iWave Zynq Ultrascale+ MPSoC Pico ITX User manual

Zynq Ultrascale+ MPSoC Pico ITX
Single Board Computer
iW-RainboW-G36S
Quick Start Guide
R1.0
iW-RainboW-G36S
Quick Start Guide
R1.0

Disclaimer
iWave Systems reserves the right to change details in this
publication including but not limited to any Product specification
without notice.
No warranty of accuracy is given concerning the contents of the
information contained in this publication. To the extent
permitted by law no liability (including liability to any person by
reason of negligence) will be accepted by iWave Systems, its
subsidiaries or employees for any direct or indirect loss or
damage caused by omissions from or inaccuracies in this
document.
Trademarks
Certification
iWave Systems Technologies Pvt. Ltd. is an ISO 9001:2015
Certified Company.
All registered trademarks, product names mentioned in this
publication are the property of their respective owners and used
for identification purposes only.
iW-RainboW-G33D

Introduction
Quick Start Guide (QSG)
This Quick Start Guide (QSG) is designed for users to quickly
understand the iW-RainboW-G36S Zynq Ultrascale+ MPSoC
Pico ITX Single Board Computer (SBC) and start the evaluation.
It provides the instructions for setting-up the Single Board
Computer from the packed box.
SBC Overview
g Zynq Ultrascale+ MPSoC with upto 256K Logic Cells
The iW-RainboW-G36S Zynq Ultrascale+ MPSoC Pico ITX SBC is
an Off-the-self board which contains all necessary interfaces &
on-board connectors required for a complete embedded
application. This board can be used as it is for wide range of
applications.
Some Key Features of the Board Include:
Quick Start Guide
01
g 2GB 64 bit PS DDR4 RAM & 1GB 32 bit PL DDR4 RAM
g 8GB eMMC Flash (Boot & OS storage)
g Dual Gigabit Ethernet RJ45 Magjack
g WLAN & BT Module
g Display Port
g Dual USB 3.0 Type A Port
g M.2 Key B Connector with SATA & USB 3.0
g SFP+ Connector
g SDI Video IN & Video OUT Connectors
g HDMI Video IN & Video OUT Connectors
g Board to Board Connectors with GPIO support
g Pico ITX form factor (100mm x 72mm)

This SBC is ESD sensitive. Handle the
product only in accordance with the
installation instructions given in the
manual. Therefore ESD precautions
should be taken care during transport
and handling.
Safety
iW-RainboW-G36S Zynq Ultrascale+
MPSoC SBC is designed by using RoHS
and REACH compliant components
and manufactured on lead free
production process.
Check the local regulations for
disposal of electronic products before
disposing.
ESD Protection
Product Disposal
Environmental Compliance
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G36S
02
Must use a ESD ground strap or other
grounded source before unpacking or
handling the hardware.

Quick Start Guide
Step 1 - Unpacking
Remove the SBC from antistatic cover and place it above the
ESD free area. Use anti-static pad/mat with proper grounding
to place the SBC. Don't touch inside surface of the circuit board.
iW-RainboW-G28D
Quick Start Steps
Avoid using board in extreme dust, humidity and temperature
conditions. Also this SBC is not water proof. Keep away from
wet surface.
Package Box
Quick Start Guide
03
iW-RainboW-G28D

Make sure that, below deliverables are received without any
physical damage.
12V,5A Power Supply
DVD
SBC
Step 2 - What's Inside The Box ?
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G36S
04
Enclosure
Optional Accessories
FAN with Heat Sink

iW-RainboW-G28D
Step 3 - Read DVD Contents
Given DVD contains below deliverable folders.
1. Binaries
2. Documents
3. Source Code
Delivery binaries are available in Binaries folder and Source
code files are available in Source Code folder. Also Documents
folder contains Hardware User Guide, Software User Guide,
Software Release Note and Quick Start Guide (this guide).
Before moving to next step, one must go through all the
documents including Hardware User Guides and get familiar
about iW-RainboW-G36S Zynq Ultrascale+ MPSoC SBC.
Source code can be customized according to user wish and
corresponding binaries can be generated. Once the binaries
generated, user can download the binaries in to the SBC using
JTAG.
Quick Start Guide
05

Step 4 - Quick View-SBC Top View
01. PL DDR4 RAM
02. Zynq US+ MPSoC
03. PS DDR4 RAM
04. JTAG Header
05. Display Port Connector
06. HDMI IN Connector
07. HDMI OUT Connector
08. Debug UART Header
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G36S
06
09. Dual USB 3.0 Connector
10. Dual Gigabit Ethernet Jack
11. SFP+ Connector
12. Power IN Jack
13. Power ON/OFF Switch
14. RESET Button
15. FAN Header
16. RTC Battery Header

17. Board to Board Connector 1
18. Board to Board Connector 2
19. Board to Board Connector 3
20. eMMC
21. SIM Connector
22. Wi-Fi/BT Module
23. M.2 Key B Connector
Step 5 - Quick View-SBC Bottom View
Quick Start Guide
07

Step 6 - Setting Up
Fan & Heat Sink Mounting
iW-RainboW-G36S
08
Before powering ON the Board, heat sink and fan should be
mounted on top of Zynq US+ MPSoC as shown in below image.

Install the driver for Debug Port in Host PC/Laptop using the
below link.
http://www.ftdichip.com/Products/ICs/FT232R.html
Connect TypeA end of TTL-232R-RPI cable to PC and 3 pin
(100mil) Berg house end of TTL-232R-RPI cable to SBC's Debug
UART Connector (J14) as shown below.
Setup the Debug Terminal parameters.
Baud Rate : 115200
Data bits : 8
Parity : None
Stop Bits : 1
Flow Control : None
Debug Port Setting
Quick Start Guide
09

Quick Start Guide
iW-RainboW-G28D
Power-ON the Development Platform
Connect the 12V power supply plug to the power connector
(J18) of the SBC as shown below and switch ON the power
supply.
Warning :
1. Do not try to connect any other power supply other than supplied along
with the SBC.
2. Contact iWave if power status LED is not glowing or PS Error status LEDs
are glowing.
Once power is applied to the SBC, the power LED in SBC will
glow as shown in the below image.
10
iW-RainboW-G36S

Command Prompt(Linux)
Step 7 - Test Environment setup
Once power is applied to the SBC as explained in the previous
section, boot messages being displayed in the debug terminal
of the PC/Laptop which is connected to the SBC. Press any key
in terminal immediately to see the command prompt of the
Boot loader or wait until OS boots.
iWave supports below mentioned Operating System Release
for iW-RainboW-G36S Zynq Ultrascale+ MPSoC SBC.
Linux 4.19.0 (or h igher)
After OS boots, Login prompt being displayed in the debug
terminal. Enter username and password as “root” to get the
Linux command prompt as shown below.
11
Quick Start Guide

iW-RainboW-G28DiW-RainboW-G28D
Step 8 - System Enclosure Quick view
01. Power IN Jack
02. SFP+ Connector
03. Dual Gigabit Ethernet Magjack
04. Dual USB Connector
05. WLAN Antenna
06. HDMI OUT Connector
07. HDMI IN Connector
08. Display Port
12
Quick Start Guide
iW-RainboW-G28D
iW-RainboW-G36S

Quick Start Guide
13
System Enclosure Setting
Step - 3
Step - 2
Step - 1
Follow below steps for iWave’s system Enclosure setting

iWave’s Other Products
* RAM Size is Expandable.
Product Name: Zynq US+ MPSoC
(4/5/7-EV/EG/CG) SOM
Processor: Xilinx’s Zynq US+ MPSoC
(4/5/7-EV/EG/CG)
RAM: 4GB PS DDR4*
1GB PL DDR4*
Application: Industrial Motor Control &
IoT, Sensor Fusion, ADAS/Embedded
Vision, Data Centor, Medical Endoscopy
Product Name: Zynq 7000 SODIMM SOM
Processor: Xilinx Zynq 7000 SoC
RAM: 512MB DDR3*
Application: Industrial Automation,
Industrial Equipments, Machine Vision,
Control & Measurement, Scientific &
Medical Instruments.
Product Name: Zynq US+ MPSoC
(11/17/19-EG) SOM
Processor: Xilinx’s Zynq US+ MPSoC
(11/17/19-EG)
RAM: 4GB PS DDR4*
4GB Dual PL DDR4*
Application: Video Surveillance, Cloud
Computing, Artificial Intelligence/Machine
Learning, 5G Wireless, High Precision Test
Instrument.
14
iW-RainboW-G28DiW-RainboW-G28D
Quick Start Guide
iW-RainboW-G28D
iW-RainboW-G36S

13
iW-RainboW-G33D
Need More Help ?
iWave Systems Provides Technical Support to all Customers
Worldwide.
gEmail
Write your technical quires to [email protected]
gPhone
Call us on : [phone], 26781643, 26786245
gLive Chat
We provide Live Chat technical support to our customers.
Contact iWave to enable Live Chat support.
gOffice Address
iWave Systems Technologies Pvt. Ltd.
No. 7/B, 29th Main, BTM Layout 2nd Stage,
Bangalore - 560 076, India.
For Return Merchandise Authorization (RMA), below web link,
http://www.iwavesystems.com/support/rma.html
Warranty support for Hardware: 1 Year from iWave or iWave's
EMS partner.
For warranty terms, go through below web link,
http://www.iwavesystems.com/support/warranty.html
Warranty & RMA
iW-PRGGG-UM-01-R1.0-REL0.1-QSG