For LPL-P2-WHT-12, LPL-P2-WHT-120, LPL-P2-WHT-12-SQ, LPL-P2-WHT-120-SQ
J&J ELECTRONICS, INC. 3-YEAR LIMITED WARRANTY
Operation
For LPL-P2-WHT-12, LPL-P2-WHT-120, LPL-P2-WHT-12-SQ, LPL-P2-
WHT-120-SQ PureWhite Replacement LED In-Ground Pool Lamps
For more information about this or other J&J Electronics lighting products, please visit www.purewhitepoollight.com. Rev. 012114
©2014 J&J Electronics, Inc. All rights reserved. PureWhite is a trademark of J&J Electronics, Inc. All registered and trademarked brands and names are the property of their respective companies.
PAGE 2
J&J Electronics • 6 Bendix, Irvine, CA 92618 USA • 800.735.4553 • 949.455.4460 • www.jandjpoolspa.com
STEP 8
Check for air bubbles when light is turned ON
STEP 3
Inspect your light housing for signs of wear
STEP 4
Dry the light housing and lens
STEP 5
Install PureWhite lamp
STEP 6
Reassemble the light housing
STEP 7
Submerge assembled light into the water
Figure 3: Steps 2-4
WARNING! Always use a new lens gasket
whenever reassembling your pool light housing.
J&J Electronics,Inc. (“J&J”) warrants the above-referenced model numbers of PureWhite LED In-ground Pool Lamp (the “Product”) to be free from defects in material and workmanship,under normal use,conditions
and service, for a period of three (3) years from the original date of purchase, subject to the terms specified herein. If during the first twenty-four (24) months of the warranty period, the Product fails to operate due
to a defect in material or workmanship, J&J will, at its option, repair or replace the Product at no charge. If during months twenty-five (25) through thirty-six (36), the Product fails to operate due to a defect in
material or workmanship,J&J will grant the purchaser a pro-rated credit
1
for purchase of a J&J replacement part, as the purchaser’s sole remedy. Pro-rated credit is calculated as follows:
TERMS AND CONDITIONS
This warranty is available to the original purchaser of the product(s) only. This warranty applies only when products are properly installed in an in-ground pool; any other use voids the warranty. Products must be
used in lighting equipment designed and approved for the application and in environmental conditions within the normal specified operating range. This warranty does not apply to any abnormal use of product(s),
use in violation of any applicable standard,code or instructions for use in installations including those contained in the latest National Electrical Code (NEC), the Standards for Safety of Underwriters Laboratory, Inc.
(UL), Standards for the American National Standards Institute (ANSI). This warranty will not apply in the event of conditions demonstrating abnormal use or stress, freezing, operating when not fully submerged,
under/over voltage/current conditions, excessive switching cycles or operating hours or outside the recommended operating conditions. This warranty does not apply to color shifts or dimming caused by emissions
and/or LED color shifts and dimming that naturally occurs over time.Warranty conditions: If the product operates for 15 or more hours per day or continuously for 24 hours per day, the product warranty period
stated shall be reduced to half the stated period.This warranty does not cover damage occurring during shipment,damage or failure resulting from alteration,accident,acts of God,theft,abuse,negligent installation,
improper service, unauthorized repairs, freezing or where adequate care has not been taken to prevent damage to the product(s).Tampering with any internal component of this product(s) will void the warranty.
This warranty gives you specific rights. You may have other rights that vary according to the laws of your state.
LIMITATION OF LIABILITY
THE FOREGOING SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE PURCHASER AND IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ALL WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OR TRADE. THE LIABILITY OF J&J UNDER THIS WARRANTY SHALL BE LIMITED
TO THE REPLACEMENT, REPAIR OR PRO-RATED CREDIT OF THE PRODUCT AS STATED HEREIN. J&J IS NOT RESPONSIBLE FOR SHIPPING OR TRANSPORTATION COSTS RELATED TO OBTAINING WARRANTY SERVICE.
IN NO EVENT SHALL J&J BE LIABLE FOR ANY OTHER COSTS OR DAMAGES, INCLUDING LOST PROFITS OR REVENUES, LABOR CHARGES OR FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES.
J&J reserves the right to change the warranty, warranty period without prior notice and without incurring obligation.
T
o obtain warranty
service,
retain the failed Product,
retain the installation invoice showing product purchase pric
e and contact J&J Electronics,
Inc.
at 800.735.4553 ext.
242 or
[email protected].
As of 1/21/14
1Credit is only redeemable by the purchaser through J&J and will be applied against the current MSRP of the product purchased.
2 Product Price is the price at which the product was purchased as stated on the purchaser’s invoice and may not exceed the MSRP for the product at the time of the purchase.
Product Price ($)
2
x Unexpired warranty period (months)
Total Warranty Period (months)
Inspect the rubber grommet where the power cord enters the light for excessive
deterioration. Inspect the light housing, the tensioning clamp, and face ring for
warping, dents and excessive rust. Do not install PureWhite into a pool light housing
that appears to be worn out from prolonged exposure to pool water or mishandling.
compatibility” section at the beginning this manual for details.
Set the lens and faceplate in the light housing and re-assemble according to the light
housing manufacturer’s specification. Tighten the screws or clamp slightly, allowing
the gasket to seal evenly.
Once the screws or clamp are tight, submerge the assembled light housing in the
water and visually check that air bubbles are not escaping from the gasket area.
Should bubbles appear, immediately remove the light housing from the water and
reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation by
wrapping the cord around the light housing and re-attaching the light housing to the
niche assembly.
Reconnect power to the pool light by resetting the circuit breaker to the “ON” position.
Go back to the light location and check for air bubbles rising to the surface from the
pool light housing for at least 10 minutes. It is important that the lamp is turned on
during this time.
If you do not see air bubbles rising to the surface at anytime during the 10-minute
inspection process, the housing is holding its water tight seal and the installation is
complete. You are now ready to enjoy your new PureWhite Replacement LED
In-Ground Pool lamp. If you do see air bubbles rising to the surface at anytime during
the inspection process, immediately remove the PureWhite lamp from the housing,
dry it completely and reset the gasket and lens. Make sure that the PureWhite lamp
and light housing are completely dry before reassembling.
If the pool light housing continually leaks water after 2 or more attempts at
installation, replacement of the pool light housing may be necessary.
Please read the J&J Electronics”PureWhite Quick Start Guide” for further installation
advice.
Note on Figures 1-3: All figures are provided for illustration purposes only. Refer to
the original pool light manufacturer’s installation manual for further reference.
Use the pool’s current light switch to turn “ON” and “OFF” your new PureWhite lamp.
Make sure the inside of the light housing and glass lens are completely dry by wiping
them down with a clean rag.
Remove the old lamp and discard. Carefully screw the PureWhite lamp into the socket.
Proceed by cleaning any gasket residue from the light housing body. A clean surface
is necessary for the new gasket to seat properly and prevent leakage. Install the new
gasket onto the glass lens.
Failure to install a new lens gasket could result in water leakage which can
permanently damage the PureWhite lamp and cause serious injury or death due to
electrical shock.
The product warranty is voided if the proper gasket is not installed. See the “Gasket
