Ironwood GLACIER PBS42DB User manual

0307
PICTURE BOOK
SHELVING
PBS42DB
PBS48DB
DOUBLE BASE UNIT
BY
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].

D
A
PARTS & HARDWARE
B
C
Right Side - PBS42DB
Right Side - PBS48DB 01021141
01021541 1 ea.
1 ea.
Left Side - PBS42DB
Left Side - PBS48DB 01021141
01021541 1 ea.
1 ea.
Top 01021102 1 ea.
Shelves - PBS42
Shelves - PBS48 01024724 4 ea.
6 ea.
H5 Varianta Bolt 988060 16 ea.
H6 Metal Frame 412026 1 ea.
4 ea.
6 ea.
412226
H2 Book Stop - PBS42
Book Stop - PBS48
16 ea.
909931
H4 Tab-V Metal Flange
24 ea.
32 ea.
909930
H1 Tab-V Plastic Housing - PBS42
Tab-V Plastic Housing - PBS48
8 ea.
16 ea.
909932
H7 Tab-V Metal Shelf Clip - PBS42
Tab-V Metal Shelf Clip - PBS48
16 ea.
24 ea.
490571
H8 Wire Divider - PBS42
Wire Divider - PBS48
30 ea.
40 ea.
988056
H3 #8 x 5/8” Panhead Screw - PBS42
#8 x 5/8” Panhead Screw - PBS48

it is important to read all the way through the Adder instructions
(enclosed in the Adder carton) before beginning. It will be necessary to
substitute a Divider (J) for a Right Side (B) during assembly.
NOTE:
The diagrams show one size for ease of viewing.
Any differences will be indicated in each step
’ s text.
If you have purchased an Adder unit
to be assembled in conjunction with this Base unit,
it is important to read through the Back option
and/or Toe Space option directions before beginning.
If you have purchased the Back option or the Toe Space option
to be assembled in conjunction with this Base unit,

Using a plastic mallet, tap in the
plastic housings with the flat
edge facing outwards until flush
with the surface.
IMPORTANT! The flat
edge of the plastic
housing must be
aligned with the shelf
edge. Plastic Housings
cannot be repositioned
once installed.
For a Fixed Shelf or Top,
install the metal flange using a
System (Varianta) Screw as
shown. DO NOT over tighten!
For an Adjustable Shelf, use
the Metal Shelf Clip.
Slide the shelf into place over
the Metal Flanges and push
down until fully seated.
Turn the rotating portion (Cam)
1/2 turn to lock in place.
To remove, simply turn the
Cam counter clockwise 1/2
turn and lift the shelf off of the
Metal Flanges.
ALIGNED
FLAT
EDGE
USING THE TAB-V SYSTEM:
ADJUSTABLE
FIXED

ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
D
H1
H1
H1 H1
H1
#1
Refer to “Using the Tab-V System” on the previous page.
Insert eight Tab-V Plastic Housings (H1) into the Top (C) so that
the flat edge is facing outwards. Using a plastic mallet, tap the
housings until flush with the surface.
The flat edge of the plastic housing must be aligned with
shelf edge. Plastic housings cannot be repositioned once
installed.
C
H1
H1
H1
#2 42” Unit: Insert 16 Tab-V Plastic Housings (H1)
into all four Shelves (D). Refer to Step #1.
48” Unit: Insert 24 Tab-V Plastic Housings (H1)
into all four Shelves (D). Refer to Step #1.

#3
D
H3
H2
Attach a Book Stop (H2) to all Shelves (D)
using Panhead Screws (H3) in the pre-drilled
holes of each shelf.
If you will be installing the Back Option to
this unit, do not attach the Book Stop.
#4
B
TOP SET OF
HOLES FOR
TOP PANEL
4th SET OF
HOLES FOR
BOTTOM SHELF
H4
H3
TOP
A
Place the Side Panels (A & B) on a clean, carpeted surface as shown. Install 16 Tab-V Metal
Flanges (H4) using 16 Varianta Screws (H5) into both panels as shown below.
C
B
Place the Right Side Panel (B) with the pre-
drill holes facing up. Slide the Top (C) onto
the uppermost set of Metal Flanges (H4).
Press the Top down until the Plastic
Housings (H1) in the top are fully seated on
the Metal Flanges (H4) in the side. Turn the
rotating portion of the plastic housing 1/2
turn to lock in place.
#5 Repeat Step #7 for the Bottom (fixed)
Shelves (D), using the bottom set of
Metal Flanges (H4) in the Right Side
Panel (B).
C
B
#6

Position the Left Side Panel (A) onto the
Top (C) and the Bottom Shelves (D). Press
the Shelves down so the Plastic Housings
(H1) of the shelves are fully seated on the
Metal Flanges (H4) of the Left Side. Turn
the rotating portion of the plastic housing
1/2 turn to lock in place.
C
A
DDB
#7 #8 Attach the Metal Frame (H6) to the Right
Side Panel (B) and the Left Side Panel
(A) using ten Panhead Screws (H3) in
the pre-drilled holes.
Make sure the holes of the Metal
Frame are positioned as shown.
If you are installing the Back Option,
DO NOT attach the Metal Frame at this
time. Follow the directions provided
with the Back Option.
A
D
D
C
B
IMPORTANT! If you have purchased the Toe Space option for this unit,
it is recommended to install the Toe Space at this time.
Follow the directions included with the Toe Space option.

#9 With the assistance of another person, turn the unit upright.
42” Unit: Placement of the Middle (adjustable) Shelves (D) is optional. Placement at about
halfway up is recommended. Push 8 Tab-V Shelf Pins (H7) into the Left Side Panel (A) and
the Right Side Panel (B) at the preferred height.
48” Unit: Placement of the Shelves (D) is
optional. Allow room between shelves to
accommodate the Wire Dividers. Push 16 Tab-V
Shelf Pins (H7) into the Left Side Panel (A) and
the Right Side Panel (B) at the preferred height.
#10 Place the Middle Shelves (D) into the unit
and onto the Tab-V Shelf Pins (H7). Turn
the rotating portion of the Plastic Housings
(H1) to secure in place.
ADJUSTABLE
H7

Insert the Divider Wires (H8) into the
pre-drilled holes of the upper surface of
the Shelves (D) shown.
Your Glacier Picture Book Shelving unit is now fully assembled and ready for use.
#11