IDTECK Star RFK505 User manual

User’s Manual
PIN & Proximity Card Reader

2
Table of Contents
1. Important Safety Instructions ............................................................................................4
2. General.................................................................................................................................4
3. Features ...............................................................................................................................5
4. Specification........................................................................................................................6
5. Identifying Supplied Parts..................................................................................................7
6. Product Overview................................................................................................................7
6.1 Functions.........................................................................................................................7
6.2 Product Explanation ........................................................................................................7
6.2.1 Front Panel Description...........................................................................................7
6.2.2 Wire Color Table......................................................................................................8
7. Installation Checkpoint & Tips...........................................................................................9
7.1 Check Point before Installation........................................................................................9
7.1.1 Selection of Cable...................................................................................................9
7.1.2 Recommended Cable Type and Permissible Length Cable ....................................9
7.2 Check Point during Installation ......................................................................................10
7.2.1 Termination Resistors............................................................................................10
7.2.2 How To Connect Termination Resistors.................................................................11
7.2.3 Grounding System for Communication Cable ....................................................... 11
8. Installation .........................................................................................................................12
8.1 Installation of the Product ..............................................................................................12
8.2 System Initialization.......................................................................................................13
8.3 Wiring ............................................................................................................................13
8.3.1 Power....................................................................................................................13
8.3.2 Output Connections ..............................................................................................13
8.4 Wire Connection to Access Controller ...........................................................................14
9. Communication.................................................................................................................14
9.1 RS232 Communiction Port Connection .........................................................................14
9.2 RS422 Communication Port Connection .......................................................................14
9.2.1 RS422 Connection (SINGLE RFK505 CONNECTION).........................................14
9.2.2 RS422 Connection (MULTIPLE RFK505s CONNECTIONS) ................................15
9.3 DIAL UP MODEM..........................................................................................................16
9.4 TCP/IP CONVERTER (EXTERNAL VERSION).............................................................16
10. Basic Settings .................................................................................................................16
10.1 INITIALIZATION OF RFK505 ......................................................................................16

3
10.2 HOW TO ENTER THE SETUP MENU ........................................................................17
11. Operation .........................................................................................................................17
11.1 NORMAL OPERATION................................................................................................17
11.2 DATA OUTPUT FORMAT (SETUP MENU F2).............................................................17
11.2.1 WIEGAND OUTPUT FORMAT............................................................................17
11.2.2 ABA TRACK II MAGSTRIPE OUTPUT FORMAT ................................................18
11.2.3 4/8bit BURST for PIN OUTPUT FORMAT...........................................................19
12. Setting Changes..............................................................................................................20
12.1 SETUP MENU F1........................................................................................................21
12.1.1 TIME SETTING ...................................................................................................21
12.1.2 COMMUNICATION ID (ADDRESS) DISPLAY ....................................................22
12.1.3 BAUD RATE SETTING .......................................................................................22
12.1.4 MASTER ID CHANGE ........................................................................................22
12.1.5 SYSTEM INITIALIZE...........................................................................................23
12.2 SETUP MENU F2........................................................................................................24
12.2.1 LCD DISPLAY SETTING.....................................................................................24
12.2.2 OUTPUT MODE SETTING .................................................................................24
12.2.3 LED_BUZZER_CONTROL .................................................................................25
12.2.4 FUNCTION KEY OUT.........................................................................................25
12.3 SETUP MENU F4........................................................................................................25
12.3.1 VERSION CHECK ..............................................................................................25
12.3.2 LCD TEST...........................................................................................................26
12.3.3 KEYPAD TEST....................................................................................................26
12.3.4 READER TEST ...................................................................................................26
12.3.5 COMMUNICATION TEST ...................................................................................26
13. Troubleshooting ..............................................................................................................27
14. FCC Registration Information ........................................................................................29
15. Warranty and Service......................................................................................................30
16. Template...........................................................................................................................31

4
1. Important Safety Instructions
When using PIN & Proximity Card Reader, basic safety precautions should always be followed to
reduce the risk of fire, electrical shock, and injury to persons.
In addition, the following safety guides should also be followed:
1. Fully read and understand all instructions and follow them completely.
2. Follow all warnings and instructions marked on the product.
3. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use mild soap.
4. Do not use this product near water.
5. Only operate this product using the type of power source indicated. If you are not sure of the type
of power supplied to your installation site, consult your dealer of local power company.
6. Never insert objects of any kind into the product or through the cabinet slots as they may touch
voltage points and/or short circuit parts possibly resulting in fire or electric shock.
Never spill liquid of any kind on the product.
7. Never disassemble this product by yourself; take the unit to a qualified service center whenever
service or repair is required. Opening or removing the covers may expose you to dangerous
voltages or other risks. Also, incorrect reassembly can cause electric shock when the unit is
subsequently used.
8. Unplug this product from the Direct Current (DC) power source and refer to qualified service
personnel under these conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled on the product.
c. If the product does not operate normally after following the operating instructions in this
manual. Adjust only those controls that are covered by the operating instructions in this
manual. Improper adjustment of other controls that are not covered by this manual may
damage the unit and will often require extensive work by a qualified technician to restore
normal operation.
d. If the product exhibits a distinct change in performance.
2. General
The Star RFK505 / iPASS IPK505 / IDTECK SRK505U is an elegant looking and built in an
attractive 10cm (4”) read range PIN & Proximity Card Reader with keypad and LCD display.
The RFK505 displays current time on the LCD and has back lighting on the keypad that ensures you
successful operation. The RFK505 allows you to access door with proximity card and personal PIN
numbers. Three LEDs of green, yellow and red, inside Piezo buzzer sound and LCD will guarantee
you an accurate and reliable system operations. When power is supplied to the RFK505, red LED
indicator is on. When card data is transmitted, green LED indicator flickers. In addition, yellow LED
indicator flickers when master password is error.

5
3. Features
- 125KHz Proximity / PIN Reader
- PSK Modulation
- Read Range: Up to 4inch (10cm)
- User format available
- Network Communication via RS232 / RS422 / RS485 (Max.256ch)
TCP/IP (External LAN Converter required)
- 26bit Wiegand, ABA Track II and 4/8bit Burst for PIN Output Format selectable
- 16 Numeric Keypads with Back Lighting
- Current Time Display on the LCD
- Dual Tamper Switches
- Wall Mount (US, EU, Asian Gang Box Size)
- Reverse Polarity Protection
- Options: Supervisory Signal
- Compatible Controller:
(26bit Wiegand) iCON100, iTDC, Third Party Controller, Standalone Controller
(34bit Wiegand) iCON100SR, iTDC-SR, Third Party Controller, Standalone Controller
* Comparison Table
RFK505 Built-in 125KHz (4”) Proximity Reader
IPK505 ASK[EM] Format
Built-in 125KHz (4”) Proximity Reader
Built-in 13.56MHz (4”) Contactless Smart Card Reader
SRK505U ISO14443 Type A/B Compatible
Serial Number Read Only

6
4. Specification
Model RFK505
RFK505 IDK50 / IMC125: Up to 2 inch (5cm)
IDC80 / IDC170: Up to 4 inch (10cm)
IPK505 IPK50: Up to 2 inch (5cm)
IPC80 / IPC170: Up to 4 inch (10cm)
Read Range
SRK505U ISK50 / IHC80 / IMC135: Up to 2 inch (5cm)
SDC80: Up to 4 inch (10cm)
Reading Time (Card) 30ms
Power / Current DC 12V / Max.300mA
Communication RS232 / RS422 / RS485 (Max.256ch),
TCP/IP (External LAN Converter required)
Baud Rate 9,600bps (default) / 4,800bps, 19,200bps
and 38,400bps (selectable)
RFK505 / IPK505 26bit Wiegand, ABA Track II,
4/8bit Burst for PIN (selectable)
Output Format
SRK505U 34bit Wiegand, ABA Track II,
4/8bit Burst for PIN (selectable)
LCD Character LCD (2Linges x 16Char) /
2.62” x 0.55” (65.6mm x 13.8mm) Screen
Keypad 16 Key Numeric Keypad with Back Lighting
LED Indicator 3 Array LED Indicators (Red, Green and Yellow)
Beeper Piezo Buzzer
LCD 0°to +50°C (+32°to +122°F)
Operating Temperature RF Reader -35°to +65°C ( -31°F to +149°F )
Operating Humidity 10% to 90% relative humidity non-condensing
Color / Material Dark Pearl Gray / Polycarbonate
Dimension (W x H x T) 161.5mm x 134mm x 48.5mm
(6.36” x 5.28” x 1.9”)
Weight 547g (1.21lbs)

7
5. Identifying Supplied Parts
Please unpack and check the contents of the box.
(Optional accessories, if purchased, may be included in the package)
Main Unit Wall Mount O-ring User’s Manual
( 1ea ) ( 1ea ) ( 5ea ) ( 1copy)
6. Product Overview
6.1
6.2
6.2.1
Functions
Current Time Display on the LCD
The Star RFK505 / iPASS IPK505 / IDTEKC SRK505U displays card reading status, card
number and current time on the LCD.Setting Changes
The Star RFK505 / iPASS IPK505 / IDTEKC SRK505U manages output mode setting,
external buzzer control and external LED control.
Keypad
If the Star RFK505 / iPASS IPK505 / IDTEKC SRK505U is not connected to a host PC,
the integrated keypad and LCD display module can also be used for the entire programming
process.
Product Explanation
Front Panel Description
10 Numeric Keypad
Card Reading
Status LED
LCD Display
System Operation
Status LED
Function Keypad
Figure:Star RFK505 / iPASS IPK505 / IDTEKC SRK505U Front Description

8
LCD Module:
LCD module display Star RFK505 / iPASS IPK505 / IDTEKC SRK505U status.
System Operation Status LED:
When the power is applied to the unit, the red LED is turned on.
During the reader transmits card data to the controller, the green LED is turned on and
card reading status LED is flickers once changing the green color at the same time.
16 key pad:
You can operate the unit manually by using the key pad.
Function key:
The unit has four Function keys ([F1], [F2], [F3], [F4]).
Card reading status LED:
When a card is read, the card reading status LED turns on green.
6.2.2 Wire Color Table
SIGNAL COLOR
Main Power (+12V) Red
Power Ground (GND) Black
ABA Track II CP Out Orange
Wiegand Data 0 Out /
ABA Track II Data Out Green
Wiegand Data 1 Out /
ABA Track II Clock Out White
Tamper Switch Out Purple with White stripe
RS232 (TX) Black with White stripe
RS232 (RX) Red with White stripe
RS422 (TX+) Gray
RS422 (TX-) Yellow
RS422 (RX+) Brown
RS422 (RX-) Blue
* Please cut out tail connector before installation.

9
7. Installation Checkpoint & Tips
Installing the Star RFK505 / iPASS IPK505 / IDTEKC SRK505U is an easy task. It can be installed
with common hand tools and readily available communications wires. This section provides
information about wiring, wire runs and other information to make the installation quick and easy.
7.1
7.1.1 S
7.1.2 R
Check Point before Installation
election of Cable
System installation cabling will be configured as follow.
RFK505 RFK505
Figure: System Installation Layout
ecommended Cable Type and Permissible Length Cable
Reference Description Cable Specification Maximum
Distance
①Controller Power (DC12V)
DC Power Controller
Belden #9409, 18 AWG
2 conductor, unshielded 30m
Belden #9512, 22 AWG
4 conductor, shielded
②Reader (Power and Data)
RFK505 Controller Belden #9514, 22 AWG
8 conductor, shielded
150m
③Door Contact
Exit Button
Belden #9512, 22 AWG
4 conductor, shielded 300m

10
Sensor Input
Input Controller
Belden #9514, 22 AWG
8 conductor, shielded
④Door Lock, Alarm Device
Lock (Alarm) Controller
Belden #9409, 18AWG
2 conductor, unshielded 300m
RS232 Cable
⑤Converter Host P.C.
Belden #9829, 24 AWG
2-twisted pair, shielded 15m
RS485 Cable
Controller Converter
Controller Controller
Controller RFK505
RFK505 RFK505
RFK505 Converter
Belden #9829, 24 AWG
2-twisted pair, shielded
RS422 Cable
⑥
Controller Converter
Controller Controller
Controller RFK505
RFK505 RFK505
RFK505 Converter
Belden #9830, 24 AWG
3-twisted pair, shielded
1,200m
* : Need thicker wire if you connect the reader with high current consumption.
7.2
7.2.1 T
Check Point during Installation
ermination Resistors
Termination resistors are used to match impedance of the network to the impedance of the
transmission line being used. When impedance is mismatched, the transmitted signal is
not completely absorbed by the receiver and a portion of signal is reflected back into the
transmission line.
The decision whether or not to use termination resistors should be based on the cable
length and data rate used by the communication system.
For example, if you use 9,600 baud rate and 1,200m length of cable, the propagation
velocity of cable is 0.66 x speed of light (This value is specified by the cable manufacturer),
if we assume the reflections will damp out in three round trip up and down the cable length,
the transmitted signal will stabilize 18.6us after the leading edge of a bit. Since the data bit
is captured in the middle of the bit which is approximately 52us after the leading edge of a
bit. The reflection stabilizing time 18.6us is much before the center of the bit therefore the
termination resistors are not required.
However, if you install the cable to maximum length, the impedance of cable and network
is mismatched and the transmitted signal is overlapped by the reflected signal. In this case,
it is recommended to add termination resistors to the end of the receiver lines. A 120Ω
resistor can be used for termination resistor in parallel between the receiver lines “A” and
“B” for 2 wires RS485 system or “RX+” and “RX-” for 4 wires RS422 system. A termination
resistor of less than 90Ωshould not be used and no more than 2 terminations should be
used in one networking system.

11
7.2.2 H
7.2.3 G
ow To Connect Termination Resistors
Last RFK505
Figure: Termination resistors for 2 wire RS485 communication system
Last RFK505
Figure: Termination resistors for 4 wire RS422 communication system
rounding System for Communication Cable
We recommend to using proper grounding system on the communication cable.
The best method for grounding system is to put the shield wire of the communication cable
to the 1st class earth grounding; however it is not so easy to bring the earth ground to the
communication cable and also the installation cost is raised.
There will be three grounding point where you can find during installation;
1) Earth Ground
2) Chassis Ground
3) Power Ground
The most important point for grounding system is not to connect both ends of shield wires
to the grounding system; in this case there will be a current flow through the shield wire
when the voltage level of both ends of shield wire is not equal and this current flow will
create noise and interfere to communications.
For the good grounding, we recommend to connecting ONLY one end of shield wire of
communication cable to grounding system; If you find earth ground nearby, then connect
one end of shield wire to earth ground; If you do not have earth ground nearby, then find
chassis ground and connect one end of shield wire to chassis ground; If you do not find
both earth ground and chassis ground, then connect one end of shield wire to power
ground. (GND of Star RFK505, iPASS IPK505, IDTECK SRK505U)
Note that if the chassis ground is not properly connected to the earth and floated from the
ground level, then grounding to the chassis ground will give the worst communication; in
this case we recommend to using power ground instead of chassis ground.

12
RFK505 #1 RFK505 #2 RFK505 #3 RFK505 #N
Figure : Grounding system
8. Installation
8.1 Installation of the Product
8.1.1. Use the provided template to drill two 6-32 holes and one 1/2" hole on the proper location
of the wall to mount the Wall Mount bracket as shown below.
(Skip this step if the gang box is already installed on the wall.)
8.2.2 Using 2 screws, install wall mount to the wall.

13
※CAUTION
Before mounting the main unit to the Wall Mount bracket, operational test of the unit should be
completed, as the locking pins will lock the unit to the Wall Mount. Removing the unit from the
Wall Mount bracket after they have been installed together may cause damages to the
bracket and render its effectiveness.
8.2.3 Insert 5 O-rings to the wall mount as indicated, then route the cable of the main unit through
the center hole and push the main unit to wall mount to lock the main unit and make sure
that the main unit is locked with wall mount.
8.2 System Initialization
The Hardware initialization must be operated before the RFK505 installation.
First, turn off the system power and connect 3 wires (pink, cyan and black (GND)), and turn
on the system power. Then, “Initialize beep” will be heard and picture will be displayed.①
○
1
System Initialize
1 – Yes, 0 - No
○
2
○
4
System is Clear
Remove Wires!!
○
3
System
Initializing...
[ _ _ _ _ ]
Master Password
1. : For Hardware initializing, enter key①<1>.
2. ②: Enter initial master password(<3141>).
3. ③: Showing initializing.
4. ④: After initializing – Turn main power OFF and separate 3 wires and
turn main power ON again.
8
8.3
8.3.2
.3 Wiring
.1 Power
- Connect the (+) wire of DC 12V power to the +12V (Red wire).
- Connect the GND (-) wire of DC 12V power to the GND (Black wire).
Output Connections
Wiegand Data Connection
- Connect Data 0 of the controller to Wiegand Data 0 Out (Green wire).
- Connect Data 1 of the controller to Wiegand Data 1 Out (White wire).
- If you disconnect power from the controller, connect the GND port between controllers.
ABA Track II Connection
- Connect Data 0 of the controller to ABA Track II Data Out (Green wire).
- Connect Data 1 of the controller to ABA Track II Clock Out (White wire).

14
- Connect CP of the controller to ABA Track II CP Out (Orange wire).
- If you disconnect power from the controller, connect the GND port between controllers.
8.4 Wire Connection to Access Controller
Access Controller
Main Power (+12V)
Power Ground (GND)
ABA Track II CP Out
Wiegand Data 0 Out /
ABA Track II Data Out
Wiegand Data1 Out /
ABA Track II Clock Out
Tamper Switch Out
RS232 (TX)
RS232 (RX)
RS422 (TX+)
RS422 (TX-)
RS422 (RX+)
RS422 (RX-)
Red
Black
Orange
Green
White
Purple with White stripe
Black with White stripe
Red with White stripe
Gray
Yellow
Brown
Blue
9. Communication
9.1
9.2
9.2.1
RS232 Communiction Port Connection
A 9-pin connector (Serial communication connector, female) is required to connect
the RFK505 to a host computer via RS232 communication Please follow the instructions.
- Connect RS232-TX port of RFK505 to the pin 2 of the 9-pin connector.
- Connect RS232-RX port of RFK505 to the pin 3 of the 9-pin connector.
- Connect RS232-GND of RFK505 to the pin 5 of the 9-pin connector.
Plug in the 9-pin connector to COM1 or COM2 Port of the host PC.
Install and run RFK505 Application Software.
RS422 Communication Port Connection
RS422 Connection (SINGLE RFK505 CONNECTION)
RS422/RS232 converter (CNP200) is required to use RS422 communication between
the RFK505 and a host computer. Please follow the instructions.
- Connect RS422-TX(+) of the RFK505 to RS422-RX(+) port of the converter.
- Connect RS422-TX(-) of the RFK505 to RS422-RX(-) port of the converter.
- Connect RS422-RX(+) of the RFK505 to RS422-TX(+) port of the converter.
- Connect RS422-RX(-) of the RFK505 to RS422-TX(-) port of the converter.
- Plug in the RS232 9pin connector of the converter to the COM1 or COM2 Port of the PC.
- Install and run RFK505 Application Software.

15
Figure: RS422 Communication between RFK505 and Host PC
9.2.2 RS422 Connection (MULTIPLE RFK505s CONNECTIONS)
RS422/RS232 converter is required to use RS422 communication between multiple
RFK505s and a host computer. Please follow the following instructions.
First, you have to connect all RS422 port of all RFK505s in parallel.
- Connect RS422-TX(+) of one RFK505 to RS422-TX(+) of another RFK505.
- Connect RS422-TX(-) of one RFK505 to RS422-TX(-) of another RFK505.
- Connect RS422-RX(+) of one RFK505 to RS422-RX(+) of another RFK505.
- Connect RS422-RX(-) of one RFK505 to RS422-RX(-) of another RFK505.
Second, you have to connect one of RS422 port of RFK505 to RS422/RS232 converter.
- Connect RS422-TX(+) of the one RFK505 to RX(+) port of the converter.
- Connect RS422-TX(-) of the one RFK505 to RX(-) port of the converter.
- Connect RS422-RX(+) of the one RFK505 to TX(+) port of the converter.
- Connect RS422-RX(-) of the one RFK505 to TX(-) port of the converter.
- Plug in the RS232 9pin connector of the converter to the COM1 or COM2 port
of the PC.
- Install and run RFK505 Application Software.
Figure: RS422 Communication between FINGER006s and the Host PC

16
9
9
.3 DIAL UP MODEM
Please, see the Software manual.
.4 TCP/IP CONVERTER (EXTERNAL VERSION)
Please, see the Software manual.
10. Basic Settings
POWER ON
SYS. INITIALIZE ?
If you turn on the system power
after connected 3 wires (pink, cyan
and black(GND)), you can enter
system initialize mode.
H/W RESET MODE
WAIT INITIIAL MASTER P/W
("3141")
RIGHT ?
SYSTEM INITIALIZE
YES
YES
NO
NO
WAITING REBOOT
INITIAL BEEP( - - - -)
SYSTEM READY
GENERAL BOOT
In the system ready, LCD
display model name,
ID INPUT ?
YES
MASTER ID ?YES
ENTER SETUP MENU
END SETTING ?
YES
NO
SETTINGIN SETUP MODE
INITIALIZE BEEP( - - -)
NO
OUTPUT CONTROL OF EACH
STATUS
10.1 INITIALIZATION OF RFK505
Before installation of the system and when it is not able to enter the setup menu (system
error or something wrong), the user has to Hardware initialize.
The user has to initialize H/W using an external reader port.
Turn off the system power and connect 3 wires (pink, cyan and black (GND)), and turn on
the system power. (Ref. 8.2 SYSTEM INITIALIZATION). Initializing will erase all stored data
incl. registered IDs data. Then, the user has to do setting the system parameter. Before the
first installation, the user must Hardware initialize.

17
Remove Wires!!
System is Clear System Initialize
1 – Yes, 0 - No
Master Password
[3141]
10.2 HOW TO ENTER THE SETUP MENU
To setup or to change the RFK505 settings, the user has to enter the SETUP MENU
first. To do so, press the 8 times <0> key for Master ID (Default setting “00000000”) and
<ENT> key and press Master Password (Default setting “3141”) and the user can get into
SETUP MENU. There are 3 main SETUP MENUs and the user first gets into [SETUP
MENU F1]. The user can move to other SETUP MENU by pressing <F1> key for [SETUP
MENU F1], <F2> key for [SETUP MENU F2], and <F4> key for [SETUP MENU F4].
There are several SUB MENUs in the main SETUP MENU and the user can scroll up and
down the SUB MENU by pressing <4> and <6> key
in the main SETUP MENU. If the user pressed <ESC> key, RFK505 will be out of the
SETUP MENU and returned to normal operation. The user can also change the Master ID
in the [SETUP MENU F1]. The Master ID for SRK505U is 10 times <0> key (Default
setting “0000000000” ), and default Master Password is <3141>.
11. Operation
11.1
11.2 D
11.2.1 WIE
NORMAL OPERATION
In usual power on, the main lights on two red LED indicators of operating system status and
card reading status. If you present RF card to the reader, red LED indicator of card reading
status is changed to green color. Then the reader transmits card data to the controller and
turns on red LED indicator again to wait for next card data reading.
ATA OUTPUT FORMAT (SETUP MENU F2)
GAND OUTPUT FORMAT
1. Data format ( * : SRK505U)
Bit 1 : Even parity of bit 2 ~ bit 13
Bit2∼9 : Facility code (000 ~ 255)
Bit10∼25 : ID number (00000 ~ 65,535)
* Bit 2 ~ 33 : ID number (0000000001 to 4294967295)
Bit26 :Oddparity
*Bit34 :Oddparity

18
2. Timing diagram
3.5V
0.5V
40uS
2mS
Data 0 40uS
40uS
0.5V
3.5V
Data 1
5V
5V
0V
0V
11.2.2 ABA TRACK II MAGSTRIPE OUTPUT FORMAT
1. Data format (for Card numbers)
Zero bit
ID number
(00000~65535)
LRC
Facility Code
(1248P (00000~00255))
low bit first, odd parity last
Start Character
(11010 Hex ‘B’)
Zero bit (10bit)
2. Data format (for PIN)
Start Character
(11010 Hex ‘B’)
PIN (1char to 8char)
low bit first, odd parity last
LRC Zero bit
Zero bit (10bit)

19
3. Timing diagram
CLK
(RD1)
Data
(RD0)
1240us
940us
6000us
CP
1544us
6000us
11.2.3 4/8bit BURST for PIN OUTPUT FORMAT
1. Data format
(4bit Burst output format)
Keypads Binary Hexa Keypads Binary Hexa
0 0000 0 6 0110 6
1 0001 1 7 0111 7
2 0010 2 8 1000 8
3 0011 3 9 1001 9
4 0100 4 ESC 1010 A
5 0101 5 ENT 1011 B
(8bit Burst output format)
Keypads Binary Hexa Keypads Binary Hexa
0 11110000 F0 6 10010110 96
1 11100001 E1 7 10000111 87
2 11010010 D2 8 01111000 78
3 11000011 C3 9 01101001 69
4 10110100 B4 ESC 01011010 5A
5 10100101 A5 ENT 01001011 4B
( Function key output format)
Keypads Binary Hexa Keypads Binary Hexa
F1 00111100 3C F3 00011110 1E
F2 00101101 2D F4 00001111 0F

20
2. Timing diagram
3.5V
0.5V
40uS
2mS
Data 0 40uS
40uS
3.5V
0.5V
Data 1
5V
0V
5V
0V
12. Setting Changes
INITIAL DISPLAY
(MODEL NAME, CURRENT TIME)
ID INPUT?
MASTER ID
/PW/FINGERPRINT ?
YES
YES
NO
OPERATE GENERAL
MODE
SETUP MODE
NO
SETUP F1 MODE SETUP F2 MODE SETUP F3 MODE SETUP F4 MODE
1. TIME SETTING
2. COMM ID SETTING
3. BAUD RATE
4. MASTER ID CHANGE
5. SYS INITIALIZE
1. LCD DISPLAY
2. OUTPUT MODE
3. LED/BUZZER_CON
4. FUNC KEY OUT
1. F/W VERSION
2. LCD TEST
3. KEYPAD TEST
4. READER TEST
5. COMM TEST
.☞To setup or to change the RFK505 / IPK505 settings, the user has to enter the SETUP MENU first.
To do so, input Master ID (Default setting “00000000”), input Master Password(Default setting
“3141”) and the user can get into SETUP MENU. There are 4 main SETUP MENUs and the user
first gets into [SETUP MENU F1]. The user can move to other SETUP MENU by pressing <F1> key
for [SETUP MENU F1], <F2> key for [SETUP MENU F2], <F3> key for [SETUP MENU F3], and
<F4> key for [SETUP MENU F4]. There are several SUB MENUs in the main SETUP MENU and