Ingenico group AXIUM DX8000-BASE-W2 User manual

WWW.ingenico.com
28-32,boulevard de Grenelle, 75015 Paris - France/ (T)[phone] / (F)[phone]
Ingenico-SA au capital de 47 656 332 / 317 218 758 RCS Nanterre
1
Model: AXIUM DX8000-BASE-W2
User Guide

2
Contents
1. Product Introduction ......................................................................................................................................... 3
1.1 Open Package Inspection............................................................................................................................ 3
1.2 Device Introduction..................................................................................................................................... 3
1.3 Interface definition...................................................................................................................................... 3
2. Product Technology Features ........................................................................................................................... 4
2.1 Product Technology Specifications ............................................................................................................ 4
2.2 Environmental Conditions .......................................................................................................................... 5
2.3 Product Functions....................................................................................................................................... 5
3. WiFi connection ................................................................................................................................................. 6
3.1 Connect DX8000 to the base WiFi.............................................................................................................. 6
3.2 Web Setting of base.................................................................................................................................... 6
3.3 Restore factory Setting .............................................................................................................................. 9
4. Pairing connection............................................................................................................................................. 9
4.1 Prepare for Base Pairing ............................................................................................................................. 9
4.2 Pair method............................................................................................................................................... 10
4.3 Unpair method.......................................................................................................................................... 10
4.4 Ethernet Parameter Setting......................................................................................................................11
4.5 WLAN Parameter Setting..........................................................................................................................11
4.6 Advanced Setting ..................................................................................................................................... 12
4.7 Management Setting................................................................................................................................ 12
5. Fixing of the base............................................................................................................................................. 13
6. FAQs ................................................................................................................................................................. 15
7. Notes ................................................................................................................................................................ 16
8. Delivery and Storage....................................................................................................................................... 16
9. Power Adapter ................................................................................................................................................ 16
10. Standard ............................................................................................................................................................ 17

3
1. Product Introduction
1.1 Open Package Inspection
Open the package to check if there are any disabling masks or transportation damage in the terminals
and fittings.
Procedures：
1) Open the package
2) Check the following items(Subject to actual product configuration)
Base host
Product instruction
12V/3.33A power adapter
AC power cable
3) Save the transportation package and packing material for second use.
1.2 Device Introduction
1. RJ45 Network Interface 2. USB-TYPE A 3. USB-TYPE A
4. USB-TYPE B 5. Reset Button 6. DC12v JACK Power Interface
7. Network LED link & active 8. Two color Indicator lights 9. Pairing Button
10. DX8000 Charging Contact
1.3 Interface definition
1）RJ45 interface

4
2）USB-TYPE A interface
3）USB-TYPE B interface
2. Product Technology Features
2.1 Product Technology Specifications
Sequence
RJ45 Signal
1
ETH_TX+
2
ETH_TX-
3
ETH_RX+
4
NC
5
NC
6
ETH_RX-
7
NC
8
NC
Sequence
USB-TYPE A Signal
1
VBUS 5.0V
2
D-
3
D+
4
GND
Sequence
USB-TYPE B Signal
1
Not connect
2
D-
3
D+
4
GND

5
Port
a DC12V JACK port
a RJ45 network port
two USB A HOST port supporting USB2.0
a USB B DEVICE port supporting USB2.0
Power
Every USB HOST output: 5.0VDC 0.5A
Charge output: 5.0VDC 2.0A
Power adapter: input 100-240V AC, 50/60Hz; output 12V DC 3.33A
Size and Weight
Size：193.8mmx89mmx38.6mm
Net Weight：0.20kg
Gross Weight：0.70kg
2.2 Environmental Conditions
Environmental conditions for running, storing and delivering the product：
Temperature
Running
0℃～40℃
Storage and Delivery
-20℃～70℃
Humidity
Running
10％～90％
Storage and Delivery
5％～90％（40℃）
Atmospheric pressure
86kPa～106 k Pa; Below 2000 meters above sea
level
2.3 Product Functions
The base has three main functions as below:
DX8000 charging：Connect the base with the power adapter, then place DX8000 on the base to get
charged.
Serves as extended communication ports of DX8000: Network port, USB port, etc.
Typical applications: Enables DX8000 to communicate with host computer via USB port, and get
Ethernet through Network port.

6
3. WiFi connection
3.1 Connect DX8000 to the base WiFi
Power on the base.
Check the SSID and password from the label on the back of base.
Click “Settings” menu on DX8000,and then click “Network and Internet”, enter “ Wi-Fi” and select
the base SSID to connect.(step 1~4)
After that , DX8000 can use the RJ45 network of the base.
Step1 Step2 Step3 Step4
3.2 Web Setting of base
The base can be set from the web.
Use a computer to connect the base via WiFi.
The web setting IP of base is 192.168.47.1. Login name is Admin. Password is DX8000BASE.
User can get the status of base on the status page.

7
User can get and change the Ethernet parameter on the Network page.
User can get and change the WLAN parameter on the WLAN page.

8
User can change the operating mode, enable DMZ or set static DHCP on the Advanced page.
User can update the firmware of base, save and reload the settings, change the password on the
Manage page.

9
3.3 Restore factory Setting
Use sharp to click the RESET button to restore the factory setting of the base.
The position of RESET button is below.
4. Pairing connection
If DX8000 want to use the USB ports on the base, it should be paired to the base.
4.1 Prepare for Base Pairing
Only one DX8000 can use the USB ports of the base at the same time.
If the red indicator light is on, it indicates the base is available for pairing.
If the green indicator light is on, it indicates the base is successfully paired. If the base is to be
paired with another DX8000, long press on the [Pairing] button to clear the pairing record . When
the red indicator light is on, pair another DX8000 with the base.

10
Illumination of two color indicator lights：
SN
Light Condition
Base Status
1
Red light on
Base to be paired
2
Green light flashing
Base paired but disconnected with DX8000
3
Green light on
Base paired and connected with DX8000
4
Red light flashing
Base in upgrading
4.2 Pair method
First,connect DX8000 to the base via chapter 3.1.
Click “Settings” menu on DX8000,and then click “Base”,input the web password [Step1].
Click the grey button beside the SSID “ING2.4G_XXXXXXX” to pair [Step2].
After pairing,we can check the ports of base in the menu.[Step3].
Step1 Step2 Step3
4.3 Unpair method
Only the paired DX8000 could be unpaired with the base. When DX8000 unpairs the base, the base
will change its conditions to “unpaired” with the red light on.
Click the blue button besides the SSID [Step1]. Click “YES” [Step2] to unpair the base with DX8000: