J D Williams AT HOME NEW ENGLAND UNDERBASIN CUPBOARD... User manual

464/3944
Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help of have damaged or missing parts, calls the JDW Customer Helpline: 0871 231 2000
Dimensions No. people Assembly Time
Width: 60.5cm
Depth: 30cm
Height: 61cm (approx.)
30 Mins
NEW ENGLAND UNDERBASIN CUPBOARD CAT NO: QN910
CAT NO: UM239

2
Components -Panels
Please check you have all the panels listed below
Components - Fittings
Note:
may be supplied than are required.
Tools required
Phillips screwdriver
(medium & large)
1x1
60. 5X30X1. 5cm
2x1
59. 5X28. 5X1. 5cm
3x1
59. 5X28. 5X1. 5cm
4x1
54. 5X28X1. 2cm
5x2
51X27X1. 2cm
6x1
54. 3X25. 5X1. 2cm
7x1 8x2
54. 6X7. 5X1. 2cm 53X16. 5X0. 3cm
Ax14
5. 8x30mm
Bx8 Cx8
12x10mm
Dx1
6x25mm
Ex2 Fx2
Gx2 Hx2
3x10mm
J x4
Kx14 Lx4
Mx4
4x16mm
2. 5x10mm
Nx2
3x16mm
I x4
Ox2

3
m

4
Assembly Instructions
F
E
E
F
Step 1
1. Insert 4 x Dowels A
into Left side panel 2
and 4 x Dowels into Right
Side panel 3
2. Insert 2 x Male
Camlocks into Left
Side Panel 2 and Right
side panel 3.
Step 3
Step 4
1. Into the underside of
Top Panel 1 , insert 4 x
male Camlocks and
4 x Dowels as shown
C
A
C
B
2
2
3
2
3
C
A
C
A
C
A
C
A
C
A
C
A
C
A
C
B
C
B
C
B
C
A
2
3
C
B
2
3
1. Connect Base panel 4
and Base Plinth 7 to
Left Side Panel 2.
2. Connect Base panel 4
and Base Plinth 7 to
Right Side Panel 3.
3. Into the underside of
Base Panel 4 insert
4 x Female Camlocks
and tighten with a
Phillips Screwdriver
2
3
4
4
7
4
C
C
2
3
4
7
C
C
C
C
C
C
C
C
1
C
B
C
A
C
B
C
A
C
B
C
A
C
B
C
A
1
C
B
C
A
4
Step 2
4
7
C
A
C
A
1. Insert 2 x Dowels A
into Front plinth 7 as
shown.
2. Connect Front Plinth
7 to base 4 as
shown
C
A
7
74
7

8
8
5
Assembly Instructions
Step 5
Step 6
Step 7
1. Insert 4 x Hinge pins
into the Top and Bottom
of Doors 5
2. Locate the bottom
Hinges into Holes in Base
panel 4.
3. Locate Top Hinge into
Hole in the underside of
Panel 1.
4. Connect Top Panel 1
to Left and Right Panel
and Insert 4 x Female
Camlocks into holes
in Left and Right side
panels. Tightening with a
Phillips Screwdriver
5. Insert 4 x Shelf
Supports I
4
C
J
5
1
1
1. On the reverse of the
unit Connect 2 x Back
panels 9 using
14 x Screw M as
shown
C
K
8
1. To the doors fit 2 x
Catch plate F using 2 x
Screw E.
2. Fit your choice of
handle (G or O) using
2 x Screw H
3. To the underside of
Top Panel 1 connect
1 x Magnetic Catch
using 2 x Screw L .
4. Insert Shelf
C
E
C
F
C
G
C
O
C
H
1
C
L
6
G
G
E
E
F
F
L
4
C
J
C
J
C
J
C
J
C
C
C
I
C
I
C
I
C
I
1
5
5
C
I
8
8
C
K
C
K
C
K
C
K
C
K
C
K
C
K
C
K
6
6
C
G
C
G
C
E
C
E
C
F
C
F
C
L
C
D
C
K
C
K
C
K
C
K
C
K
C
K
C
H
C
H

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers
WARNING
In order to help prevent overturning –
To help prevent product toppling over please follow the below steps:-
Do not allow children to climb or hang on the furniture
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
You will need to provide wall plugs and screws applicable for your wall type

Assembly Instructions
Step 8
6
Step 9
1. Add 4 x Protective
feet M
C
M
C
M
C
M
C
M
C
L
C
L
C
N
C
N
The unit is floor
standing, but it is
recommended that the
unit is secured to the
wall.
2. Move the unit into
desired position.
3. Mark the wall with a
suitable scribe the
position of the fixing
hole.
4. Drill hole and insert a
suitable Wall Plug,
Please check the type of wall
you are fixing to and for more
information please see the
guide to wall mounting
& Fixings on the back page
Warning:
Before driling,check
wall for hidden pipes
and cables.
5. Secure the strap to the
wall using a suitable
wall screw
Note: To hide the straps
behind the unit, drill the
holes lower than the top of
the unit
Assembly Complete
1. On the reverse of the
unit, in position shown, fix 2
x Wall Straps using 2 x
Screws L
C
N
C
L