fantastic furniture Ashford Dresser 7 Drawer User manual

ersion 2.0
Ashford
Dresser 7 Drawer
www.fantasticfurniture.com.au

Enjoy
Your purchase from
Australia’s Best alue Furniture Store
PAGE 2
www.fantasticfurniture.com.au
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
A OID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been provided with a
wall strap to prevent toppling. We strongly recommend that this product is
permanently fixed to the wall or other suitable surface. Fixing devices are
not included since different surface materials require different attachments.
Please seek professional advice if you are in doubt of what fixing device to
use.

PAGE 3
Assemblychecklist
Useful Information
Read through the instructions carefully
before you begin.
Make sure you have all the required tools.
Never use power tools unless instructed.
Identify and lay out all of the components
before you begin assembly.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk bed should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.

PAGE 4
www.fantasticfurniture.com.au
Please make sure you have all these parts before you start.
1 x Wall strap
(H16)
Top Panel
(P1)
Drawer
Side (P13)
Drawer Front
(P17)
Drawer
Side (P13)
Drawer
Side (P13)
Drawer Back
(P18)
Right Side
(P3)
Left Side
(P2)
Side Plinth
(P4)
Side Plinth
(P4)
Top Panel rail
(P5)
Large Drawer
Front (P12)
Large
Drawer
Side (P13)
Large Drawer
Base (P15)
Large Drawer Back
(P14)
Drawer Support
Rail(P16)
Back Panel
(P11)
Back Panel
(P11)
Centre Rail
(P22)
X6
Centre
Panel
(P20)
art LIst
Box 1:
1 x Top Panel (P1);
1 x Left Side (P2);
1 x Right Side (P3);
2 x Side Plinth (P4);
1 x Top Panel Rail (P5);
4 x Front Rail (P6);
1 x Front Plinth (P7);
1 x Front Support Rail (P8);
1 x Back Rail (P9);
1 x Back Support Rail (P10);
2 x Back Panel (P11);
What you Need
To Assemble the roduct
(Other Tools You Need)
Phillips Head Screwdriver
Mallet
1 x Large Drawer Front (P12);
14 x Drawer Side (P13);
1 x Large Drawer Back (P14);
1 x Large Drawer Base (P15);
2 x Drawer Support Rail (P16);
6 x Drawer Front (P17);
6 x Drawer Back (P18);
6 x Drawer Base (P19);
1 x Centre Panel (P20);
1 x Front Rail (P21);
1 x Centre Rail (P22);

Step 2
PAGE 5
www.fantasticfurniture.com.au
Step 1
You will need:
6 x Cam bolts
(H1)
(P1)
x 6
Fix 6 x Cam Bolts (H1) to Top Panel (P1) by using a Phillips head screwdriver.
You will need:
3 x Wood
Screws
(H4)
Attach Top Panel Rail (P5) to Top Panel (P1) by using 3 x Wood Screws (H4) .
(P1)
(P5)
Phillips head
screwdriver
Phillips head
screwdriver

Step 3
Step 4
www.fantasticfurniture.com.au
You will need:
2 x Wooden
Dowels
(H3)
PAGE 6
4 x Left
Runner Track
(H11)
12 x Wood
Screws
(H9)
(H9)
You will need:
2 x Wooden
Dowels
(H3)
3 x Left
Runner Track
(H11)
18 x Wood
Screws
(H21)
(H21)
(H21)
3 x Right
Runner Track
(H12)
x 2
Insert 2 Wooden Dowels (H3) to Left Side (P2).
Fix 4 Left Runner Track (H11) to Left Side (P2) by using 12 Wood Screw (H9) and a Phillips
head screwdriver.
Insert 2 Wooden Dowels (H3) to Center Panel (P20).
Fix 3 Right Runner Track (H12) to Center Panel (P20) by using 9 Wood Screws (H21) and a
Phillips head screwdriver.
Turn over the Center Panel (P20), fix 3 Left Runner Tracker (H11) on Center Panel (P20) by using
9 Wood Screws (H21) and a Phillips head screwdriver.
Phillips head
screwdriver
Phillips head
screwdriver Mallet
Mallet

Step 5
Step 6
www.fantasticfurniture.com.au
You will need:
You will need:
4 x Right
Runner Track
(H12)
12 x Wood
Screws
(H9)
3 x Wood
Screw
(H4)
PAGE 7
2 x Wooden
Dowels
(H3)
6 x Cam bolts
(H1)
x 6
x 4
(H9)
(P3)
(P4)
(P2)
Insert 2 Wooden Dowels (H3) to Right Side (P3).
Fix 4 Right Runner Track (H12) to Right Side (P3) by using 12 Wood Screw (H9)
and a Phillips head screwdriver.
Attach Side Plinth (P4) to Left Side (P2) by using 3 Wood Screws (H4) and a Philip
head screwdriver.
Fix 6 x Cam Bolts (H1) to Left Side (P2) by using a Phillips head screwdriver.
Phillips head
screwdriver
Phillips head
screwdriver
Mallet
Note the position of
Bevelled edge.

You will need:
18 x Wooden
Dowels
(H3)
You will need:
3 x Wood
Screw
(H4)
6 x Cam bolts
(H1)
(H1)
Step 8
Step 7
www.fantasticfurniture.com.au PAGE 8
x 2
(H3)
(H3)
x 4
(H1)
2 x Cam bolts
(H1)
Attach Side Plinth (P4) to Right Side (P3) by using 3 Wood Screws (H4) and a Philip
head screwdriver.
Fix 6 x Cam Bolts (H1) to Right Side (P3) by using a Phillips head screwdriver.
Insert Wooden Dowels (H3) to Front Rail (P21), Back Rail (P9), Front Rails (P6), Back
Support Rail (P10), Front Support Rail (P8) and Bottom Support Rail (P22).
Phillips head
screwdriver
x 2
Phillips head
screwdriver
Mallet
Note the position of
Bevelled edge.

Step 10
You will need:
Step 9
www.fantasticfurniture.com.au PAGE 9
You will need:
5 x Wood
Screws
(H4)
(P8)
2 x Cam
Nut
(H2)
Attach Front Support Rail (P8) to Front Plinth (P7) by using 5 Wood Screws (H4) and a
Philip head screwdriver.
Attach Front Suport Rail (P8) and Back Support Rail (P10) to Bottom Support Rail
(P22), insert Cam Nut (H2) into Centre Rail (P22), rotate the Cam Nuts so the arrow
point towards the incoming cam bolt, turn clockwise to lock.
(H4)
x 2
(P8)
(P10)
(P22)
Phillips head
screwdriver
Phillips head
screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Note the position of
Bevelled edge.

Step 11
Step 12
www.fantasticfurniture.com.au PAGE 10
Attach Bottom Support Rail to Centre Panel by using Screws (H22) and Allen Key (H23).
Attach Back Rail (P9) And Front Rail (P21) to Center Panel by using Screws(H22) and
Allen Key (H23).
You will need:
Attach Front Rail (P6) to Center Panel (P20), insert Cam Nut (H2) into Rails (P6),
rotate the Cam Nuts so the arrow point towards the incoming cam bolt, turn clockwise
to lock.
4 x Cam
Nut
(H2)
2 x Cam bolts
(H20)
x 4
x 2
You will need:
4 x Wood
Screws
(H22)
1 x Allen
Key
(H23)
x 4
Phillips head
screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

You will need:
6 x Cam
Nuts
(H2)
Step 14
Step 13
www.fantasticfurniture.com.au PAGE 11
Attach Left Side (P2) to Rails as shown, insert Cam Nut (H2) into Rails (P6, P8), rotate
the Cam Nuts so the arrow point towards the incoming cam bolt, turn clockwise to lock.
You will need:
6 x Cam
Nuts
(H2)
Attach Right Side (P3) to the rails as shown, insert Cam Nut (H2) into Rail (P6, P8),
rotate the Cam Nuts so the arrow point towards the incoming cam bolt, turn clockwise
to lock.
Phillips head
screwdriver
Phillips head
screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
x 6
x 6

You will need:
Attach Top Panel (P1) to the unit as
shown, insert Cam Nut (H2) into
Side Panels (P2, P3), rotate the
Cam Nuts so the arrow point
towards the incoming cam bolt, turn
clockwise to lock.
6 x Cam
Nuts
(H2)
Slip Back Panels (P11)
into the grooves on the
side panels.
Step 16
Step 15
www.fantasticfurniture.com.au PAGE 12
Phillips head
screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P11)
informative
label nearby
top
(P11)
x 6

Step 17
Step 18
www.fantasticfurniture.com.au PAGE 13
You will need:
4 x Nuts
(H5)
4 x Wood
Screws
(H6)
(H5)
x 4
4 x Wood
Screws
(H15)
(H15)
You will need:
2 x Cam bolts
(H18)
(P12)
Fix small Cam Bolts (H18) to Large Drawer Front (P12) by using a Phillips head
screwdriver.
Fix Screws (H15) between 2 pieces of Back Panels (P11) to Back Rai l(P9)
with 4 Wood Screws(H15). Fix Back Panel Support (H5) to each
cornor on the back with Wood Screws(H6).
Phillips head
screwdriver
Phillips head
screwdriver

Step 20
Step 19
PAGE 14
You will need:
4x Wood
Screws
(H10)
(P12)
(P13)
(P13)
You will need:
Attach Drawer Support Rail (P16) to Large Drawer Front (P12), insert Small Cam
Nuts (H19) into Rails (P16), rotate the Cam Nuts so the arrow point towards the
incoming cam bolt, turn clockwise to lock.
2 x Cam
Nuts
(H19)
www.fantasticfurniture.com.au
Fix DrawerSides (P13) to Large Drawer Front (P12) by using Wood Screws (H10).
Phillips head
screwdriver
Phillips head
screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

Step 21
Step 22
www.fantasticfurniture.com.au PAGE 15
Use Wood Screws (H10) to fix Drawer Back panel to
Drawer Sides and Drawer Support Rails.
You will need:
8 x Wood
Screws
(H10)
Slip Large Drawer Base (P15) into the grooves on the Large Drawer Sides.
Phillips head
screwdriver
With lamination
face inside

Step 23
Step 24
www.fantasticfurniture.com.au PAGE 16
You will need:
4 x Screws
(H7)
2 x Handles
(H8)
You will need:
6 x Wood
Screws
(H9)
1 x left
Runner
(H13)
1 x Right
Runner
(H14)
(H9)
(H14)
(H13)
Fix Left Runner (H13) and Right Runner (H14) to drawer side panels by using
Wood Screws(H9) and a Philip head screw driver.
Fix Handles (H8) on Drawer Front with Screws (H7).
Phillips head
screwdriver
Phillips head
screwdriver

You will need:
24 x Wood
Screws
(H10)
X6
x 4
PAGE 17
Step 25
Step 26
X6
Attach Drawer Side (P13) to Drawer Front (P17) by using Wood Screw (P10) and a
Philip head screw driver.
Slip Drawer Base (P19) into the grooves on the Drawer Sides.
Phillips head
screwdriver
with
lamination
face inside
www.fantasticfurniture.com.au

Step 28
www.fantasticfurniture.com.au PAGE 18
X6
You will need:
24 x Wood
Screws
(H10)
You will need:
12 x Screws
(H7)
6 x Handles
(H8)
x 4
x 2
Step 27
X6
Use Wood Screws (H10) to fix Drawer Back Panel (P18) to Drawer Sides.
Fix Handles (H8) on Drawer Front with Screws (H7).
Phillips head
screwdriver
Phillips head
screwdriver

Step 29
Step 30
www.fantasticfurniture.com.au
You will need:
X6
36 x Wood
Screws
(H9)
6 x left
Runner
(H13)
6 x Right
Runner
(H14)
PAGE 19
(P12)
Fix Left Runner (H13) and Right Runner (H14) to drawer side panels by using
Wood Screws (H9) and a Philip head screw driver.
Slide the drawers into the carcase
of the dresser, large drawer box
place on the top, the other drawer
boxes are the same.
Phillips head
screwdriver