Kaba Confidant RFID Kit 2 User manual

INSTALLATION GUIDE
Confidant RFID Kit 2 & Kit 3
(European Mortise Lock Case)
Rose Mount & Back Plate

3
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
IMPORTANT: Wear Safety glasses before starting the installation process.
Confidant RFIDTM Installation Instructions (Kit 2 & Kit 3)
Installation Steps:
Disclaimer ......................................................................4
1. Tools .......................................................................4
2. Inventory (Use "No Key Override" kit if no cylinder is required) ...........................5
Rose Mount (Key Override) .........................................................5
Rose Mount (No Key Override) ......................................................6
Back Plate Mount (Key Override) ....................................................7
Back Plate Mount (No Key Override) .................................................8
3. Install Spindle ................................................................9
4. Install Outside Lever..........................................................10
5. Align Posts with Mortise.............................................................11
6A. Adjust Handing .....................................................................12
6B. Prepare Inside Housing..............................................................12
7. Install Lock on Door ..........................................................13
Back Plate Mount (Key Override) ...................................................13
Rose Mount (Key Override) ........................................................13
Back Plate Mount (No Key Override) ................................................14
Rose Mount (No Key Override) .....................................................14
8. Install Inside Trim Cover .............................................................15
9. Plug Battery Holder ..........................................................15
10. Test Lock Functionality .......................................................16
11. Program Lock - With Jack Cable................................................16
12. Install Battery Door ..........................................................17
13. Maintenance (applicable only to Kit 3 lock certified EN 179 with BMH 801 lock case) ....17
14. Emergency exit devices EN 179
(applicable only to kit 3 lock certified EN 179 with BMH 801 lock case).....................18
15. EN 179 certificate (applicable only to kit 3 lock certified EN 179 with BMH 801 lock case) .....18
Annex A. Install Outside Housing with Gasket and Cylinder Shield .......................19
Annex B. Remove Battery Holder ..................................................19
Annex C. Install Bluetooth and Messenger module ....................................20
Annex D. Remove cover of Bluetooth and Messenger module ...........................22
Drilling templates are availbale on the support site kabalodgingsupport.com.
Model: Confidant RFID
IC: 4652A-CRFID
FCCID: Q8SCONFIDANT-RFID
Regulatory Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interfer-
ence, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Made in Canada
©2015 Kaba Lodging Systems. All trademarks and registered trademarks are the property of their respective owners.

4Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
Disclaimer
1- Tools
A - Screw Driver Small Flat
B - Screw Driver Phillips #1 & #2
C - Screw Driver Torx T-20
D - Hexagonal Key 3 mm
E - 25mm / 24mm / 19mm / 12mm / 10mm Drill Bit
F - Needle Nose Pliers
A B C D
E F
Important: Carefully inspect windows, doorframe, door, etc. to ensure that the recommended procedures will not cause dam-
age. Kaba standard warranty does not cover damages caused by installation.
Refer to drilling templates for the hole to drill in the doors.
Caution: Wear safety glasses when making the holes.
Respect applicable building codes regarding handle height.

5
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
Inside Trim
with Thumbturn
Inside Trim
without Thumbturn
2- INVENTORY - Rose Mount (Key Override)
Inventory Kit
3rd Party (Mortise & Cylinder)
Warning:
Install only on
a mortise with
anti-panic and
an auxiliary dead
latch (Anti-Pick
system)
A-Without Key Cylinder
B-With Key Cylinder
A B
*
*This one may be
attached to lock

6Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
Inside Trim
with Thumbturn
Inside Trim
without Thumbturn
Warning:
Install only on
a mortise with
anti-panic and
an auxiliary
dead latch
(Anti-Pick sys-
tem)
2- INVENTORY - Rose Mount (No Key Override)
To use if no cylinder is required
Inventory Kit
3rd Party (Mortise)
*
*Post may be
attached to lock

7
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
2- INVENTORY - Back Plate Mount (Key Override)
Inventory Kit
3rd Party (Mortise & Cylinder)
Warning:
Install only on
a mortise with
anti-panic and
an auxiliary
dead latch (An-
ti-Pick system)
Inside Trim
with Thumbturn
Inside Trim
without Thumbturn
A-Without Key Cylinder
B-With Key Cylinder
A B
*
*Post may be
attached to lock

8Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
2- INVENTORY - Back Plate Mount (No Key Override)
To use if no cylinder is required
Inventory Kit
3rd Party (Mortise)
Warning:
Install only on
a mortise with
anti-panic and
an auxiliary dead
latch (Anti-Pick
system)
Inside Trim
with Thumbturn
Inside Trim
without Thumbturn
*
*Post may be
attached to lock

9
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
3- INSTALL SPINDLE
1- Check Handing: Adjust for Right Hand (RH) or Left Hand (LH) 2- Insert Spindle
3- Attach and Clamp Spindle Clip to Spindle as shown.
RH LH
Ensure legs are firmly clamped
against the spindle

10 Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
4- INSTALL OUTSIDE LEVER
Left Hand
Right Hand
1 *
1 *
2
2
* N.B. Hold down the outside lever against the outside housing while tightening the lever set screw.

11
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
5- ALIGN POSTS WITH MORTISE (Rose Mount Only)
Ensure Mortise lock case includes an anti-pick and anti-panic function

12 Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
6B- PREPARE INSIDE HOUSING
6A- ADJUST HANDING
Inside Right Hand Housing Inside Left Hand Housing
Handing LH to RH
Handing RH to LH
1- Remove
1- Remove
2- Rotate 180˙
2- Rotate 180˙
3- Assemble
3- Assemble

13
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
7- INSTALL LOCK ON DOOR - Back Plate Mount (Key Override)
7- INSTALL LOCK ON DOOR - Rose Mount (Key Override)
*
C
Screw M5
(5mm)
Screw M5
(5mm)
Screw M4
(4mm)
A
B
A
B
A
*
*
C
D
D
IMPORTANT
See Annex A for
Exterior Applications
See Annex A for
Exterior Applications
3mm to 13mm
3mm to 13mm
• A, B, C and D required
for security grade
• A always required
• C recommended
IMPORTANT: After connecting
all cables, make sure all excess
cables are pushed inside the
hole(s) in the door.
IMPORTANT: After
connecting all cables,
make sure all excess
cables are pushed
inside the hole(s) in
the door.
For Kit 3 lock certified EN 179 with BMH 801 lock case, please refer
to the following before installing the lock:
- Installation and maintenace manual for BMH-panic door locks
- Instructions for the use of BMH locks and hinges
For Kit 3 lock certified EN 179 with BMH 801 lock case, please refer
to the following before installing the lock:
- Installation and maintenace manual for BMH-panic door locks
- Instructions for the use of BMH locks and hinges *
*Post may be
attached to lock
To tighten set
screw for DIN
certified locks
IMPORTANT:
For DIN lock
install this plate
IMPORTANT:
For DIN lock
install this plate
To tighten set
screw for DIN
certified locks
*Post may be
attached to lock

14 Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
See Annex A for
Exterior Applications
See Annex A for
Exterior Applications
7- INSTALL LOCK ON DOOR - Back Plate Mount (No Key Override)
7- INSTALL LOCK ON DOOR - Rose Mount (No Key Override)
Screw M5
(5mm)
Screw M4
(4mm)
Screw M4
(4mm)
Optional**
IMPORTANT: After connecting
all cables, make sure all excess
cables are pushed inside the
hole(s) in the door.
IMPORTANT: After connecting all
cables, make sure all excess cables are
pushed inside the hole(s) in the door.
**Recommended for more security
For Kit 3 lock certified EN 179 with BMH 801 lock case, please refer
to the following before installing the lock:
- Installation and maintenace manual for BMH-panic door locks
- Instructions for the use of BMH locks and hinges
For Kit 3 lock certified EN 179 with BMH 801 lock case, please refer
to the following before installing the lock:
- Installation and maintenace manual for BMH-panic door locks
- Instructions for the use of BMH locks and hinges
*
*
**
*Post may be
attached to lock
To tighten set
screw for DIN
certified locks
To tighten
set screw
for DIN
certified
locks
*Post may be
attached to lock

15
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
8- INSTALL INSIDE TRIM COVER
Thumbturn must be vertical
(if applicable)
1
2
3

16 Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
9- PLUG BATTERY HOLDER
✗
✗✓
✓
10- TEST LOCK FUNCTIONALITY (To be done while door is still open)
Make Sure Room Door is Open
A - Present Test Keycard
B - Check Green & Red Lights Flash
C - Rotate Outside Lever to Check Bolt Retraction
D - Release Outside Lever, Should Move Freely
E - Rotate Inside Lever to Check Bolt Retraction
F - Check Bolt Projection from Thumbturn & Key
N.B.: Ensure the battery holder is pushed up
fully and is not impeding the cylinder.
11- PROGRAM LOCK - With Jack Cable

17
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
12- INSTALL BATTERY DOOR
13- Maintenance (applicable only to Kit 3 lock certified EN 179 with BMH 801 lock case)
Refer to the following:
- Installation and maintenace manual for BMH-panic door locks
- Instructions for the use of BMH locks and hinges
* Warning: For security reasons, lock must be programmed BEFORE installing the battery door. Every time the battery door is removed pass an emergency card or connect lock to Kaba
handheld programming device to reset the tamper alarm. Audit information is not affected.
A
C
B
D
* WARNING

18 Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
15- EN 179 certificate
(applicable only to kit 3 lock certified EN 179 with BMH 801 lock case)
The EN 179 identification label on the lock can be find in the location shown below
underneath the battery holder. Refer to annex B for instructions how to remove the
battery holder.
For declaration of performance,
please visit www.kabalodgingsupport.com
14- Emergency exit device
(applicable only to lock kit 3 EN 179 certified with BMH 801 lock case)
A pictogram for emergency exit device has to be installed on the door on the inner side
just above the lock as shown below.

19
Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
Annex A • Install Outside Housing - with Gasket and Cylinder Shield
(Exterior and Ocean Front Versions)
Annex B • Remove Battery Holder
A
C
B
D
Unscrew
Unclip Battery Holder
Remove Door
Remove Battery Holder
Model with Key Cylinder only

20 Confidant RFID Kit 2 & Kit 3 Installation Guide - PK3649_T_04_16
13-A 3-B2
5
4
Annex C • Install Bluetooth and Messenger module
See annex D for instructions of how to remove the cover from the module.