eoc:hend
ebgesch"mt BescM.umgungs~nnu"9
unlet 20kV
o Repair Identification (RID) Tags
(located on
the underside of the
logic element)
o Safety Label
(Spain Only)
NOABRIR SIN
t~
ANTES OESCONEC·
TAR LA TENSION
OERED
!m •• KV
(Il •••• v 1E •••• Hz 1iI ••• W
[ !x~M l
--_ .-
1. Save all packaging material for use if service is required ,
2.
Record the security key identification number in case the keys are lost and replacement is needed.
3.
Store one of the security keys in a safe place .
Section 1. Inventorying the Elements 3

4 IBM 3196 Setup

Section 2. Setting Up the Display Station
Be sure you have met the installation requirements of the IBM 3196 Display Station Description , GA18-2481,
and the
IBM 5250 Information Display System Planning and Site Planning Guide , GA21-9337, before seHing
up your display station.
2.1 ATTACHING THE TAGS TO YOUR VIDEO ELEMENT, LOGIC ELEMENT, AND KEYBOARD
ELEMENT.
Note: IBM uses the Repair Identification (RID) tags to determine the maintenance status of your
display station. Without these tags, service may be delayed or unobtainable .
2.1.1 Turn the
logic element upside down .
Section 2. Setting Up the Display Station 5

2.1.2 Remove the tags from the underside of the logic element.
Note: The tags and their location may not appea r exactly as shown .
I 2.1.3 Turn the logic element right side up.
6 IBM 3196 Setup

2.1.4 Peel off the tags and place one on each of the elements in the locations shown below.
r - - German Only. - ,
Ole In d.esem Ger;;1 enlSlflFlende
Fl ontvenst,"h1u"i '5 1 lIu5.e ,C hend
, bgesch .. ml B esch l eun ''iIun'ilSSOllnnu ng
unle.2010.V
I I
L
______ ...J
(Front View )
r - -Spain Only- - ,
I NO A BRI R SIN f ill I
I
~;~ ~~~ ~ 7o'::' C I
I DE RED I
. .. KV
I 1IJ .. .. v 1iI .... H' 1il .. .W ,
I...------~
(Bo ttom View)
Section 2. Setting Up the Display Station 7

2.2 ATTACHING THE VIDEO STAND TO THE LOGIC ELEMENT.
2.2.1 Place the
circular port i on of the video stand in the circular recess on top of the logic element, and
align the notch and tab.
2.2.2 Pinch in the two latches to lock the video stand into the logic element ; then release the latches.
8 IBM 3196 Setup

2.2.3 Check the video stand to make sure it is securely locked into the logic element.
Section 2. Setting Up the Display Station 9

2.3 ATTACHING THE LOGIC ELEMENT TO THE VIDEO ELEMENT.
2.3.1 Turn the video element upside down.
Note: Make sure the video screen faces you.
CJ
¢- <D 0 1
1
([[UU 'J 'J [[[-_ . . _rr~[[[t([[ J
[[(([(1- : .. -....:.:..:.--:~ -=--rl([m
I
lllllll~ ~ ~ --=:- :: ==1
lllllJ 1
1lI1111l1Il1LL _ . . --m '" ,-.. J1Illll
10 <D -l;f
2.3.2 Locate the five slots on the bottom of the video element.
10 IBM 3196 Setup

2.3.3 Locate the five hooks on the top of the video stand.
2.3.4
Turn the logic element upside down and insert the five hooks on the video stand into the five slots
on the video element.
Section 2. Setting Up the Display Station 11

2.3.5 Hold the front side of the video element, and push the logic element forward (in the same direction
the screen faces) until the video stand snaps into place.
2.3.6 Make sure the video stand is locked into the video element by trying to move the logic element
forward and backward.
12 IBM 3196 Setup

2.3.7 Turn the video element right side up.
o
o
Section 2. Setting Up the Display Station 13

2.4 CONNECTING THE VIDEO AND KEYBOARD CABLES.
2.4.1 Insert the plug on the video cable into the socket on the video element and the logic element, then
tighten the screws .
Note:
The video cable is permanently attached to some video elements.
2.4.2 Remove the cap from the keyboard cable plug, hold the plug so that the IBM logo is facing up,
then
insert the plug into the socket on the front of the logic element.
Note: Your keyboard may be different in appearance from the one shown .
14 IBM 3196 Setup

2.5 PREPARING THE DISPLAY STATION FOR POWER-ON.
2.5.1 Make sure that the power switch is set to off (0).
2.5.2 Insert the power cord plug into the power socket on the rear of the video element.
Section 2. Setting Up the Display Station 15

SAFETY PRECAUTION
An improperly wired outlet or plug can place hazardous voltages on accessible metal parts of this display
station. The power cord and plug (when supplied) on your display station have been approved for use with
this display station and meet the necessary testing laboratoryltest-house standards. For your safety, the
power cord and plug must be connected to a properly wired and grounded outlet. The customer is
responsible for the outlet and plug wiring.
If It becomes necessary to change power cord or plug or if the outlet is improperly wired, have the change
made according to local or national code. A new power cord may be ordered from your IBM sales
representative.
Notice For Customers in Chicago, Illinois: Two different lengths of power cords, 1.8 m (5 .9 ft) and 2.8 m
(9.2 tt), are shipped with the IBM 3196 Display Station. Do not use the 2.8 m (9.2 ft) power cord; use a 1.8 m
(5.9 tt)
power cord .
2.5.3 Plug the power cord into a grounded electrical outlet.
2.5.4 Make sure the security key is inserted in the keylock and turned clockwise.
16 IBM 3196 Setup