J&J Electronics PureWhite LPL-P1-WHT-12-S Operating instructions

WARNING! This device is not intended for use
with emergency exit fixtures or
emergency exit lights.
WARNING! Permanent damage to the low
voltage 14VAC lamp will occur if installed
on a 120VAC circuit.
PureWhite Replacement LED In-Ground Pool and Spa lamps are available
in 14VAC (low voltage) and 120VAC models as indicated on the product
packaging. Each lamp has a screw-in Edison base.
WARNING! Remove warning label from
PureWhite lens before installation.
[Applies only to model #s: LPL-P1-WHT-12-S and LPL-P1-WHT-120-S]
The warning label is placed on top of a special optical diffuser designed
to maximize the light projection of the PureWhite lamp. When you remove
the label, a protective film will come off with it. Once the warning label
and protective film have been removed, do not allow the diffuser decal
underneath to be scratched.
ATTENTION 14V PUREWHITE OWNERS!
A socket voltage range of 13.5 – 15.0 will achieve optimal brightness.
To verify the voltage, at the lamp socket, measure the open circuit
voltage (no lamp in the socket). Set the transformer tap to 14.0VAC.
DANGER!
Risk of electrical shock or electrocution
Always disconnect power to the pool or spa light at the circuit
breaker panel before attempting to service the lamp. Failure to do so could
result in serious injury or death due to electrical shock. Refer to the original
manufacturer’s light installation manual before proceeding. As with any
electrical device, installation and service should always be performed by
a qualified individual. This device is not intended for use in anything
other than in-ground pools or spa.
Rated Lamp Life
The illumination generated by the PureWhite Replacement LED In-Ground
Pool or Spa lamp is based on Light Emitting Diode (LED) technology. The
average expected lamp life is rated up to 25,000 elapsed time hours under
normal operating conditions. [Temperature: 33°F to 104°F (1°C to 40°C),
Humidity: 0-95% non-condensing].
Safety Precautions
• Do not open, service or tamper with any internal component of the
PureWhite Replacement LED In-Ground Pool or Spa lamp. Doing
so will void the warranty. Follow each instruction in this owner’s
manual and pay careful attention to all warnings.
• Do not directly expose or immerse the PureWhite Replacement LED
In-Ground Pool or Spa lamp in water without containing it in a
proper, watertight, NRTL (nationally recognized testing laboratory)
light housing and niche assembly.
• Keep the light housing dry.
• Handle the PureWhite Replacement LED In-Ground Pool lamp with
care. Be careful not to drop the unit.
IMPORTANT NOTE:
PureWhite lamps are recommended for installation by a qualified pool or
spa professional.
J&J Electronics • 35 Hammond, Irvine, CA 92618 USA • 800.735.4553 • 949.455.4460 • www.jandjpoolspa.com
PAGE 1
PureWhite™Pool & Spa Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL & SPA LAMPS
Model #s: LPL-P1-WHT-12-S, LPL-P1-WHT-120-S, LPL-M1-WHT-12, LPL-M1-WHT-120
PureWhite Replacement LED In-Ground Pool and Spa lamps offer superior, bright white illumination for your pool or spa. This owner’s manual contains
important information on installing and using your new PureWhite Replacement LED In-Ground Pool or Spa lamp. Please read it carefully and keep it in
a safe place for future reference.
Installation
The installation steps in this owner’s manual
are intended as guidelines. For specific
instructions on how to replace a pool or spa
lamp, please refer to the original manu-
facturer’s light installation manual before
proceeding.
Light housing compatibility
LPL-P1-WHT-12-S, LPL-P1-WHT-120,
LPL-M1-WHT-12, and LPL-M1-WHT-120
PureWhite Replacement LED In-Ground
Pool and Spa lamps must be installed in
a compatible NRTL pool light housing.
Compatible NRTL light housings include:
Hayward®Astrolite™SP058 Series
Pentair®Amerlite 784 Series
Jacuzzi®Full Moon™
Hayward®Astrolite™II SP059 Series
Pentair®SpaBrite™Series
WARNING!
Read this before attempting installation
Your PureWhite lamp is not an ordinary light bulb. It is a valuable
electronic device that is not designed to come in direct contact with water.
An improper installation that results in water leakage into the light housing
can permanently damage the PureWhite lamp. Please read these
installation steps and the original manufacturer’s light installation manual
carefully before proceeding.
STEP 1
Remove light housing from niche
Make sure power to the pool or spa light is turned off at the circuit breaker.
Carefully remove the existing light housing from the niche assembly and
place it on the deck. There should be enough power cord to do this easily.
If there is not enough power cord to allow the light housing to reach the
deck surface, call your local pool or spa service company.
WARNING! Verify that your PureWhite lamp
voltage rating (120VAC or 14VAC) matches
your electrical system’s voltage requirements
before proceeding with installation.

For LPL-P1-WHT-12-S, LPL-P1-WHT-120-S, LPL-M1-WHT-12,
and LPL-M1-WHT-120
1-YEAR LIMITED WARRANTY
Product warranty
J&J Electronics, Inc. warrants the PureWhite Replacement LED
In-Ground Pool or Spa lamp (the Product) to be free from defects in
material and/or workmanship, under normal use, conditions and
service, for a period of one (1) year from the original date of
purchase. If during the warranty period, there is a defect in material
or workmanship, J&J Electronics, Inc. will repair or replace (at its
discretion) the Product under the conditions of the warranty. The
warranty covers normal consumer use of the Product. To obtain
warranty service, contact the establishment from which the Product
was purchased.
Exclusions from warranty
The PureWhite Replacement LED In-Ground Pool or Spa lamp is
designed for use in In-Ground swimming pools or spas only. If
installed for use in any other application, the warranty is void thereby
releasing J&J Electronics, Inc. from any and all claims related to its
misuse. The warranty does not cover and J&J Electronics, Inc. shall
be held harmless against any damage occurring during shipment,
damage or failure resulting from alteration, accident, theft, abuse,
negligent installation, improper service, unauthorized repairs or
where adequate care has not been taken to prevent damage to the
Product. Tampering with any internal component of this Product will
void the warranty. This warranty does not cover failure due to the
presence of water inside the niche fixture. This warranty excludes all
incidental or consequential damages except as required by state
law. This warranty gives you specific rights. You may have other
rights that vary according to the laws of your state.
STEP 2
Remove old lamp
Access the old lamp according to the original manufacturer’s light
installation manual. Remove the screws and/or loosen the clamp that holds
the face plate and lens in place. Carefully remove the lens from the light
housing. Take care not to damage the surface of the light housing body
that makes contact with the rubber gasket.
STEP 3
Inspect your light housing for signs of wear
Inspect the rubber grommet where the power cord enters the light for
excessive deterioration. Inspect the light housing, the tensioning clamp,
and face ring for warping, dents and excessive rust. Do not install
PureWhite into a light housing that appears to be worn out from prolonged
exposure to pool water or mishandling.
STEP 4
Dry the light housing and lens
Make sure the inside of the light housing and glass lens are completely
dry by wiping them down with a clean rag.
STEP 5
Install PureWhite lamp
Remove the old lamp and discard. Carefully screw the PureWhite lamp
into the socket.
STEP 6
Reassemble the light housing
Proceed by cleaning any gasket residue from the light housing body.
A clean surface is necessary for the new gasket to seat properly and
prevent leakage. Install the new gasket onto the glass lens.
WARNING! Always use a new lens gasket
whenever reassembling your light housing.
Failure to install a new lens gasket could result in water
leakage which can permanently damage the PureWhite lamp and
cause serious injury or death due to electrical shock.
Set the lens and faceplate in the light housing and re-assemble according
to the light housing manufacturer’s specification. Tighten the screws or
clamp slightly, allowing the gasket to seal evenly.
STEP 7
Submerge assembled light into the water
Once the screws or clamp are tight, submerge the assembled light housing
in the water and visually check that air bubbles are not escaping from the
gasket area. Should bubbles appear, immediately remove the light housing
from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation
by wrapping the cord around the light housing and re-attaching the light
housing to the niche assembly.
STEP 8
Check for air bubbles when light is turned ON
Reconnect power to the pool or spa light by resetting the circuit breaker to
the “ON” position. Go back to the light location and check for air bubbles
rising to the surface from the light housing for at least 10 minutes. It is
important that the lamp is turned on during this time.
If you do not see air bubbles rising to the surface at anytime during the
10-minute inspection process, the housing is holding its water tight seal
and the installation is complete. You are now ready to enjoy your new
PureWhite Replacement LED In-Ground Pool or Spa lamp.
If you do see air bubbles rising to the surface at anytime during the
inspection process, immediately remove the PureWhite lamp from the
housing, dry it completely and reset the gasket and lens. Make sure that
the PureWhite lamp and light housing are completely dry before
reassembling.
If the light housing continually leaks water after 2 or more attempts at
installation, replacement of the light housing may be necessary.
Please read the J&J Electronics “PureWhite Quick Start Guide” for further
installation advice.
Note on Figures 1-3: All figures are provided for illustration purposes only.
Refer to the original pool or spa light manufacturer’s installation manual for
further reference.
Operation
For LPL-P1-WHT-12-S, LPL-P1-WHT-120-S, LPL-M1-WHT-12, and LPL-M1-
WHT-120 PureWhite Replacement LED In-Ground Pool and Spa Lamps
Use the pool’s or spa’s current light switch to turn “ON” and “OFF” your
new PureWhite lamp.
For more information about this or other J&J Electronics lighting products, please visit www.purewhitepoollight.com. Rev. 012910-SM1
©2010 J&J Electronics, Inc. All rights reserved. PureWhite is a trademark of J&J Electronics, Inc. All registered and trademarked brands and names are the property of their respective companies.
J&J Electronics • 35 Hammond, Irvine, CA 92618 USA • 800.735.4553 • 949.455.4460 • www.jandjpoolspa.com
PAGE 2