J D Williams XK172 User manual

Assembly Instructions - Please keep for future reference
Width - 117.2cm
2 Door Media Unit/Low Sideboard
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 38.8cm
Height - 57.6cm
Rev A - 04/09/17
033 xx 8202
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Bottom
(110.2x35.2cm)
9999
Left End
(56x38.2cm)
0001
Right End
(56x38.2cm)
0002
Divider x 2
(46.7x35.2cm)
0003
Door x 2
(47.6x30cm)
0006
Back x 2
(48.4x30.7cm)
0007
Top
(117.2x38.8cm)
9998
Small Shelf x 2
(28.8x33cm)
0004
Large Shelf x 2
(49.4x33cm)
0005
Plinth
(110.2x7.6cm)
9164
If you have damaged or missing panels, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Trim x 2
(56x3.0 x1.2cm)
684xx6531

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 16
Code 760001103
Metal dowel x 16
Code 760003004
ABC
E
DF
I
Panel pin x 20
Code 760001012
Panel pin guide x 1
Code 684004501
GH
JKL
Fully cranked 26mm
hinge x 4
Code 652001120
Hingeplate x 4
Code 653006000
Screw x 8
Code 690001008
Shelf Support x 8
Code 681003001
Bradawl
18mm bolt x 4
Code 700002021
Wooden dowel x 4
Code 770001006
45mm screw x 4
Code 690001075
Handle x 2
Code 644003511
Shelf Pin x 8
Code 760001137
M
L bracket x 2
Code 760001901
12mm screw x 4
Code 690001099
NO

Exploded View
4
0007
0007
0001
0002
0003
0003
0004
0004
0005
0005
9999
0006
0006
9164
684xx6531
684xx6531
9998

Step 1
Assembly Instructions
5
A
x4
A
Fitting cams to the
bottom panel.
Insert 4 metal cams
into the bottom panel
.
Note: Ensure cam arrow
points towards the edge
with the hole.
9999
A
A
x4
Step 2
Fitting cams to the
plinth panel.
Insert 4 metal cams
to the plinth panel .
9164
A
A
A
A
9164
A
B
B
B
B
B
B
B
B
Step 3x8
B
Fitting dowels to the
top panel.
B
B
Insert 8 metal dowels
into the top panel
Note: Insert metal
dowels as far as
shown by arrows. Do not
over tighten.
9998
B
9998
A
A
A
A
9999

Assembly Instructions
6
Step 4
Step 5
B
B
B
B
B
B
B
H
H
H
H
A
A
A
A
Insert 4 metal dowels ,
2 hinges and 2
cams into the left end
panel .
Repeat on the right end
panel .
Attach dowels, cams
and hinges to both of
the end panels.
B
A
H
Insert 2 cams
and 2 wooden dowels
into the divider
panel .
Repeat on remainding
divider.
Attach dowels, cams to
both divider panels.
0001
0002
0003
x8
BA
x4
A
A
x4
x4
H
J
J
x4
0001
0002
B
A
A
J
J
0003
Holes not used at
this stage.
X 2

Assembly Instructions
7
Step 6
Attach hinges and
handles to the doors
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
G
c: Secure hinges to
doors using screws .
G
K
d: Secure handle to
doors using bolts
Repeat on the second
door.
E
I
G
G
x4
K
x8
E
x4
I
x2
A
B
C
D
Bradawl
90
Correct
98
Incorrect
I
0006
G
G
K
K
KK
E
E
0006
0006
0006

Assembly Instructions
8
Step 7
Step 8
Connect the top panel
to the left end panel
and the divider panels.
Connect the dowels in the
top panel to the
dowels in the left end
panel and divider
panels .
0001
0003
0003
9998
Turn cams 180 degrees to
lock.
Turn cams 180 degrees to
lock.
Edged face
0003
0003
0001
9998
Large silver fittings
visible in this face
Large silver fittings
visible in this face
IMPORTANT.
Please ensure divider
panels are
positioned as shown.
Connect the bottom
and the plinth panel to
the left end panel.
Connect the dowels in the
left end panel to
the cams in the bottom
panel and the
plinth panel .
Ensure that dowels in both
panels locate
into bottom panel
guide holes.
0001
9999
9164
Edged face
9890
0001
9999
9164
0003
0003
9999
0003
Ensure plinth sits
flush.
Ensure plinth is
not overhanging.

Assembly Instructions
9
Step 9
Step 10
Connect the right end
panel to the top,
bottom and plinth
panel.
Connect the dowels in
the top panel to
the cams in the right end
panel .
Connect the dowels in
the right end panel
to the cams in the bottom
panel and the
plinth panel .
9998
0002
0002
9999
9164
9890
9999
9164
0002
9998
Secure the bottom
panel to the divider
panels.
Using 4 screws ,
secure the bottom panel
to the divider
panels .
9999
0003
L
0003
0003
x4
L
9890
9999
L
L
L
L
Lay unit on its front to
attach the backpanels
Turn cams 180 degrees to
lock.

Assembly Instructions
10
Step 11
Step 12
Measure to
external corners
Squaring up the unit.
Ensure a tape
measure is used
to square up unit!
Important:
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
DIAG 1 DIAG 2 DIAG 3
XX
XX
XX
YY
YY
XX
YY
XX
XX
YY
YY
XX
XX
YY
YY
YY
Attach the backpanel
D
x20
F
x1
D
F
D
Ensure that the
backpanel is fully
inserted into groove.
Slide the back panel into
the end and top panel
grooves.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
D
Plain chipboard surface.

Assembly Instructions
11
Step 13
Step 14
Lay unit on its back
to attach the trims
Locate the notch on
the trim into the grooves
in the end panels.
To insert trims use a
hammer, place a
cardboard packing piece
between the hammer
and trims to
protect the trims.
Ensure that the trims
are inserted fully.
x8
C
Insert 8 shelf supports .
Once inserted, seat shelves
on top of the shelf
supports.
Fitting the shelf
supports.
C
Stand Unit Upright.
0004
Your trims may have a
protective film on. Please
remove this after assembly

Assembly Instructions
12
Step 15
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
Hanging doors
b: Tighten screw shown
to lock hinges in
position.
See ‘Hinge adjustment’
page if the doors
need adjusting.
Repeat the process on
the remaining door.
BB
B
Ensure the underside of screw
B slides into slot on hingeplate.
Hinge correctly attached to
hingeplate.
Hinge incorrectly attached to
hingeplate.
Diagram 1 Diagram 2 Diagram 3
AB
Step 16
Insert the shelf pins
and insert shelves.
Insert 8 of the shelf pins
into the 2 divider
panels at
your desired height.
Place the shelves
on top of the shelf pins.
0003
0005
M
M
M
M
x8
M
M

Assembly Instructions
13
Step 17
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
Hinge adjustment
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
A
B
C

Assembly Instructions
14
Step 17
Congratulations!
Your unit is complete
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
O
N
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
Warning:
2 people to lift.
Lift with care.
With help move the
unit into position.
Warning:
x2
x4
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
An attachment device is provided with your
product. However you will need to source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
Alwasy ensure the wall to be drilled is free
from hidden electrical wires, water and gas
pipes.
Use the wall attachment device provided.
Never allow children to climb or hang on
drawers, doors or shelves.
Place heaviest items in the lower drawers
or shelves.
Unless specifically designed to accomodate,
do not set TV’s or other heavy objects on
top of this product.
Never open more than one drawer at a time.
WARNING

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)