IDTECK Star FINGER006 User manual

Table of Contents
ii
Table of Contents
1 Safety Information
1 IMPORTANT SAFETY INSTRUCTIONS
2 General
3 Features
4 Specification
5 Identifying Supplied Parts
6 Product Overview
1 Functions
1.1 Registration Mode
1.2 Reader Mode
1.3 Card Number Input Format
1.4 Card Number Output Format
1.5 *1OK Signal Output (Applicable when output setting is 26/34bit Wiegand, Open colle
ctor Output)
1.6 Error Signal Output (Applicable when output setting is 26/34bit Wiegand, Open collec
tor Output)
1 * In normal mode, the FGR006 transmits Card ID only when authorization is a success. But if you set
‘Extension mode’ by application software, the FGR006 transmits Card ID also when authorization is fail
ed. In this case, you can get information of users whose authorization is failed. However, because a Ca
rd ID is transmitted to the controller, users who failed authorization of the FGR006 can get access to a
door depending on setting of the controller. (Default is Normal Mode)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

p.iii
1.7 Dual Finger Mode
2 Product Explanation
2.1 Panel Description
2.2 Color Coded & Wiring Table
7 Installation Tips & Check Points
1 Recommended Cable Type and Permissible Length of Cable
2 Reader Connection
8 Installation of the Product
1 Mullion and Wall Mount
2 System Initialization
2.1 For 8.0.0 and higher version of FGR006 / 8.1.0 and higher version of IP-FGR006 / 4.0.
0 and higher version of FGR006SR
2.2 For lower version of 8.0.0 FGR006 / lower version of 8.1.0 IP-FGR006 / lower version
of 4.0.0 FGR006SR
3 FGR006 Network Configuration
4 Wiring
4.1 Power Connections
4.2 Input Connection
4.3 Output Connections
4.4 External Reader Connection
9 Communication
1 Board ID Setting for RS485 / RS422 Communication
1.1 For 8.0.0 and higher version of FGR006 / 8.1.0 and higher version of IP-FGR006 / 4.0.
0 and higher version of FGR006SR
1.2 For lower version of 8.0.0 FGR006 / lower version of 8.1.0 IP-FGR006 / lower version
of 4.0.0 FGR006SR
2 RS232 Communication Connection
3 RS485 Communication Connection
4 RS422 Communication Connection
10 Operation
1 Master Card Registration Mode
1.1 Master Card Registration
1.2 Master Card Change
1.3 Master Card Function.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table of Contentsp.iv
2 Registration Mode
2.1 Registration Mode Function
2.2 User Card Registration.
RF + FINGER MODE:
RF Only:
3 Reader Mode
3.1 Reader Mode Function.
3.2 Authorization
RF + FINGER MODE:
RF-ONLY MODE:
4 Identification Mode
4.1 IDENTIFICATION MODE:
5 External RS232C Stereo Jack (Option)
11 Operating Status of FGR006
1 LED Indicators Status
2 Beeper Sound Status
12 Output Format
1 26bit Wiegand Output Format
2 34bit Wiegand Output Format
3 Normal Output Mode (Default)
4 Extension Output Mode (Selectable using the software)
13 Troubleshooting
1 IDs have been transmitted from software to the device, but I cannot access.
1.1 Please check if IDs have been transmitted to controller, too.
2 The device does not go to setting mode after reading MASTER ID.
2.1 MASTER ID may have changed.
3 The device dose not communicate with PC.
3.1 Please check wiring.
In the case of RS232 communication
In the case of RS485 communication
3.2 Please check if the communication ID is good.
Check communication address setting of software and the device.
3.3 Please check if the communication port setting is good.
4 I want to access with card only, without fingerprint.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

p.v
4.1 If you registered a fingerprint, newly registered the ID without fingerprint.
5 Errors keep occuring when registering a fingerprint.
5.1 Check if the status of the fingerprint is good.
5.2 Place your fingerprint on the right position of the fingerprint scanner.
6 I want to access with fingerprint only, without card.
6.1 Please check if IDENTIFICATION mode is set to "USE".
7 A fingerprint is not recognized.
7.1 Please check the status of the fingerprint.
7.2 If the status of the fingerprint is OK, register your fingerprint again.
8 I want to register 2 fingerprints for 1 ID.
8.1 Please check if Dual Fingerprint Mode is set to "USE".
14 FCC REGISTRATION INFORMATION
15 RMA Request
. . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . 41
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Safety Information 1
p.1
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIE
D SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is pres
ent within this unit.
This exclamation point symbol is intended to alert the user to the presence of importa
nt operating and maintenance (servicing) instructions in the literature accompanying the ap
pliance.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet. Usin
g any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,

p.2
electric shock, or damage to the product.
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cau
se abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may caus
e fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may ca
use personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or container
s filled with water on top of the controller. Doing so may cause personal injury due to fi
re, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or el
ectric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued us
e in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disass
emble or modify this product in any way. (SAMSUNG is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may ca
use fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a locat
ion subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (b
elow -30°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to d
o so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liqui
ds, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any tim
e.

Safety Informationp.3
1IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s ins
tructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two bla
des and a third grounding prong. The wide blade or the third prong is provided for you
r safety. If the provided plug does not fit into your outlet, consult an electrician for repla
cement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenie
nce receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sol
d with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparat
us combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparat
us has been damaged in any way, such as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the apparatus has been expo
sed to rain or moisture, does not operate normally, or has been dropped.

General 2
p.4
The Star FGR006 / iPASS IP-FGR006 / IDTECK FGR006SR is a Fingerprint Identification Proxi
mity Reader which can be connected to a control panel. The Star FGR006 / iPASS IP-FGR006
/ IDTECK FGR006SR provides high level security by integrating functions of proximity reader
and fingerprint identification, and permitting access only when card ID and a fingerprint are
matched.
It is easy to install on metal mullions or flat surfaces, and its elegant design and credible fing
erprint recognition technology give you full satisfaction.

Features 3
p.5
●1:1 Verification and 1:N Identification
○Identification Method: by Auto Touch Sensor
○Verification Method: by 1:1 Matching of Card and Fingerprint
●125 KHz Proximity and Fingerprint Recognition
●1,000 / 2,000 / 4,000 Fingerprint Users (Selectable)
●Various Operating Modes
○RF Only/ Fingerprint Only/ RF + Fingerprint
●RF Only mode is provided for users whose fingerprints are not applicable.
●Fingerprint Registration/Deletion and Reader Mode Setting using Master Card
●Network Communication via RS232 / RS422 / RS485 (Max.255ch)
●Upload Fingerprint Templates to PC, Download Fingerprint Templates from PC
○Optional RS232C Stereo Jack is required
●Output format : 26bit Wiegand (Default) and ABA Track II (Option)
●1ea of External Reader Port
○26/ 34bit Wiegand, ABA TRACK II and 4 / 8bit Burst Signal Reception
●High Protection from Scratch and ESD (Electro Static Discharge)
●High Quality Optical Sensor
●Tamper Switch for theft prevention
●Option: RS232C Stereo Jack
●Compatible Software: STARWATCH DUAL PRO I / II, STARWATCH iTDC PRO I / II FINGE
RPRINT ENROLLMENT PRO
●Compatible Controller: iCON100, iTDC, iMDC, Third Party Standalone Controller
●Comparison Table

p.6
FGR006 PSK Format, Built-in 125KHz (4”) Proximity Reader
RF Only / *Fingerprint Only / RF+ Fingerprint
IP-FGR006 ASK[EM] Format, Built-in 125KHz (4”) Proximity Reader
RF Only / *Fingerprint Only / RF+ Fingerprint
FGR006SR Built-in 13.56MHz (4”) Contactless Smart Card Reader
Smart Card Only / *Fingerprint Only / Smart + Fingerprint
* NOTE: Auto Touch Sensor is optional for some product depending on their versi
on.
FGR006 v7.4.0 or above, IP-FGR006 v8.1.0 or above and FGR006SR v 3.3.0 or abo
ve: Auto Touch Sensor is included.
FGR006 below v7.4.0, IP-FGR006 below v8.1.0 and FGR006SR below v 3.3.0: Aut
o Touch Sensor is optional.

Specification 4
p.7
Model FGR006
CPU 32bit ARM9 and Dual 8bit Microprocessor
Memory Fingerprint
Module
Program Mem
ory
1MByte Flash Memory
Data Memory 1MByte/ 4MByte Flash Memory
8MB SDRAM
Controller Program Mem
ory
128KByte Flash Memory
Data Memory 256KByte Serial Flash Memory, 4KByte SRAM
Fingerprint User 1,000 / 2,000 / 4,000 Fingerprint Users
Fingerprint Template Size 800 Bytes for 2 Fingerprint Templates
Read Rang
e
Passive Type FGR006 IDK50 / IMC125: Up to 2 inches (5cm)IDC80 / IDC170:
Up to 4 inches (10cm)
IP-FGR006 IPK50: Up to 2 inches (5cm)IPC80 / IPC170: Up to 4 inc
hes (10cm)
FGR006SR ISK50 / IHC80 / IMC135: Up to 2 inches (5cm)ISC80: Up
to 4 inches (10cm)
Reading Time (Card) 30ms
Verification / Identification Time Less than 1sec. / Less than 2sec.
Power / Current DC 12V / Max. 350mA
FGR006 /
IP-FGR006
1 port
(4/8bit Burst for PIN, 26bit Wiegand, ABA Track II)
FGR006SR 1 port

p.8
(4/8bit Burst for PIN, 34bit Wiegand, ABA Track II)
Communication RS232 / RS422 / RS485 (Max.255ch)
TCP/IP (External LAN Converter Required)
Baud Rate 9,600bps (Recommended) /
4,800bps, 19,200bps and 38,400bps (Selectable)
Input Port 3 ports (LED Control In,
Buzzer Control In, Tamper Switch)
Output Port 3 ports (Error Signal Out,
OK Signal Out, Tamper Switch Out (Open Collector Out
put))
LED Indicator / Beeper 3 LED Indicators (Red and Green) /
Piezo Buzzer
Operating Temperature Fingerprint Mo
dule
-20 to +60C (-4 to +140F)
RF Reader -35 to + 65C (-31 to +149F)
Operating Humidity 10% to 90% relative humidity non-condensing
Color / Material Pearl Dark Gray and Light Gray / Polycarbonate
Weight /
Dimension (W x H x T)
259.5g (0.57lbs) /
66mm x 129mm x 52mm (2.6” x 5.1” x 2.0”)
Certification FCC, CE, KC
●Finger Module Specification
Resolution 500dpi
Capture Image Size 356 X 292 pixels
Extraction Image Size 248 X 292 pixels
Sensing Area 12.7 X 14.9mm
Scanner High Quality Optical Sensor
FAR(False Acceptance Ratio) 0.001%
FRR(False Reject Ratio) 0.1%
ESD(Electro Static Discharge) 15KV
Verification Time Less than 1sec.
Identification Less than 2sec.

Identifying Supplied Parts 5
p.9
Please unpack and check the contents of the box.

Product Overview 6
p.10
1Functions
1.1 Registration Mode
In the registration mode, you can register new user cards or delete existing cards. You need
a Master Card to enter the Registration Mode.
1.2 Reader Mode
In Reader Mode, you can choose either RF Only mode or RF+FINGER mode. You need a Mas
ter Card to enter the Reader Mode. There are 2 kinds of Reader Mode as below.
-RF Only Mode: In this mode you need only card authorization to obtain access. If
card authorization is successful the corresponding card number will be transmitted
to the controller. This mode is useful for the user whose fingerprint is not applicabl
e.
-RF + FINGER Mode: In this mode you need both card and fingerprint authorizatio
n to obtain access. If card and fingerprint authorization is successful, the correspon
ding card number will be transmitted to the controller. For a user who did not regi
stered one’s fingerprint, RF Only mode is applied automatically.

Product Overviewp.11
1.3 Card Number Input Format
When an external reader is connected, FGR006/IP-FGR006 accepts input data from the exte
rnal reader via 26 Wiegand, ABA Track II, and 4/8bit Burst format. FGR006SR accepts input
data from external reader via 34 Wiegand, ABA TRACK II and 4/8bit Burst format.
1.4 Card Number Output Format
If a fingerprint data is authorized, FGR006/IP-FGR006 transmits the corresponding card nu
mber to the controller via 26/34bit Wiegand or ABA Track II depending on output setting
1.5 *1OK Signal Output (Applicable when output setting is 26/34bit Wiegand, O
pen collector Output)
Transmit OK Signal to notify that fingerprint is used to authorization. In case of authorizatio
n without fingerprint, the FINGER006 does not transmit OK Signal. Transmitting OK signal n
eeds connecting OK Signal wire (Orange) to an input port of the controller.
1.6 Error Signal Output (Applicable when output setting is 26/34bit Wiegand, O
pen collector Output)
Transmit ERROR Signal when any type of authorization is failed. Transmitting ERROR signal
needs connecting OK Signal wire (Orange with black stripe) to an input port of the controlle
r.
What FGR006 Transmits
In case of success In case of failure
(Normal Mode)
In case of failure
(Extension Mode)
Fingerprint Only Card ID,
OK Signal
ERROR Signal ERROR Signal
Fingerprint + RF Card Card ID,
OK Signal
ERROR Signal Card ID,
ERROR Signal
1 * In normal mode, the FGR006 transmits Card ID only when authorization is a success. But if you set
‘Extension mode’ by application software, the FGR006 transmits Card ID also when authorization is fail
ed. In this case, you can get information of users whose authorization is failed. However, because a Ca
rd ID is transmitted to the controller, users who failed authorization of the FGR006 can get access to a
door depending on setting of the controller. (Default is Normal Mode)

p.12Product Explanation
RF Card Only Card ID ERROR Signal Card ID,
ERROR Signal
In case of success In case of failure
(Normal Mode)
In case of failure
(Extension Mode)
*Please refer to p.24 for output mode.
1.7 Dual Finger Mode
Dual Finger Mode is a function that allows a user to register two fingers for one ID so that t
he user can receive authorization with either of the two registered fingers. It can be used wh
en user’s fingers have injured.
2Product Explanation
2.1 Panel Description

Product Overviewp.13
2.2 Color Coded & Wiring Table
Signal Color
Main Power (+12V) Red
Power Ground (GND) Black
Wiegand Data 0 Out / ABA Track II Data Out Green
Wiegand Data 1 Out / ABA Track II Clock Out White
Error Signal Out / ABA Track II CP Out Orange
OK Signal Out Orange with Black stripe
Tamper Switch Out Purple
Wiegand Data 0 In Pink
Wiegand Data 1 In Cyan
LED Control In Blue with White stripe
Buzzer Control In White with Red stripe
RS422 (TX+) Gray
RS422 (TX-) Yellow
RS422 (RX+) Brown
RS422 (RX-) Blue
*RS485 communication, you should combine Gray (TX+) wire and Brown (RX+) wi
re, Yellow (TX-) wire and Blue (RX-) wire and then connect the two combined wire
s to a converter. We recommend you to use an INC300 converter.

Installation Tips & Check Points 7
p.14
1Recommended Cable Type and Permissible Length of
Cable
DESCRIPTION CABLE SPECIFICATION MAXIMUM DISTANCE
Reader (Power and Data)
Reader <--> ACU
Belden #9512, 22 AWG
4 conductor, shielded
150m
Belden #9514, 22 AWG
8 conductor, shielded
* Should use a wire that is thicker than a wire which can handle maximum current
of the reader.
2Reader Connection
Long distance between the product and ACU(Access Control Unit) may cause voltage drop.
For example, if you install a reader that consumes 100mA current 100m away from ACU an
d supply power to the reader from the ACU, the voltage drop is 1V. In this case, ACU cannot

Installation Tips & Check Pointsp.15
recognize the Wiegand data signal from the reader because ACU cannot recognize voltage l
evel which is inputted as “1” or “0”. Following methods below can reduce voltage drop.
 Reduce the DC resistance of wire; using a thick cable or add more wires to the
wire in parallel. If you connect 4 wires in parallel, the DC resistance of the wire will
be reduced to 1/4 of the DC resistance of the single wire.
 Use separate power for the reader; In case of using external power for the reade
r and not supplying power from the ACU, there is no voltage drop.