iWave iW-RainboW-G24M Arria10 SoC FPGA SOM User manual

Arria10 SoC/FPGA SOM
Development Platform
iW-RainboW-G24D
Quick Start Guide

Disclaimer
iWave Systems reserves the right to change details in this
publication including but not limited to any Product specification
without notice.
No warranty of accuracy is given concerning the contents of the
information contained in this publication. To the extent
permitted by law no liability (including liability to any person by
reason of negligence) will be accepted by iWave Systems, its
subsidiaries or employees for any direct or indirect loss or
damage caused by omissions from or inaccuracies in this
document.
Trademarks
Certification
iWave Systems Technologies Pvt. Ltd. is an ISO 9001:2015
Certified Company.
All registered trademarks, product names mentioned in this
publication are the property of their respective owners and used
for identification purposes only.

Introduction
Quick Start Guide (QSG)
This Quick Start Guide (QSG) is designed for users to quickly
understand the iW-RainboW-G24D Arria10 SoC/FPGA SOM
Development Platform and start the evaluation. It provides the
instructions for setting-up the Development Platform from the
packed box.
Development Platform Description
g Arria10 SoC/FPGA with upto 660K logic elements
The iW-RainboW-G24D Arria10 SoC/FPGA SOM Development
platform incorporates with iWave's Arria10 SoC/FPGA based
SOM and High Performance carrier board with all necessary
interface connectors for developing an embedded application
based on Intel Arria10 SoC/FPGA.
Some Key Features of the Board Include:
Quick Start Guide
01
g 2GB HPS DDR4 RAM with ECC
g Micro SD (Boot & OS storage)
g Configuration Flash for FPGA
g Gigabit Ethernet RJ45 Magjack x1
g PCIe x1 Port
g SFP+ Connector
g Dual FMC HPC Connectors
vSX270 / SX480 / SX660
g 4GB FPGA DDR4 RAM
g Dual 12 Pin PMOD Connectors
vGX270/GX320/GX480/GX570/ GX660/GX900/GX1150

This development platform is ESD
sensitive. Handle the product only in
accordance with the installation
instructions given in the manual.
Therefore ESD precautions should be
taken care during transport and
handling.
Safety
iW-RainboW-G24D-Arria10 SoC/FPGA
SO M D eve l o p me n t P l at f or m is
designed by using RoHS and REACH
c o m p l i a n t c o m p o n e n t s a n d
manufactured on lead free production
process.
Check the local regulations for
disposal of electronic products before
disposing.
ESD Protection
Product Disposal
Environmental Compliance
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24D
02
Must use a ESD ground strap or other
grounded source before unpacking or
handling the hardware.

Quick Start Guide
Step 1 - Unpacking
Remove the Development platform from antistatic cover and
place it above the ESD free area. Use anti-static pad/mat with
proper grounding to place the Development Platform. Don't
touch inside surface of the circuit board.
iW-RainboW-G28D
Quick Start Steps
Avoid using board in extreme dust, humidity and temperature
conditions. Also this development platform is not water proof.
Keep away from wet surface.
Package Box
Quick Start Guide
03
Quick Start Guide
iW-RainboW-G28D
Arria10 SoC/FPGA SOM
Development Platform
iW-RainboW-G24D
Quick Start Guide

Make sure that, below deliverables are received without any
physical damage.
12V,5A Power Supply
USB OTG Cable
QSG
Development Platform
Step 2 - What's Inside The Box ?
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24D
04
JTAG Cable
04
Arria10 SoC/FPGA SOM
Development Platform
iW-RainboW-G24D
Quick Start Guide

Quick Start Guide
05
Step 3 - Download FTP Contents
For FTP Credentials, Contact : [email protected]
All the technical resources of iW-RainboW-G24D Arria10
SoC/FPGA SOM Development platform is available in iWave
FTP server.
FTP Folder Structure
iW-RainboW-G30D
Hardware
Datasheet-UserGuides
PCB-CAD Files
QuickStartGuide
SOM-HardwareUserGuide
DevKit-HardwareUserGuide
Fansink-Datasheet
SOM
DevKit
FPGA-Example-Design
Linux
Tools
FPGAUserGuide
ReleaseNotes
SoftwareUserGuide
Binaries
Patch
Integrated Design
IBERT Design
Heatsink-Datasheet
PCB-CAD Files
Mechanical Files
Compliance Report
MPSoC Name
SOM Part Number
Qaurtus Version
Documents
Software+FPGA
Hardware
iW-RainboW-G30D

Step 4 - Read Documents
Before moving to next step, one must go through all the
documents including Hardware User Guides and get familiar
about iW-RainboW-G24D Development platform.
Development Platform Documents:
■ Quick Start Guide (This document)
■ SOM Hardware User Guide
■ DevKit Hardware User Guide
■ Release Notes
■ Software User Guide
■ FPGA User Guide
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24D
06

Step 5 -Quick View-SOM
TOP View
BOTTOM View
1. Arria10 SoC/FPGA
2. Micro SD Connector
3. Configuration Selection switch
4. FAN Header
5. AS Programming Header
6. JTAG Header
7. PMIC Programming Header
8. Board to Board connector 1
9. Board to Board connector 2
07
Quick Start Guide

01. PMOD Connector 2
02. Board to Board Connector 1
03. PMOD Connector 1
04. JTAG Header
05. Board to Board Connector 2
06. GPIO Header
07. RESET Switch
08. ON/OFF Switch
09. Power Jack
10. Debug UART Connector
11. USB OTG Connector
12. EMAC1 Ethernet Jack
13. 2nd Ethernet Jack
14. Display Port
15. Channel Selection Switch
16. SFP+ Connector
17. PCIe X1 Connector
18. SDI IN HD BNC Jack
19. SDI OUT HD BNC Jack
20. Standard SD Connector
21. USB Type C Connector
22. FMC Connector 1
23. CAN Header
24. FMC Voltage Select Switch
25. FMC Connector 2
26. RTC Battery Holder
27. M.2 SATA Connector
Step 6 - Quick View-Carrier Board
TOP View
BOTTOM View
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24DiW-RainboW-G24D
08

Step 7 - On Board Switch Setting
Make sure that On-SOM FPGA Configuration Select Switch
(SW1) is set for PS & FPP (Configuration via HPS) configuration
scheme as shown in below image.
SW1
(1 0)
1 - ON
0 - OFF
Quick Start Guide
09

Install the driver for Debug Port in Host PC/Laptop using the
below link.
https://ftdichip.com/products/ft232rq/
Connect TypeA end of USB cable to PC and MicroB end of USB
cable to Development platform's Debug USB MicroAB
Connector (J5) as shown below.
Step 8 - Debug Port Setting
Setup the Debug Terminal parameters.
Baud Rate : 115200
Data bits : 8
Parity : None
Stop Bits : 1
Flow Control : None
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24DiW-RainboW-G24D
10

Make sure that the micro SD card with bootable image is
inserted in the SOM as shown below.
Step 9 - Micro SD Card Insertion
Quick Start Guide
11
Note: This step is not applicable for the SOMs where MicroSD is
not used as boot device.

Step 10 - Power-ON the Development Platform
Connect the 12V power supply plug to the power connector (J4)
of the Development platform as shown below and switch ON
the power supply.
Warning :
1. Do not try to connect any other power supply other than supplied along
with the Development platform.
2. Do not plug or remove the Arria10 SoC / FPGA SOM from carrier board with
live power.
3. Contact iWave if power LEDs are not glowing.
Once power is applied to the Development platform, the power
LEDs in Arria10 SoC/FPGA SOM and High Performance carrier
board will glow as shown in the below image.
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24DiW-RainboW-G24D
12

Command Prompt
Step 11 - Test Environment setup
Once power is applied to the Development Platform as
explained in the previous section, boot messages being
displayed in the debug terminal of the PC/Laptop which is
connected to the Development platform. Press any key in
terminal immediately to see the command prompt of the Boot
loader or wait until OS boots.
After OS boots, Login prompt being displayed in the debug
terminal. Enter username and password as “root” to get the
Linux command prompt as shown below.
Quick Start Guide
13

JTAG
e
Pin No. 1
JTAG Connection
iW-RainboW-G24D Arria10 SoC/FPGA SOM Development
platform support JTAG interface for FPGA Programming and
debugging. Use the JTAG cable which is shipped with the
development platform to connect SOM and USB Blaster.
USB Blaster-2
Part Number: PL-USB2-BLASTER from Intel
Example USB Blaster which is tested with this Platform is
mentioned below.
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24DiW-RainboW-G24D
14

Quick Start Guide
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24D Arria10 SoC/FPGA SOM Development
platform comes with Heatsink+Fan attached to it. Makesure to
power up the platform only with Heatsink+Fan attached.
Below is the Heatsink+Fan integration procedure for
reference.
Heatsink + Fan Peel off Thermal pad sticker
Paste the heatsink in to
Arria10 SoC
Connect the Fan to SOM
Fan Header
Heatsink
Heat Sink Integration
Quick Start Guide
15

iWave’s Other Products
Product Name: Zynq 7000 SODIMM SOM
Processor: Xilinx Zynq 7000 SoC
RAM: 512MB DDR3*
Application: Industrial Automation,
Industrial Equipments, Machine Vision,
Control & Measurement.
Product Name: iMX8 SMARC SOM
Processor: NXP’s iMX8 QuadMax SoC
RAM: 8GB LPDDR4*
Application: Industrial Control Systems &
HMI, Portable Medical devices, Augmented
& Virtual Reality.
Product Name: Zynq US+ MPSoC
(4/5/7-EV/EG/CG) SOM
Processor: Xilinx’s Zynq US+ MPSoC
(4/5/7-EV/EG/CG)
RAM: 4GB PS DDR4*
1GB PL DDR4*
Application: Industrial Motor Control & IoT,
Sensor Fusion, ADAS/Embedded Vision,
Data Centor, Medical Endoscopy
* RAM size is expandable. Contact iWave team for further details
Product Name: Zynq UltraScale+ MPSoC
(ZU5/ZU4/ZU3/ZU2) SBC
Processor: Xilinx’s Zynq US+ MPSoC
(2/3/4/5-EV/EG/CG)
RAM: 8GB PS DDR4* & 4GB PL DDR4*
Application: AI/ML, Industrial IoT, Human
Machine Interface, Advanced Driver
Assistance Systems.
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G24DiW-RainboW-G24D
16

Need More Help ?
iWave Systems Provides Technical Support to all Customers
Worldwide.
gEmail
Write your technical queries to [email protected]
gPhone
Call us on : [phone], 26781643, 26786245
gLive Chat
We provide Live Chat technical support to our customers.
Contact iWave to enable Live Chat support.
iW-PRFAZ-UM-01-R3.0-REL2.0-QSG
For Return Merchandise Authorization (RMA),
scan the QR code or go to :
https://www.iwavesystems.com/support/rma/
Warranty support for Hardware: 1 Year from iWave or iWave's
EMS partner.
Warranty & RMA
tp
For Warranty terms & Registration, scan
the QR code or go to :
https://www.iwavesystems.com/support/
warranty/
Quick Start Guide
17

USA
JAPAN
iWave Japan, Inc.
8F-B, Kannai Sumiyoshi Building,
3-29, Sumiyoshi-cho, Naka-ku, Yokohama,
Kanagawa, Japan.
Email: [email protected]
Ph: [phone], 26781643
Israel
Value Technologies Ltd.
P.O. BOX 3161, Tel-Mond, Israel
4060000
Tel: [phone]
Fax: [phone]
Email: [email protected]
FRANCE
EUROPE
iWave Europe.
International Sales and Marketing,
Europe.
Venkelbaan 55 2908KE Capelle
aan den Ijssel
Email: [email protected] Our Partners
Across The Globe
RUSSIA KOREA
J.S Communications
#913, Dojung Tower, Anyang-ro 115,
Manan-gu, Anyang-si, Gyeonggi-do, Korea
Tel : [phone]
Email: [email protected]
Headquarters: INDIA
iWave Systems Tech. Pvt. Ltd.
7/B, 29th Main, BTM Layout 2nd Stage,
Bengaluru-560076,India.
Ph: [phone], 26781643
Email: [email protected]
www.iwavesystems.com
FRANCE
EUROCOMPOSANT
1, rue Rene Caudron - BP 15
78960 Voisins-le-Bretonneux,
France
Tel: [phone]
Fax: [phone]
Email: [email protected]
Symmetron
Business-Park River City,
Leningradskoe Shosse 69,
Building 1, Moscow, Russia, 125445.
Tel: [phone]
Email: [email protected]
SWEDEN
Acte Solutions AB
Box 4115,
SE-171 04 Solna,
Sweden.
Tel: [phone] / 46
Email: [email protected]
GLOBAL
Arrow Electronics, Inc.
9201 East Dry Creek Road
Centennial, CO 80112 USA
NA: [phone]
[email protected]
EMEA: [phone]
[email protected]
Asia: [phone]
[email protected]
GLOBAL
Future Electronics
237 Hymus Blvd.,
Pointe Claire, Quebec,
Canada H9R 5C7.
Tel: [phone]
Email: [email protected]
EMEA: [phone]
[email protected]
Asia: [email protected]
GLOBAL
Mouser Electronics, Inc.
1000 North Main Street
Mansfield, Texas 76063,USA
Tel: [phone]
E-mail: [email protected]
TURKEY
ÖZDİSAN ELEKTRONİK A.Ş.
DES Sanayi Sitesi 104 Sokak A07
Blok No: 54-56 Upper Dudullu / Ümraniye
Istanbul - Turkey
Tel: [phone]
E-mail: [email protected]
UNITED STATES
iWave USA
1692 Westmont Ave., Campbell,
CA95008 USA
Ph: 408-206-5958
Email: [email protected]
ONLINE
Digi-Key Corporation
701 Brooks Avenue South
Thief River Falls,
MN 56701-0677
Tel: [phone]
E-mail: [email protected]
Embedded Technologies, Inc
2870 Scott St, Suite 101,
Vista, CA USA,
Tel:[phone],
E-mail: [email protected]
SPAIN
Anatronic
Paseo de los Melancólicos, N° 9-2° A
28005 MADRID, Spain
Tel : [phone]
Email: [email protected]
Batenburg Adelco Electronics
Venkelbaan 55
2908 KE Capelle aan den Ijssei,
The Netherlands
Tel: [phone],
[phone]
Email: [email protected]
NETHERLANDS, BELGIUM