Ironwood GLACIER CDHD User manual

CDHD
CDHD39
DOOR UNIT
0920
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
AB
C
L
D
Left Side - CDHD
Left Side - CDHD39
01010341
01010443
1 ea.
1 ea.
F
Right Side - CDHD
Right Side - CDHD39
01010341
01010443
1 ea.
1 ea.
Top 01010301 1 ea. Back - CDHD
Back - CDHD39
01010152
01010252
1 ea.
1 ea.
Left Door - CDHD
Left Door - CDHD39
01010375
01010475
1 ea.
1 ea.
Toeboard 01010172 1 ea. G
Adjustable Shelf 01010124 1 ea.
M
Right Door - CDHD
Right Door - CDHD39
01010375
01010475
1 ea.
1 ea.
E
Bottom 01010111 1 ea.

H2 Leveler H2002 4 ea.
H4 Flush Rafix Cam 909911 6 ea.
H1 Leveler Insert 274650 4 ea.
H9 Confirmat
Screw 950100 3 ea.
H7 Angle Bracket 401170 2 ea.
H8 Varianta Screw 988060 8 ea.
H3 Hinge Plate 400207 4 ea.
H10 Rafix Cam 909909 12 ea.
HARDWARE
H6 #8 x 5/8"
Panhead Screw 988056 4 ea.
H5 Catch Plate 452340 1 ea.
H12 Hinge 400205 4 ea.
H11 Rafix Bolt 909925 18 ea.

H16 1" Washerhead
Screw 920200 4 ea.
H18 Door Bumper 298030 2 ea.
H17 Door Plate 452330 1 ea.
H14 #6 x 5/8"
Panhead Screw 901216 2 ea.
H23 Connector
Screw 901350 4 ea.
H22 Connector
Sleeve 950200 4 ea.
H15 Handle 400870 2 ea.
H13 Lock & Key Set
452310
452320
452350
1 ea.
H19 Grommet 286580 5 ea.
Hardware for Connecting to Other Glacier Circulation Desk Units.
H20 Rafix Shelf
Cams 909912 6 ea.
H21 Rafix Shelf Pin 909924 6 ea.

ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

Place the Left Side (A) and Right Side (B) on a clean, carpeted surface with the pre-drilled holes
facing up. Insert the Leveler Inserts (H1) into the holes in the bottom edges of each Side. Using a
plastic mallet, tap until flush with the surface. Screw the Levelers (H2) into the Leveler Inserts.
Adjust Levelers when the assembled unit is in place.
#1
#2
#3
Screw nine Rafix Bolts
(H11) into the Left Side
(A) and Right Side (B)
where indicated.
Attach Hinge Plates (H3) to
the Left Side (A) and Right
side (B) using the attached
screws into the pre-drilled
holes where indicated.
H11

Insert six rafix Cams
(H10) into the Top (C)
with the arrows of the
cams facing out.
Attach a Catch Plate (H5)
to the Top as shown
using two #8 x 5/8"
Panhead Screws (H6).
#4
H10
Insert six Flush Rafix
Cams (H4) into the
Back (D) and six Rafix
Cams (H10) into the
Bottom (E) with the
arrows of the cams
facing
out.
#5
Secure an Angle Bracket
(H7) to each end of the
Toeboard (F) using the
Varianta Screws (H8).
#6
H8
H10
H8
H4

Attach the Toeboard (F) to
the Bottom (E) using three
Confirmat Screws (H9)
through the pre-drilled
holes as shown.
#7
H9
NOTE: The Angle
Brackets should be
oriented towards the
inside as shown.
Place the Left Side (A) as
shown. Position the Top
(C) onto the Left Side.
Turn the cams (H10)
clockwise to secure.
#8
Position the Back (D)
onto the Left Side (A)
and turn cams (H4)
clockwise to secure.
#9

Position the Bottom Shelf
(E) and Toeboard (F)
assembly onto the Left
Side (A)
#10
Position the bolts and dowels
of the Right Side (B) onto the
units cams (H4) and (H10)
#11

Insert six Rafix shelf cams (H20) into the Adjustable Shelf (G) with the flat edge facing outwards
and tap until fully seated in place as shown.
Note: The edge of the Rafix Cam must be aligned with the shelf edge. Rafix Cams cannot be
repositioned if installed incorrectly.
#13
With the assistance of
another person, turn the unit
upright. Push three Rafix
Shelf Pins (H21) into pre-
drilled holes of each Side (A
& B) at a selected height.
#14
H21
Secure the Angle Brackets
(H7) of the Toeboard (F) to
the Left Side (A) and Right
Side (B) using Varianta
Screws (H8).
#12
H8
H8