Kaba Mas LA GARD SMARTLINC Operation instructions

SMARTLINC
Multiple Lock System
user operating instructions
CHANGING YOUR CODE
ALWAYS PERFORM THIS OPERATION WITH
THE DOOR OPEN
If you have access to multiple locks, you must
repeat this procedure on each lock you have
access to.
1. Press any key to power up SMARTLINC.
 • Displaywillshoweither“ENTERCOMBO”
  or“SELECTLOCK”whentwoormorelocks
  areinstalled.
2.Selectlockiftwoormorelocksareinstalled.
3.Enter“zero”sixtimes
4.Enterexistingsix(6)digitcodeonetime(and
 inserteKeyII,ifset-up).
5.EnterNEWsix(6)digitcodetwotimes(and
 inserteKeyII,ifset-up,after2ndentry).
 • IfavalidcodeisenteredtheLCDwilldisplay
  “USERUPDATED”
6.Ifamistakeismadewaitthirty(30)seconds
 andrepeatsteps1-4.
 • OldCodewillremainvalidifamistakeismade.
 • Incaseofamistake,LCDwilldisplay“ERROR!”
7.Testlockoperationseveraltimesbeforeclosingthedoor.
CHANGING YOUR BATTERY
1.Removeblackplasticbatterycompartmentcover(located
 atthebottomofthekeypad)bygentlypullingdownwardon
 itshandle.
2.Allowthebatteryanditsattachedleadstodropdownand
 outofthebatterycompartment.Ifitdoesnotdrop,gently
 pullonthebatteryuntilitdoes.
3.Removetheconnectorbyunsnappingitfromthetwo
 terminalsonthetopofthebattery.
Never Pull on the Battery Leads
4.Connectanew9-VoltAlkalinebatterytothebatteryclip.
5.Pushthebatteryandtheleadscompletelyupintothe
 batterycompartment.
6.Installthebatterycoverbyplacingone
 sideofthecoverinpositionandthen
 pressingtheothersideintopositionwith
 yournger.
WARNING: The port for the eKEYII is a data
port only. Connecting power to this port will
damage the system.
NOTE:Thissystemcomesequippedwithan
AuxiliaryPowerBox(APB).Ifprimarypoweris
lost,theAPBwillmaintainpowertotheaudit
clockfor90hours.THE UNIT WILL NOT
FUNCTION UNTIL PRIMARY HAS BEEN
RE-ESTABLISHED, i.e. batteries have been
replaced or A/C power has been connected.
AVAILABLE FEATURES
USER CODE
• OpenLock
• ChangeCode
• SetImmediateTimeLock,ifenabled
• TimeDelayExtension,ifenabled
• TemporaryTimeLock,ifenabled
MULTIPLE LOCKS
• UptoFive
TIME DELAY
• Programmableoneachlock
  - DelayPeriod:1-99minutes
  - OpenPeriod:1-19minutes
• TwoTimeDelaysCanRunAtOnce
DUAL CODE
• TwoCodesrequiredtoopen
eKEYII MODE
• Programmableoneachlock;requirescodeandkeyforentry
• AvailabletoManagerandUsersonly,ifenabled
WRONG TRY PENALTY
• Four(4)consecutiveinvalidcodesinitiatesveminutedelayperiod
LOW BATTERY WARNING
• Repeatedaudioandvisualsignal(LCDreadoutandrepeated
 beeping)duringopeningindicatesbatterylow
AUDIO AND VISUAL SIGNAL
• Doublesignal(LCDreadoutandunitbeeps)indicatesentryisvalid
 oraccepted
• Triplesignalindicatesinvalidornotaccepted
TIME LOCK
Ifenabled,seeManagerInstructionsforoperation.
©copyright2006 (P/N)12-245v3•9/08 Kaba Mas LLC
page1of2
OptionaleKeyII
P/N40169
SELECT LOCK
XX
ENTER COMBO
X-X-X-X-X-X
OLD CODE
X-X-X-X-X-X
NEW CODE
X-X-X-X-X-X
CONFIRM NEW
X-X-X-X-X-X
USER
UPDATED
ERROR!
Please note: If using the SMARTLINC with the eKEYII feature, remove the key after each insertion to begin the next step. If the eKEYII is
left in the key port, the SMARTLINC will not respond to any key stroke.

©copyright2006 (P/N)12-245v3•9/08 Kaba Mas LLC
page2of2
OPENING THE LOCK(WITHOUTTIMEDELAY)
1. Press any key to power up SMARTLINC.
 • Displaywillshoweither“ENTERCOMBO”or“SELECTLOCK”whentwoormorelocksareinstalled.
2.Selectlockiftwoormorelocksareinstalled.
3.Enteravalid6(six)digitcode(andinserttheeKeyII,ifset-up)
 • IfavalidcodeisenteredtheLCDwilldisplay“OPEN”
4.OpentheDoorwithin3seconds.
 • Beforepower-off,LCDwilldisplaycurrentdateandtime.
• InvalidcodewillpromptLCDtodisplay“NOTVALIDUSER”
• Displaywillpower-offafter30secondsofnon-operation.
OPENING THE LOCK (WITHTIMEDELAY)
1. Press any key to power up SMARTLINC.
 • Displaywillshoweither“ENTERCOMBO”or“SELECTLOCK”whentwoormore,locksareinstalled.
2.Selectlockiftwoormorelocksareinstalled.
3.Enteravalid6(six)digitcode(andinserteKeyII,ifsetup)
 • IfTimeDelayhasbeensettheLCDwillshow“TIMEDELAY”andthecountingtime.
 • Countingisupdatedeverysecond,ifdisplayed.
 • Press“0”toabortTimeDelay DELAYABORTED!
 • AfterTimeDelayhaselapsed,thedisplaywillshow“mm:ss”(openwindowcountingtime).Unitwillbeepevery
  ve(5)secondsduringcountdown.
4.Enteravalidcode(andinserteKeyII,ifsetup)toopen.
 • IfavalidcodeisenteredtheLCDwilldisplay“OPEN”
5.Openthedoorwithin3seconds.
 • InvalidcodewillpromptLCDtodisplay“NOTVALIDUSER”
• Displaywillpower-offafter30secondsofnon-operation.
• IfusingtheTimeDelayOverride(USER#9),enterUSERcodeforUSER#9andinserteKeyII.
NOTE: To open a 2nd lock while one is in Time Delay, press the “P” key and select that lock number, then follow opening procedure
above. During Time Delay only the “P” and the zero key are active.
OPENING THE LOCK(WITHDUALCODEANDTIMEDELAY)
1. Press any key to power up SMARTLINC.
 • Displaywillshoweither“ENTERCOMBO”or“SELECTLOCK”whentwoormorelocksareinstalled.
2.Selectlockiftwoormorelocksareinstalled.
3.Enteravalid6(six)digitcode(andinserteKeyII,ifsetup)
 • IfTimeDelayhasbeensettheLCDwillshow“TIMEDELAY”andthecountingtime.
 • Countingisupdatedeverysecond,ifdisplayed.
 • Press“0”toabortTimeDelay DELAYABORTED!
• AfterTimeDelayhaselapsed,thedisplaywillshow“mm:ss”(openwindowcountingtime).
4.Enteravalid6(six)digitcode(andinserteKeyII,ifsetup)
5.Entera2ndvalid6(six)digitcode(andinserteKeyII,ifsetup)
 • IfavalidcodeisenteredtheLCDwilldisplay“OPEN”
 • IftheOverrideUser(#9)isinstalledwithDualCode,User#9mustentertheircode(andinserteKeyII,
  ifsetup)rst.
6.Openthedoorwithin3seconds.
• InvalidcodewillpromptLCDtodisplay“NOTVALIDUSER”
• Displaywillpower-offafter30secondsofnon-operation.
NOTE: To open a 2nd lock while one is in Time Delay, press the “P” key and select that lock number then follow opening
procedure above.
OPENING THE LOCK (WITHDUALCODE-NOTIMEDELAY)
1. Press any key to power up SMARTLINC.
 • Displaywillshoweither“ENTERCOMBO”or“SELECTLOCK”whentwoormorelocksareinstalled.
2.Selectlockiftwoormorelocksareinstalled.
3.Enteravalid6(six)digitcode(andinserteKeyII,ifsetup)
4.Entera2ndvalid6(six)digitcode(andinserteKeyII,ifsetup)
 • IfavalidcodeisenteredtheLCDwilldisplay“OPEN”
5.Openthedoorwithin3seconds.
 • Beforepower-off,LCDwilldisplaycurrentdateandtime.
• InvalidcodewillpromptLCDtodisplay“NOTVALIDUSER”.
• Displaywillpower-offafter30secondsofnon-operation.
SELECT LOCK
XX
SELECT LOCK
XX
SELECT LOCK
XX
SELECT LOCK
XX
ENTER COMBO
X-X-X-X-X-X
ENTER COMBO
X-X-X-X-X-X
ENTER COMBO
X-X-X-X-X-X
ENTER COMBO
X-X-X-X-X-X
OPEN!
TIME DELAY
14:31
TIME DELAY
14:31
2nd CODE
X-X-X-X-X-X
NOT VALID
USER!
03:51
X-X-X-X-X-X
03:51
X-X-X-X-X-X
2nd CODE
X-X-X-X-X-X
OPEN!
OPEN!
OPEN!
NOT VALID
USER!