Impex MARCY BF-1201 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
BF-1201
Retain This
Manual for
Reference
100714
OWNER'S
MANUAL
MARCY®
Deluxe Elliptical Machine
BF-1201
IMPEX®INC.
2801 S. Towne Ave., Pomona, CA 91766
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................…. 1
IMPORTANT SAFETY NOTICES..................................................................…. 2
HARDWARE PACK……….....…....................................................................…. 4
ASSEMBLY INSTRUCTIONS........................................................................…. 5
EXPLODED DIAGRAM………………………………………………………………. 15
PARTS LIST...................................................................................................… 17
OPERATION…………………………………………………………………………. 18
WARRANTY.................................................................................................…. 19
ORDERING PARTS.....................................................................................….. 19
BEFORE YOU BEGIN
Thank you for selecting the MARCY Deluxe Elliptical Machine BF-1201 by IMPEX®
INC. For your safety and benefit, read this manual carefully before using the machine.
As a manufacturer, we are committed to provide you complete customer satisfaction.
If you have any questions, or find there are missing or damaged parts, we guarantee
you complete satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number. Our
Customer Service Agents will provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm
up.
11. Never operate the machine if the machine is not functioning properly.
12. The Maximum Weight Capacity is 300 lbs.
13. Read all warnings posted on the exercise bike.
14. Inspect the exercise bike for worn or loose component prior to use. Tighten/replace any
loose or wore components prior to use.
15. Care should be taken in mounting or dismounting the machine.
16. This exercise bike is for consumer and home use only.
Maintenance and Storage
1. Inspect and tighten all parts each time you use the machine. Replace any worn parts immediately.
2. The bike can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
3. Store the machine IN-DOOR. Excess moisture and water would cause rust on the frame.
4. The machine shall be placed at least 24 inches away from the wall or/and any other object such as
furniture to provide safe access to and passage around the machine.
5. To avoid possible injury, the help of two or more people are needed when moving the machine around.
6. Periodically lubricate all moving parts with the Grease supplied by manufacturer, WD-40, or light oil.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABELS PLACEMENT
The Warning Labels shown here have been placed on the Rear Stabilizer, Front Post, and Main Frame. If the
labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the
labels in location shown.
3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the
size.

4
ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: One Crossing Wrench and Allen Wrench, provided
by manufacturer.
NOTE: It is strongly recommended that two or more people assemble this machine to avoid
possible injury.
STEP 1 (See Diagram1)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Attach the Front Stabilizer (#39) to the Main Frame (#32). Secure it with two M8 x 2 ½” Carriage Bolts
(#35), two 5/8” Curved Washers (#24), and two M8 Acorn Nuts (#37).
C.) Attach the Rear Stabilizer (#36) to the Main Frame. Secure it with two M8 x 2 ½” Carriage Bolts (#35),
two 5/8” Curved Washers (#24), and two M8 Acorn Nuts (#37).
D.) Securely tighten all Nuts and Bolts installed. DIAGRAM 1

5
STEP 2 (See Diagram 2)
A.) Note: Extra help may be needed to hold the Front Post (#42) while connecting the computer
wires.
B.) Connect the Upper Computer Wire (#91) from the bottom of Front Post to the Lower Computer
Wire (#92) from the main Fame (#32).
C.) Attach the Front Post to Main Frame. Secure them together with four M8 x ¾” Allen Bolts (#21),
four Ø 5/8” Lock Washers (#7), and four Ø 5/8” Curved Washers (#24).
DIAGRAM 2

6

STEP 3 (See Diagram 3)
A.) Note: In order to install the Pedal Supports (#30 & #38), extra help may be needed.
B.) Do not tighten Nuts and Bolts until instructed to do so.
C.)Attach the Left Pedal Support (#38) onto the groove on left Roller Wheel (#49).
D.)Insert the pivot on Left Pedal Support into the hole on the left Connecting Bracket (#54).
Secure it with one M8 x ¾” Allen Bolt (#21) and one Ø 1 ¼” Large Black Washer (#31).
E.) Attach the Left Connecting Rod (#41) onto the bracket on Left Pedal Support.Secure the Left
Connecting Rod to the Left Pedal Support with one 3 ¼” Axle (#19), one Ø 5/8” Flat Washer
(#22), and one M8 Aircraft Nut (#23).
F.) Repeat C to E to install the Right Connecting Rod (#15) and Right Pedal Support (#30).
G.)Securely tighten all Nuts and Bolts installed. DIAGRAM 3
7

STEP 4 (See Diagram 4)
A.) Cover the heads of the two M8 x ¾” Hex Bolts (#6) pre-installed by factory with two M8
Nut Caps (#5).
B.) Cover the two M8 Aircraft Nuts (#23) installed in Step-3 with two M8 Nut Caps (#5).
DIAGRAM 4
8

STEP 5 (See Diagram 5)
A.) Attach the two Pedals (#29) onto the Left & Right Pedal Support (#38 & #30). Secure each
Pedal with three M8 x 1” Allen Bolts (#28).
DIAGRAM 5
9

STEP 6 (see Diagram 6)
A.) Insert the Right Stride Handle (#2) into the Right Connecting Rod (#15). Insert the Left
Stride Handle (#44) into the Right Connecting Rod (#41).
B.) Securely tighten each Handle with two M8 x 2” Carriage Bolts (#11), two Ø 5/8” Curved
Washers (#24), two Ø 5/8” Lock Washers (#7), and two M8 Acorn Nuts (#37).
DIAGRAM 6
10

STEP 7 (See Diagram 7)
A.) Attach the Water Bottle Rack (#18) to the Front Post (#42). Secure it with two M5 x 5/8”
Philips Screws (#17).
B.) Store the Water Bottle (#14) in the Rack.
DIAGRAM 7
11

STEP 8 (See Diagram 8)
A.) Attach the Stationary Handle (#27) to Front Post (#42). Secure it with four M8 x ¾” Allen
Bolts (#21), four Ø 5/8” Lock Washers (#7), and four Ø 5/8” Flat Washers (#22).
DIAGRAM 8
12

STEP 9 (See Diagram 9)
A.) Remove the four M5 x 5/8” Computer Philips Screws (#43) from the Computer (#45).
B.) Connect the Upper Computer Wire (#91) to the wire on Computer.
C.)Plug the sensor wire (#93) on the Front Post (#42) into the Computer.
D.)Attach the Computer to the bracket on Front Post. Secure it with the four (removed
previously) M5 x 5/8” Computer Philips Screws (#43).
DIAGRAM 9
13

STEP 10 (See Diagram 10)
A.) Plug the AC Adapter (#34) to110v outlet, and plug the power cord into the Main Frame
(#32). Note: Only use the original AC Adapter from manufacturer. Do not use any
Adapter, which is not from manufacturer.
DIAGRAM 10
14

EXPLDOED DIAGRAM
15

16

PARTS LIST
KEY NO. DESCRIPTION Q’ty
1 Stride Handle Cover Cap 2 51 Ø 1 1/8” x Ø 7/8” Spacer 2
2 Right Stride Handle 1 52 Ø 1 1/8” x ½” Bushing 2
3 Ø 1 ½” Stride Handle Bushing 2 53 Ø 1 1/8” x ¼” Spacer 2
4 Stationary Handle Grip 2 54 Connecting Bracket 2
5 M8 Nut Cap 4 55 Ø 1 1/8” x 5/8” Bushing 2
6 M8 x ¾” Hex Bolt 2 56 Ø ¾” Black Curved Washer3
7 Ø 5/8” Lock Washer 14 57 M12 Hex Nut 4
8 Ø 1 ¼” Large Flat Zinc Washer 2 58 ST4.2 x 1” Philips Self-tapping Screw 3
9 Plastic Ring 2 59 M25 Nut Cap 2
10 Ø 1 ¼” x Ø ¾” Bushing 1 60 Side Fly Wheel 2
11 M8 x 2” Carriage Bolt 4 61 Fly Wheel Mounting Frame 2
12 Ø ¾” Curved Washer 2 62 ST4.2 x 5/8” Philips Screw 8
13 Ø 1 ¼” x 2 7/8” Upper Bushing 2 63 STE4.2 x 1” Philips Screw 6
14 Water Bottle 1 64 Right Shroud 1
15 Right Connecting Rod 1 65 Belt 1
16 Ø 1 ¼” x Ø ½” Bushing 4 66 Middle Fly Wheel 1
17 M5 x 5/8” Philips Screw 5 67 Ø ¾” Black Lock Washer 2
18 Water Bottle Rack 1 68 600ZZ Ball Bearing 2
19 3 ¼” Axle 2 69 Power Cord 1
20 Ø 1 ¾” Con-shaped End Cap 4 70 Left Shroud 1
21 M8 x ¾” Allen Bolt 13 71 Magnet 1
22 Ø 5/8” Flat Washer 6 72 Motor 1
23 M8 Aircraft Nut 5 73 Sensor Wire 1
24 Ø 5/8” Curved Washer 12 74 ST4.2 x ¾” Self-tapping Screw 2
25 Ø 1” End Cap 2 75 Sensor Base 1
26 Pulse Sensor 2 76 M8 x 3 1/8” Bolt 1
27 Stationary Handle 1 77 M8 Hex Nut 2
28 M8 x 1” Allen Bolt 6 78 M8 x 1 5/8” Allen Bolt 1
29 Pedal 2 79 608ZZ Ball Bearing 2
30 Right Pedal Support 1 80 Ø 1 1/8” x ¼” Sleeve 1
31 Ø 1 ¼” Large Black Washer 2 81 Ø ½” x 5/8” Spacer 1
32 Main Frame 1 82 Ø ½” x 1/8” Spacer 1
33 Rear Stabilizer 2 83 Wheel Bracket 1
34 AC Adapter 1 84 M10 Flange Nut 2
35 M8 x 2 ½” Carriage Bolt 4 85 M6 Bolt 2
36 Rear Stabilizer 1 86 U-shaped Bracket 2
37 M8 Acorn Nut 8 87 Ø ½” Lock Washer 2
38 Left Pedal Support 1 88 M6 Hex Nut 2
39 Front Stabilizer 1 89 Tension Cable 1
40 Front Stabilizer Roller Cap 2 90 Magnetic Controlled Wheel 1
41 Left Connecting Rod 1 91 Upper Computer Wire 1
42 Front Post 1 92 Lower Computer Wire 1
43 M5 x 5/8” Computer Philips Screw 4 93 Pulse Sensor Wire 1
44 Left Stride Handle 1 94 Crossing Wrench (Tool) 1
45 Computer 1 95 #6 Allen Wrench (Tool) 1
46 Handle Foam Grip 2 96 M5 x 3/8” Philips Screw 2
47 Ø 7/8” Large Black Washer 2 97 Ø 3/8” End Cap 1
48 Ø 1” x 5/8” Wheel Bushing 4 98 Wire Sleeve 1
49 Roller Wheel 2 99 Ø 7/8” Curved Washer 2
50 Crank 2
17