Ironwood Glacier LFAS 32 User manual

0920
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
LFAS 32/39
FREESTANDING
ATLAS STAND
BY

PARTS DIAGRAM
Right Panel
Right Panel
07010443
07010442
1 ea.
1 ea.
Front
Spanner 07010480 1 ea.
Top Panel 07010401 1 ea.
Shelf Panel 07010428 5 ea.
A
B
C
E
D
F
LFAS32
LFAS39
Left Panel
Left Panel
07010443
07010442
1 ea.
1 ea.
LFAS32
LFAS39
Back Panel
Back Panel
07010456
07010455
1 ea.
1 ea.
LFAS32
LFAS39

H2 Rafix Cam 909911 16 ea.
H3 Euro Slide H0280 5 sets
H1 Rafix Bolt 909925 16 ea.
H5 Screw 901216 40 ea.
H7 Screw 901220 2 ea.
H6 Pencil Stop H6931 1 ea.
H4 Varianta Screw 988060 40 ea.
HARDWARE

ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

#1
B
A
H3
H3
ARROWS INDICATE SCREW LOCATIONS
Place Right Side (A) and Left Side (B) on a clean, carpeted surface with pre-drilled holes facing
up. Insert 3 Rafix Cams (H2) along top edge in each of sides A & B. Screw in 5 Rafix Bolts (H1)
into each of sides (A & B). Line up 5 outside portions of Slide to each side (A & B) and screw in
using 4 Varianta Screws per slide. (see inset for screw position)
#2
C
H2
Insert 6 Rafix cams (H2) into
Back Panel (C)

Insert 4 Rafix Cams (H2) into
Front Spanner (D).
#3
F
H5
H5
H5
H5 H5
H3
H3
H5
H5
H5
RAW SIDE
(BACK)
EB SIDE
(FRONT)
#4
E
H1
H1
H1
H1
H1
H1
Screw in 6 Rafix Bolts (H1) into Top
Panel (E) as shown.
#5
Attach second half of slides
(H3) to each side of the five
Shelf Panels (F) using 4
Panhead Screws (H5) per
slide as shown.
D
H2

With the aid of another person,
position the Cams of the Back
Panel (C) with the bolts of the Right
Side Panel (A) as shown. Turn the
the cams (H2) to secure.
#6
C
A
ANGLE
CUT
TOP
H2
H2
H2
#7 Position the Cams of the Front
Spanner (D) with the bolts on the
Right Side Panel (A) as shown. Turn
the cams (H2) to secure
D
C
A
H1
H1
#8 With the aid of another person,
position Left Side Panel (B) with
the Cams in Back Panel (C) and
Front Spanner (D) as shown.
Turn Cams to secure.
B
C
D
A

With the aid of another person,
stand unit upright. Position Top
Panel (E) over unit lining up
bolts with Cams. Secure Cams
by turning clockwise
#9
E
C
B
A
D
H2
H2
#10 Slide each of the 5 Shelf
Panels (F) into the unit. E
BA
DF
#11 Attach Pencil Stop (H6) to Top
Panel (E) using 2 Panhead
Screws (H7).
H7
H7
E