Insignia KY002 Series User manual

www.insigniashowers.com Last Modied: 03/10/2023
INSTALLATION MANUAL
KY002 Infrared
Sauna Series
30 Day Technical Support:
Call 01908 317512 and request technical support for aiding your
installaon.
Replacements Parts: Inside of your warranty period visit:
hps://www.insigniashowers.com, click support and make a
warranty claim.
Spares/Replacements Parts: Outside of your warranty period visit
hps://www.insigniashowers.com/replacement-parts.html
ATTENTION INSTALLERS:
These instrucons must be
le with the customer CHECK ALL CONTENTS BEFORE BUILD COMMENCES. NO RETURNS CAN BE MADE
ONCE THE BUILD HAS STARTED AS IT IS DEEMED ACCEPTANCE OF PRODUCT!

www.insigniashowers.com Last Modied: 03/10/2023
02
Contents
Thank you for your purchase 3
Electrical & Tool requirements 4
Box contents 5
Screw Pack Contents 6
Back and Le Panel Install 7
Right Panel Install 8
Bench Heater Install 9
Bench Install 10
Bench Seat Install 11
Back Rests Install 12
Glass Panels Install 14
Corner Post Install 15
Roof Install 16
Door Install 17
Door Handle Install 18
Roof Cover Install 19
Electrical Connecons 20
Sauna Control Panel Instrucons 21
Remote Control Instrucons 22
Sauna Room Safety Guide 23
WEEE Compliance Statement 24

www.insigniashowers.com Last Modied: 03/10/2023
03
Thank you for your recent purchase of an Insignia Sauna. Please read this booklet with
great care to ensure you get the best out of your build and have a Sauna that will last
for many years to come! Like everything, in order to obtain a rst class product that
will serve you well for many years, the eort and correctness put into the assembly
will reect in the quality of your nish.

www.insigniashowers.com Last Modied: 03/10/2023
04
•Scissors
•Knife
•Spirit Level
•Tape Measure
•Philips Screwdriver
•Electric Drill
•Safety Gloves
•Safety Glasses
Tools Required
Voltage Rang 220-240AC
Frequency Rang 50Hz
Power Rang 1887 Was Sauna
Total Amperage 7.8 amps
Indoor saunas with power consumpon under 3KW have been designed for easy installaon,
allowing for a simple plug-in directly into a standard household power circuit.
Installaon Notes:
1. (Recommended) Consult with a qualied Electrician before connecon to assess
suitability.
2. Ensure all parts are connected safely and correctly.
Always use protection against electrical surges by means of an RCD unit.
If you are uncertain about the installaon process or have any quesons, please feel
free to reach out to our friendly technical support for general advice. For anything more
specic to the electric installaon, please consult with a cered electrician.
Electrical Requirements Model KY002

www.insigniashowers.com Last Modied: 03/10/2023
05
What’s in the Boxes?
Contents Quanty
Roof
Le Panel
Back Panel
Right Panel
Front Panel Glass Door
Slaed Back Rest
Slaed Side Panel Back Rests
Corner Posts
Floor Insert
1
1
1
1
1
1
2
2
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
VERY IMPORTANT
Have you got everything? If not please contact the Insignia directly on 01908 317 512.
Remember NEVER book your tradesman unl everything has arrived, been checked and is
present. No replacement/missing parts can be obtained free of charge during or aer the
build. Any claims can only be within the mescale permied (48 hours aer delivery) and
always BEFORE build.
Contents Quanty
Door Handle
Bench Front Cover
Bench Top Seat
Bench Frame
Heater
Roof Cover
Glass Panel
Glass Door
Screw Pack
1
1
1
1
1
1
2
1
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]

www.insigniashowers.com Last Modied: 03/10/2023
06
Screw Pack Contents
Contents Quanty
ST 60mm Screws
ST 35mm Screws
ST 18mm Screws
ST 12mm Screws
Rubber pads for Heater
M 45mm Bolts
Wire Fixers
Nuts and Washers
12
16
26
7
4
2
7
2
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
VERY IMPORTANT
Have you got everything? If not please contact the Insignia directly on 01908 317 512.
Remember NEVER book your tradesman unl everything has arrived, been checked and is
present. No replacement/missing parts can be obtained free of charge during or aer the
build. Any claims can only be within the mescale permied (48 hours aer delivery) and
always BEFORE build.

www.insigniashowers.com Last Modied: 03/10/2023
07
Step 1 — Installing the Back and Le Panels
The panel connecon brackets are shown (above). Li
panels and locate the interlocking connecon brackets
and push the panel down to secure into posion. Locate
both panels onto the wooden side of the base.

www.insigniashowers.com Last Modied: 03/10/2023
08
Step 2 — Installing the Right Panel
The panel connecon brackets are shown (above). Li
panels and locate the interlocking connecon brackets
and push the panel down to secure into posion. Locate
both panels onto the wooden side of the base.

www.insigniashowers.com Last Modied: 03/10/2023
09
Step 3 — Installing the Bench Heater
4 x ST18mm Screws
Using the ST 18mm screws found in the screw pack,
connect the bench heater behind the bench frame
as shown in the diagram.

www.insigniashowers.com Last Modied: 03/10/2023
10
Step 4 — Installing the Bench
Once the bench panel is in place, locate the splier in the
screw bag & connect the heater wires as shown in the dia-
gram. The earth wire is secured on the back of the heater via
the pre ed nut & bolt.

www.insigniashowers.com Last Modied: 03/10/2023
11
Step 5 — Installing the Bench Seat
Slot the bench top onto the frame securely.

www.insigniashowers.com Last Modied: 03/10/2023
12
Step 6 — Installing the Back Rests
8 x ST35mm Screws
Install the side rest panel using the ST 35mm screws provided in
the screw pack.

www.insigniashowers.com Last Modied: 03/10/2023
13
Step 7 — Installing the Back Rests — connued
6 x ST35mm Screws
Install the back rest panel using the ST 35mm screws provided
in the screw pack.

www.insigniashowers.com Last Modied: 03/10/2023
14
Step 8 — Installing the Glass Panels
Slot the le and right glass panels into the
grooves as shown in the diagram.

www.insigniashowers.com Last Modied: 03/10/2023
15
Step 9 — Installing the Corner Posts
Slot the corner posts into place to secure the glass.

www.insigniashowers.com Last Modied: 03/10/2023
16
Step 10 — Installing the Roof
8 x ST60mm Screws
Carefully place the roof on top of the sauna and
secure with the ST 60mm screws provided in
the screw pack.

www.insigniashowers.com Last Modied: 03/10/2023
17
Step 11 — Installing the Door 4 x M45mm Screws
4 x Nuts and Washers
Carefully secure the glass door with the hinges onto the corner
post as shown in the diagram using the M 45mm screws and
nuts and washers provided in the screw pack.

www.insigniashowers.com Last Modied: 03/10/2023
18
Step 12 — Installing the Door Handle
2 x M45mm Screws
2 x Nuts and Washers
Connect the front piece and the rst part of the back
piece for the inside of the door, and ghten using the
nuts. Connect the second part of the back piece and
secure using the M 45 screws.

www.insigniashowers.com Last Modied: 03/10/2023
19
Step 13 — Installing the Roof Cover
7 x ST18mm Screws
Carefully place the roof cover on top of the roof and secure in
place using the ST 18mm screws provided in the screw pack.

www.insigniashowers.com Last Modied: 03/10/2023
20
Step 12 — Electrical Connecons
14
15
2
3
13
10911 688
12
5
7
4
1
1. Main Power Supply
2. Group A : Connecons for back and leg heater
3. Group B : Connecons for front and side heater
4. Temperature Detector Wire
5. USB Input
6. Temperature Controller Wire
7. Antenna
8. Speaker Wires
9. Fan Wire
10. Ozone
11. Roof Light
12. CD/MP3 Wire
13. Control Panel Wire
14. AC220V Power Cord
15. Chromatherapy Lighng