Jolimark CP-9000K User manual

24pin Dot Matrix Printer
USER'S MANUAL
CP-9000K
JOLIMARK

* Epson is a registered trademark of S.Epson Corporation.
* LQ-2550 is a registered trademark of S.Epson Corporation.
* IBM is a registered trademark of International Business Machines Corporation.
* IBM2931 is a registered trademark of International Business Machines Corporation.
* Windows is a registered trademark of Microsoft Corporation.

USER'S MANUAL
24-pin wide-carriage
dot matrix printer
CP-9000
K

Contents
U n p a c k i n g t h e p r i n t e r. . . . . . . . 1
Q u i c k s t a rt u p.........................................2
1. Introduction
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 3
Options and expendables. . . . . . ... . . . .. .. . . .. 4
Printer description. . . . . . . . . . . . . . . . . . . .. . .. .6
2. Setting up
Installing the paper rack . . . . . . . . . . .... .. . . . . 1 0
Installing the sound seal cover . . ... ...... 1 0
Installing the ribbon cassette . ... . . . . . . . 11
Connecting the computer . . . . . . . . . .... .. . . . . 1 2
Connecting the power cord . . . . . . . ... . . . . . . 1 2
Loading the paper . . . . . . . . . . .. . . . . . . .. . . . . . 1 3
Adjusting print head position . . . .. . . ....... . . 1 5
3. Control panel and operations
Control panel and indicators . . . .. . . . . . . 1 6
Paper parking . . . . . . . . . . . . . . . . . . . . . ... . . .. . . . . . 2 0
Printing test pattern . . . . . . . . . . . . . ... . . . . . . . . 2 1
Demonstration print-out . . . . . . . .. . .... . . . . . . 2 2
Tearing off a form . . . . . . . . . . . .. . . . . . .. . . . . . . 2 2
Power-on operation summary . .. . .. . . . . . 2 3
4. Basic setup options
About basic setup options . . . . . . . ..... . . . . . . 2 4
Printing multipart paper . . . . . ......... . . . . . . . 2 6
Selecting page length
for fanfold paper. . . . . . . . . . . . . . . . . . . . . . 2 6
Selecting single sheet
paper size . . . . . . . . . . . . . . ....... . . . . . 2 7
Selecting font style . . . . . . . . . . . . . . . . . . . . . . 2 8
Selecting character spacing . . . . . . . . . . . 2 9
Enlarging/compressing print . . . . . . ...... . . . 3 0
Setting top of form position . . . . ... . . ...... . . 3 1
Loading user setup options . . . . . . . . . . . . 3 1
5. Extended setup options
About extended setup options . . ... . ... . . 3 3
P r i n t e n h a n c e m e n t
1 0 Emulation........................... ................. 3 6
1 2 Character table (Epson mode). . . . . . . . . . . 3 7
1 3 Character table (IBM mode). . . . . . . . . . . . . 3 7
1 4 National font style............ .................... 3 8
1 5 Code page............................ ............... 3 8
1 6 IBM Alternate graphic mode. . . . . .. . . . . . . 3 9
1 7 Carriage return (CR)......... .................... 3 9
1 8 Line feed (LF)................ ....................... 3 9
1 9 Line feed spacing.......... ....................... 4 0
2 0 Slashed zero.................... .................... 4 0
2 1 Set default tab stops............. ................ 4 0
2 2 Lock-in the page length..... ................... 4 0
2 3 Print quality ........................ ................ 4 1
2 4 Lock-in the font.................. ................. 4 1
2 5 Lock-in the character
spacing ............................ ................. 4 1
2 6 Lock-in the print quality...... ................... 4 1
B a r c o d e p r i n t e n h a n c e m e n t
2 7 Enable barcode print ............. .................. 4 2
2 8 Barcode type..................... ...................... 4 2
2 9 Bar code size.................. .......................... 4 4
3 0 Enlarged character size....... ...................... 4 4
3 1 Graphic Print Speed ......... ........................ 4 5
3 2 Accent character.............. ......................... 4 5
3 3 Setting of the FF code at TOF . . ....... . . . . . . . 4 5
P a p e r h a n d l i n g e n h a n c e m e n t
4 0 Set the top margin.............. ..... .................. 4 7
4 1 Set the bottom margin ..... ......................... 4 7
4 2 Set the left margin............... ...................... 4 7
4 3 Set the right margin ....... ........................... 4 8
4 4 Fanfold paper width ....... .......................... 4 8
4 5 Autoscroll delay........ ................................ 4 8
4 6 Override bottom margin ..... ...................... 4 9
4 7 Label mode....................... ....................... 4 9
4 8 Paper out detection ....... ............................ 5 0
4 9 Cut sheet feeder type ....... ......................... 5 0
5 0 Setting of the auto
scrolling position ..... ........................ 5 0
5 1 Line Feed Speed.......... ............................. 5 1
C o m m u n i c a t i o n e n h a n c e m e n t
6 0 Interface type............. .............................. 5 1
6 1 SELECT IN signal.......... ........................... 5 1
6 2 Parity bits..... ........................................... 5 1
6 3 Data length......... ..................................... 5 2
6 4 Stop bit............. ...................................... 5 2
6 5 Communication protocol . . . . ....... . . . . . . . . . 5 2
6 6 Communication speed .... .......................... 5 2
6 7 Serial error check ..... ................................ 5 3
6 8 CTS signal ............ .................................. 5 3
6 9 CD signal .......... ..................................... 5 3
7 0 DSR signal............ .................................. 5 3
7 1 Communication buffer size ............ . . . . . . . 5 4
7 2 Busy/ACK timing........ ............................. 5 4
7 3 Data latch timing........ .............................. 5 4
7 4 Setting of whether ERROR/PE
signals are output or not . . . ..... . . . 5 4
M i s c e l l a n e o u s
8 0 Print direction............ .............................. 5 5
8 1 LCD display language...... ......................... 5 5
8 2 Invert LCD display ....... ........................... 5 5
8 3 Software controlled setup . . . . . ...... . . . . . . . . 5 6
8 4 Lock the RESET key......... ........................ 5 6
8 5 Setting of ENERGY STAR . . . ...... . . . . . . . . . . 5 6
8 6 Saving user setup options . . . . . ...... . . . . . . . 5 6
8 7 Printing list of option settings . ....... . . . . 5 6

6. Setting the application software
About printer driver . . . . . . . . . . . . . . . . . . . . . . 5 7
Printer driver selection . . . . . . . . . . .. . . . . . . . . 5 7
7. Troubleshooting
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . 6 0
Troubleshooting guide . . . . . . . . . . . .. . . . . . . . 6 1
Input hexadecimal dump mode . ......6 2
8. Maintenance
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3
Lubrication. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . 6 3
Printer cover removal . . . . . . . . . . .. . . . . . . . . . 6 4
Vertical alignment mode . . . . . . . . . . . . . . 6 6
9. Bar code and enlarged
character function
B a r c o d e f u n c t i o n
Outline of bar code function......... .... . . . .. . . . 6 9
Makeup of bar code................... . . .. . . ... . . . . 6 9
Bar code command list........... .............. ....... 7 0
(1) Bar code type.......... ..................... 7 0
(2) Element width........ ...................... 7 1
(3) Bar code height.................. .........7 1
(4) Setting HRI on and off......... ......... 7 1
(5) HRI font.............. ........................ 7 2
(6) Check character.................. ........7 2
(7) Starting the bar code data sequence. .. 7 2
(8) Ending the bar code data sequence. . . 7 3
(9) Bar code data sequence......... ........ 7 3
(10) Printing density...... .................... 7 3
(11) Guide bar expansion...... ............. 7 3
(12) Start and stop characters.... ......... 7 4
(13) Barcode rotational angle...... ........ 7 4
(14) Disabling HRI of the start
and stop characters.... ......... 7 4
(15) Value input mode....... ................. 7 4
(16) Initializing the bar code mode. . . ... . 7 5
Data processing in the bar
code data sequence.... .......... 7 5
Printing bar codes.......... ................ 7 6
HRI........................ ...................... 7 6
Error processing.......... .................. 7 7
Code 128 subset transition rule. . . . . . 7 7
UPC-E conversion rule........ .......... 7 8
Calculating the check character. . . . . . 7 8
Other.............................. ..................... 8 0
Element printing.......... .......................8 0
E n l a r g e d c h a r a c t e r f u n c t i o n
Outline of enlarged
characterfunction...... ................. 8 2
Enlarged character
command list......... .................... 8 2
(1) Executing backspacing.... .................... 8 3
(2) Executing line feeding...... ................... 8 3
(3) Executing form feeding...... .................. 8 4
(4) Executing carriage return.... ................. 8 4
(5) Initializing the enlarged
character mode....... ................... 8 4
(6) Arrangement of enlarged
characters............ ..................... 8 5
(7) Cell magnification for
enlarged characters......... .................... 8 5
(8) All-character set for
enlarged characters....... ........................ 8 6
(9) Selecting an enlarged
character font............... ....................... 8 6
(10) Height expansion for
enlarged characters........... .................. 8 7
(11) HMI for enlarged characters. . . . . .. . . . . . 8 7
(12) VMI for enlarged characters. . . . . . .. . . . . . 8 8
(13) Setting and canceling the
enlarged character mode. . . . ..... . . 8 8
(14) Enlarged character cell offset. . . ....... . . 8 9
(15) Enlarged character pitch.... ................ 8 9
(16) Enlarged character quality. . . . . ......... . .9 0
(17) Enlarged character rotational angle. ....... 9 0
(18) Setting and canceling enlarged
character smoothing. ....... . 9 1
(19) Enlarged character top offset. . . . ....... . . 9 1
(20) Setting and canceling underlining
of enlarged characters. . ...... . 9 2
(21) Enlarged character
widthwise expansition.. ............... 9 2
(22) Horizontal printing position
for enlarged characters.. ......... 9 3
(23) Vertical printing position for
enlarged characters. ...... . 9 3
Enlarged character print samples. . . . ...... . 9 4

Appendices
A. Specifications
Printing specifications . . . . .... . . . . . . . . . 9 5
Parallel interface
specifications . . . . . . . . . . . . . .. . 1 0 0
Serial interface
specifications . . . . . . . . . . . . . .. . 1 0 1
Other specifications . . . ..... . . . . . . . 1 0 2
B. Control code summary
IBM mode . . . . . . . . . . . . . . . . . . . . . . .. . 1 0 3
Epson mode . . . . . . . . . . . .. . . . . . . . .. . . 1 0 9
Setup options control codes . . . . . .. . . . 1 2 2
C. Character sets. . . . . . . . . .. .. .. . . . .. . .. . . 1 2 7
D. Reverse control panel . . . . . . . . . 1 3 6

❏Power source
• Be sure to insert the power plug only in a
wall unit of the voltage designated in the
voltage selector switch and on the rating
plate on the back of the unit.
• Do not place the power cord near heat
sources or place heavy objects on it. Do not
bend or twist the power cord.
❏Foreign matter and water
• Keep your hands and personal items, such as
scarfs and ties, away from the carriage
mechanism while the printer is operating.
The carriage moves with considerable force.
• Keep the printer dry. If you accidentally
spill water on the machine, turn the power
off immediately and wipe it dry. Do not turn
the power on until the machine is
completely dry.
❏Installation environment
• The printer should be used where humidity is
low, where there is little dust, and where the
printer is not in direct sunlight.
• Avoid placing or leaning anything on top of
the printer. If you accidentally drop any
object into the machine, turn the power off
immediately, then carefully remove the
object.
• Do not twist the ribbon while installing it.
❏Operating condition
• Wait at least two seconds after turning power
off before turning it back again. The
initialization process may not be performed
correctly if this is not done.
• Do not touch the print head immediately
after printing because it is too hot.
• Never operate the printer without paper or paper properly installed.
If you use paper that is not as wide as the platen, be sure that printing does not exceed paper width.
Use software control to change the width of the print line.
• Never insert or pull out an interface cable while the power to the printer and computer is on.
• Be sure to turn off the printer before turning off a connected host computer.
Caution for use

Unpacking the printer
Check the cartons for the following items:
Unpacking the printer
Paper Rack
(See page 10)
Sound Seal Cover
(See page 10)
Printer
1
Ribbon Cassette
(See page 11)
Power Cord
(See page 12)
(Driver-CD with User’s Manual,
printer driver software)

To make your first print, follow the procedure below . For more detailed instructions on setting your
printer, please refer to the page indicated.
Self Test
Self Test
?
?
?
?
?
?
❏To set up the printer
1. Install the paper rack, the sound seal cover,
and the ribbon cassette — Pages 10 and 11.
2. Load the single cut sheet paper or fanfold
paper. Press the FF key to load the paper —
Pages 13 and 14.
❏To make a test print
1. Set the paper size of the printer in the setup
options — Pages 26 and 27.
2. Press the LF key and hold while initializing
the printer by the RESET key. Hold the LF
key until the self test starts — Page 21.
❏To connect your computer
1. With all equipment turned off, connect the
printer to your computer. Interface cable is
purchased separately — Page 12.
2. Use the extended setup options (emulation
type and communication enhancement
section) to match the specification needs
between the printer and your computer —
Pages 33 to 56.
3. Select the printer driver from your
application software — Page 57.
2
Quick startup
Quick startup

1. Introduction
Features
 Barcode Print available
1. Introduction
• 13 resident barcode type Industrial 2/5, Interleave 2/5, Codabar, Matrix 2/5, Code 11, Code 39,
Code 93, Code 128, EAN-8, EAN-13, UPC-A, UPC-E, Postnet
 Enlarged character printing
Characters can be enlarged (by up to 127 times as large x 127 times as
large) using the enlarged character command unique to this printer.
Software commands are used for control.
 Contain the 2 kind of emulations
Compatible to major printer emulations, Hewlett Packard, IBM and Epson printers.
• EPSON
• IBM LQ-2550 compatible
2391 compatible
 Wide selection of paper size
• Single cut sheet papers
• Fanfold continuous paper
• Multi-part paper
• Labeling paper
A3, A4, B4, B5, Letter, Legal
5 - 15 inch wide and 2 - 16.5 inch long paper
Original plus 8 copies (total clearance: 0.635mm (0.025”)
Label peel-proof capability
 Full option of font types and variation of character pitch
• 10 resident fonts
• 8 character pitch
Courier, Prestige, Script, OCR-A, OCR-B, Gothic, Orator, Orator-S,
Roman, and Sans Serif
10, 12, 15, 17.1, 20, 24 characters per inch (CPI), and
proportional and 1/2 proportional characters
 Enlarge/reduce your layout to fit in any paper size
• you can print the same layout of the document in different paper size.
 Easy operation
• Multiple display language for international use.
• Upside down display enables operation from the back of the printer.
 Superb compatibility and connect ability
• Communication protocols adjustable to any computer.
• Interface connections provided for parallel, RS-232C.
• Parallel and serial interface are switched automatically when "AUTO" setting is selected.
3

6
1. Introduction
Printer description
Paper Guide
Ribbon Cassette Platen
Power Switch
Paper Select Lever
(Friction Lever)
Head Adjustment Lever
Print head
Paper Bail
Sound Seal Cover
Paper Rack
Paper Cutter
Top Rear Cover
Operator Panel
Tractor Cover
Tractor Lock Lever
Printer Cover
Rear Cover

❏Operation guide sheet
The operation guide sheet helps you to operate some of the basic options on the front control panel.
You can peel the adhesive backed paper and stick it anywhere on your printer for convenience.
❏Precaution for extra-thick paper usage
Extra-thick continuous paper, especially 9-part multi-layer paper may get jammed in the printer due
to its stiffness and inflexibility. When using such paper, set the paper rack in the slant position
shown in the figure.
Tractor
Platen
Print Head Print Head
Friction Roller
Print Head
Tractor
Description
Paper width
Paper length
Ply
Total thickness
Paper weight
Single-ply
single
0.065~0.12mm
14lbs.~28lbs.
53g/m ~105g/m
22
Multiple Copies
Original+8 max.
0.635mm max.
non-carbon
Label Paper
single
0.18mm max.
125Kg max.
• Multiple Fanfold Paper
• Label Fanfold Paper
Description
Paper size
Ply
Total thickness
Paper weight
Single-ply
A3, A4, B4, B5 Letter, Legal
single
0.08~0.12mm
17lbs.~28lbs.
64g/m ~105g/m
22
Fanfold Paper
Single Sheet Paper
Push Tractor Method Friction Feed Method
• Single ply Fanfold Paper • Single Sheet Paper
5~15 inch
2~16.5 inch
7
1. Introduction

1. Introduction
 Physical dimension
24 .4" (620mm)
Paper Rack in flat position
(Continuous paper setting)
Sound Seal Cover
Paper Rack in upright position
(Single sheet setting)
Paper Rack in flat position
(Continuous paper setting)
11.6"
(295mm)
12.0"
(305mm)
Weight: 44.1 lbs. (20 kg)
8
10.2"
(260mm)
17.9"
(455mm)
15.4"
(390mm)
19.9"
(505mm)
17.1"
(435mm)

Installing the paper rack
1. Slide both paper guides to the
extreme left and right edges of the
paper rack.
2. With the two small pivots on either
side of the paper rack downward, fit
the pivots in the groove on the rear
top cover.
3. Place the paper rack in upright
position for single cut sheet paper
and lay it down for fanfold
continuous paper.
Installing the sound seal cover
1. Lay the sound seal cover upside
down on the printer.
2. Fit one of the holes of the cover to
the stud of the L-angle hinge on one
side of the printer.
3. Fit the other hole to the other stud
by pressing the L-angle hinge
inward then out through the hole.
Note
The paper guides should be placed to the outside edges
during the installation or removal of the paper rack.
Note
Make sure that both studs are out through the hole
completely, otherwise, the sound seal cover will be stuck in
place.
Rear Top Cover
12
Pivots
Groove
L-angle Hinge
10
2. Setting up
2. Setting up

Installing the ribbon cassette
Turn OFF the printer's power and remove the used ribbon cassette, if necessary, by pulling straight
upward.
1. Open the printer cover.
2. Manually move the print head to the extreme right side of the printer for easy installation of the
ribbon. Do not try to move the print head if the power is on.
3. Turn the ribbon feed knob in the direction of the arrow on the knob to remove any slack in the
ribbon.
4. Place the ribbon cassette on the left and right cassette holders, such that the ribbon rests on the
ribbon guide. Check to be sure that the ribbon drive shaft on the left cassette holder is inserted in the
hole on the bottom of the ribbon cassette.
5. Turn the ribbon feed knob in the direction of the arrow on the knob to remove any slack in the
ribbon.
6. Replace the front printer cover and set the head adjustment lever to the proper position for the best
print quality.
CAUTION
Do not touch the print head if the printer has been running for a long time. Wait
until the print head is cooled off.
Cassette Holders
Ribbon Guide Ribbon Mask
Cassette Holder
Remove any slack from ribbon
Ribbon Feed Knob
11
2. Setting up

2. Setting up
Connecting the computer
The printer has a parallel interface connector (Centronics) and a serial interface connector (RS232C).
Before you connect an interface cable to your computer, you need to know what type of printer
driver is supported by your software applications and what type of connector is needed to attach the
printer to the computer.
 Parallel Interface
36-pin plug
CAUTION
 Serial Interface
25-pin plug
220-240V 120V
CAUTION
220-240V 120V
13
13
25
1
14
1
Connecting the power cord
T5A 250V
T2.5A250V(ForEuropean)
25 14
Check the power requirement printed on the rating plate on the rear of the printer before attaching
the power cord and turning on the printer.
N
o
t
e
12

Loading the paper
❏Fanfold continuous paper
1. Move the paper select lever toward the front of the printer to set
the fanfold paper setting.
2. Set the print head adjustment lever . In general, position 1 is
used for one-part paper. (See page 15)
3. Remove the rear cover of the printer or open the rear cover to
lock the cover in the open position.
4. Release the tractor lock levers (upward), and move the right tractor to
the marked position as shown in the figure, and lock it in place.
5. Open both tractor covers and place the fanfold paper so that the tractor pins are aligned with the
holes in the paper. Carefully close both tractor covers.
6. After the paper is properly installed, re-adjust the left tractor to a position to keep the paper taut (but
not too taut) between the left and right tractors.
7. To load the paper, press the PARK key or FF key on the front panel. The fanfold paper is fed to the
top-of-form position 14/60 inch (6mm)below the top edge of the paper. The top-of-form position can
be adjusted from 0/60 inch to 480/60 inches (8 inches = 203mm) in the basic setup options on page
31.
8. The paper bail automatically lowers to press the paper against the platen when the leading edge of
the paper feeds more than one inch onto the platen.
1
2
Rear Cover
Left Tractor Cover
Not Too Taut !!
Left Margin Marker
Tractor Cover
Tractor Lock Lever
Right Tractor
Releasing direction
5
4
3
5
13
2. Setting up
Caution
Be careful not to catch your finger when closing the tractor covers.

❏Single sheet paper
1. Move the paper select lever toward the rear of the printer to the single
sheet setting.
2. Set the print head adjustment lever . In general, position 1 is used
for one-part paper. See page 15.
3. Raise the paper rack to the vertical position and adjust the left
paper guide to the proper position for the size of the paper being
used.
4. Place single sheet paper against the paper rack and let it slide behind the platen.
5. Adjust the right paper guide so that it comfortably holds the paper in between the two paper
guides.
6. Press the PARK key or FF key to load the single sheet paper to the top-of-form position 14/60 inch
(6mm) below the top edge of the paper. The top-of-form position can be adjusted from 0/60 inch to
480/60 inches (8 inches = 203mm) by using the front panel controls in the basic setup options on
page 30.
7. The paper bail automatically lowers to press the paper against the platen when the leading edge of
the paper feeds more than one inch onto the platen.
Note
If the paper is not loaded on the proper mark, the printer
may not detect the paper and will issue PAPER ERROR.
Note
If the paper is not completely fed in, slightly push the paper downward. If it is still not fed in,
look in the TROUBLESHOOTING section.
Notes
1.Extension Arm
The extension arm is used to keep large size (Legal, B4) single sheets from falling behind the
paper rack. When using the extension arm, pull the arm until it clicks and locks in place.
2.TEAR OFF keys are invalid with single sheet paper.
1
2
A3 B4
Paper Size Marker
Left Paper Guide
Extension Arm
Right Paper Guide
3
4
14
2. Setting up

❏Paper alignment
Current print line location
The current printing line (DDD...) is the third line down from the top of the ribbon guide (line
spacing is 1/6 line: 6 LPI).
Adjusting the print head position
The head adjustment is used to obtain the best print quality possible for the specific paper
being used. The print head position can be adjusted to accommodate printing on single and
multipart forms. When using multipart forms, move the print head adjustment lever toward the
front of the printer to widen the gap between the print head and the platen.
In general, position 1 is used for one-part paper. Moving the head adjustment lever one notch
adjusts the print head gap an amount corresponding to the addition of one more paper part.
Re-adjustment of the lever may be required depending on the quality of the actual printout:
• If the ribbon smears on the paper, the gap is too narrow.
• If the printed image is too light to read, the gap is too wide.
D
AAAAAAAA
BBBB
CCCC
DDD
0.5
Ribbon Guide
Head Adjustment Lever:
Move toward the front of
the printer for thicker paper
1 part-paper: 2nd click
5 part-paper: 8th click
9 part-paper: 13th click
(This scale is the suggested
number of sheets
for non-carbon part-paper.)
1
5
9
1
5
9
Notes
1.The print head adjustment lever should be set before loading the paper to avoid
paper jams.
2.If the printed image on the last copy of a multipart form is too light to read, set the
MULTIPART mode in the basic setup options (see page 26). This will increase the
striking intensity on multipart forms.
15
2. Setting up

Control panel and indicators
Standard Panel
Alternate up-side down reverse panel
Note: The alternate reverse panel installation instruction is described in Appendix D.
❏Indicators
•Display window Liquid Crystal Display (LCD)
Displays status and errors during operation and menus in the setup options.
PARK
BIN
TOF SET
QUALITY
ENTER
SETUP M.RLF
LF
M.LF FF
TEAR OFFRLF ON LINE
P.OUT
ON LINE
POWER
EXIT
ALT
L C D
RESET
TOF SET
BIN
PARK
ENTER
ALT SETUP
M.RLF
LF M.LFFF
TEAR OFF RLFON LINE
P.OUT
ON LINE
POWER
EXIT
QUALITY
L C D
RESET
The followings are some examples of the display messages.
If the printer is in the offline mode, the following appears on the display.
Status message
This indicates that the printer is in offline and paper out status.
P.OUT FANFOLD
Warning message
This indicates that the printer cover is open. Close the cover to
resume the operation .
COVER OPEN
Status message for fanfold continuous paper
This column indicates the page length; and the paper widlh.
This indicates the type of paper selected is fanfold continuous
paper.
FANFOLD 11 15
Status message for single sheets paper
This indicates a paper size; B5 through A3 depending on the
designated paper size (default A4) selected in the setup options.
This indicates the type of paper selected is single sheet paper.
MANUAL, BIN 1, BIN 2, BIN 1+2
MANUAL: A4 P
16
3. Control panel and operations
3. Control panel and operations