iWave FNM-8416 User manual

FNM-8416 User Manual
Thank you very much for your favor of our products! This manual describes the usage of the FNM-8416 and
amis to enable you quickly grasp the use of the product.
Version 1.0.1(3)
Date 8/9/2019
IWAVE COMMUNICATIONS Co.,Ltd
To Costumers
添加标题
This document is copyright-protected by IWAVE COMMUNICATIONS co., ltd. Laws in China and/or other
countries or areas protect the exclusive rights of the Company. The Company endeavors to achieve the
accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the
specifications and designs are subject to change without notice due to continuous technological
development. No part of this manual may be copied, modified, translated, or distributed in any manner
without the prior written consent of the Company.
If you have any suggestions or would like to receive more information, please visit our website at:
http://www.iwavecomms.com, or email us [e-mail].
Copyright Information
1

FNM-8416 User Manual
Contents
1. Introduction................................................................................................................................... 3
2. Package List................................................................................................................................... 3
3. Interfaces and Indicator Lights.................................................................................................... 4
4. Network Settings & Installation................................................................................................... 5
4.1. Network Configuration...................................................................................................5
4.2. Installation Steps.............................................................................................................5
5. Cables..............................................................................................................................................6
5.1. TTL Cables.........................................................................................................................6
5.2. Serial Data Format...........................................................................................................7
5.3. Ethernet Cables................................................................................................................7
6. Notice...............................................................................................................................................7
2

FNM-8416 User Manual
1. Introduction
FNM-8416 is a middle range (14~16km) point-to-point drone HD network downlink radio.
2.Package List
3

FNM-8416 User Manual
3. Interfaces and Indicator Lights
ü3 LAN Ports for connecting with 4P Ethernet
cable
üEach LAN port has a LED light below. The
LED will flash when data is transmitting
through the port.
üTTL-serial cable connect with the 5P serial port for
signal transmitting(Vol: 3.3V)
üLED1 will be on when Tx and Rx are communicating
with each other successfully
üLED2 and LED3 are reserved for production testing
üSMA is for antenna connecting
üMicro USB is reserved for production testing
ü4P Power Input Connector (DC 7~18V)
üPower LED
üSMA is for antenna connecting.(Note: Antennas should
be in good connection before power on)
4

FNM-8416 User Manual
4. Network Settings & Installation
4.1. Network Configuration
FNM-8416 units are working as wireless routers, the Tx and Rx connects two different network
segments: 192.168.1.X(Tx) and 192.168.2.X(Rx)
Default IP address:
Transmitter(Tx)
Receiver(Rx)
192.168.1.1
192.168.2.129
IP configuration
Tx
Rx
IP Address
192.168.1.X
192.168.2.X
Gateway
192.168.1.1
192.168.1.129
Mask
255.255.255.0
255.255.255.0
4.2.Installation Steps
①Connect antennas to Tx and Rx with antenna-cables
②Configure the IP/gateway/mask of devices connected with Rx and Tx (Such as IP Camera or PC) according
to Table 2
③Connect power source to Tx and Rx by power cables
④Power on all the devices
⑤After 10~20 seconds, if the wireless communication is established successful, LED1 on Tx and Rx will be on.
⑥If Tx and Rx are connected with serial devices. Please refer to Serial Data Format on P7 for serial
voltage/data format configuration.
Table 2
Table 1
5

FNM-8416 User Manual
5. Cables
5.1. TTL Cables
TTL Serial cable is for transmitting 3.3V TTL signals. One end is 5P JST eGH, the pin number is shown
as below.
Pin
Signal
1
TXD
2
RXD
3
3.3V output, max 500mA (power external device if necessary)
4
GND
5
Reserved
The other end is 3 dupont plugs with different color wire:
Color
Signal
Red
TXD
Yellow
RXD
Black
GND
6

FNM-8416 User Manual
5.3. Ethernet Cable
One end is standard RJ45 and the other end is 4P JST eZH header
6. Notice
üBefore powering on, make sure all the antennas are in good connection. Because Powering on a unit
without antenna as a load, the PAs inside will be damaged
üTwo antennas on Tx or Rx should be kept at a distance as long as possible to avoid interference.
If two antennas are installed very near each other, the wireless signal may become weaker and the
transmission range may be shorter.
7
5.2. Serial data format
Default Baud Rate
115200
Data Bits
8
Parity
No
Stop bit
1
Voltage
3.3V