Kargo Master 40813 User manual

40813 Parts List
Tube Assembly
Item -016
QTY 1
E-6000
E-6000
QTY 1
Pad Bracket
Item -026
QTY 1
Lock Box Assembly
Item -002
QTY 1
Support Angle
Item -014
QTY 1
Side Tube Assembly
Item -012
Qty 1
Handle
Item -002
QTY 1
Clamp Pads
Item -034
QTY 2
Bracket Plate
Item -015
QTY 1

7RROV1HHGHG
*+!,
- 
.- 
-"/"0
.-"/"0
&

1"#0%"#
(

)-23"/0
(*
&RPSRQHQW3DFN
1'&3' 456'7*($(8$*,"1%*79,$7(9,9: ;
+DUGZDUH/LVW
+DUGZDUH3DFN
:;
(
(-*%#
:;
3
(-*33
:;
3
(-*1/0
:;
8
)-1/0
:#;

)-(-$&
:0;

)-33
:@;

)-(-$
'%#
XXXXXXX:;

)--
'%#
:B;

)-3C3
(w)
Qty 2 -
3/8-16 x 3/4 Carriage Bolt
(a)
Qty 1 -
3/8-16 x 1 Carriage Bolt
(z)
Qty 1 -
5/16 Contour Washer

DIAGRAM 1b
(Existing 40853)
Curb Side
STEP 2
Install support angle (-014) per [DIAGRAM 1c] using 2 each 3/8 x 1 carriage bolts
(a), 2 each 3/8 flat washers and 2 each 3/8 nylock nuts (c). Install into third square
hole from the end of cross bow (-001).
Side Tube
(-012)
(v)
(h)
Existing Cross Bow
(-001)
Third Hole
(Existing 40853)
Curb Side
DIAGRAM 1c
Support Angle
(-014)
(a)
(b)
(c)
STEP 1

AV
Flange Side
Bracket Plate
(-015)
Bushing
(-013)
BB
STEP 4
Install bracket plate
(-015) with the
flange facing
outward onto tube
assemby (-016)
as shown.
Bracket
Plate (-015)
Tube Assembly
(-016)
E6000
CE
DIAGRAM 2b
Bushing
(-013)
Flange Side
Cross Bow
(-001)
Support Angle
(-014)
DIAGRAM 2a
CF
(v)
(k)
(h)
Bracket Plate
(-015)
Tube
Assembly
(-016)
Angle Support
(-014)
Cross Bow
(-001)
Side Tube
(-012)
STEP 3
Next, insert bushing (-013) into support angle (-014) flange side in per [DIAGRAM 2a].
Next, insert bushing (-013) into bracket plate(-015) as shown in [DIAGRAM 2b].
STEP 5
Now install the end of tube
assembly (-016) into the bushing
on the support angle (-014).
Match up the holes in the bracket
plate (-015) to the holes in the side
tube (-012 ) and insert 2 each
carriage bolts (v), 2 each 5/16 flat
washers (k) and 2 each 5/16 nylock
nuts (h). Run a bead around heads
of bolts with E6000.

E6000
CH
Side Tube
(-012)
Handle
(-002)
Support Angle
(-014)
(g)
(-038)
(-038)
(h)
CJ
Lock Box Assembly
(-002)
Side Tube
(-012)
Angle Support
(-014)
CU
Existing 40853 Parts
Rear
View
DIAGRAM 4
Tube Assembly
(-016)
Existing Cross Bow
(-001)
DIAGRAM 3
(u)
(w)
STEP 6
Next, install handle (-002) to the end of tube assembly (-016) using 1 each
5/16 x 2 3/4 hex bolt (g), 2 each nylon washers (-038), 2 each 5/16 flat washers
(k), 1 each 5/16 nylock nut (h). Note: insert washers (-038 ) over and under
handle tube (-002) per [DIAGRAM 3] . Tighten so handle rotates freely.
STEP 7

CV
Clamp Pads
(-034)
Tube Assembly
(-020)
(b)
(c)
Pad Bracket
(-026)
STEP 9
Now install ladder into desired position with ladder rung firmly against the
clamp pads. Now adjust front pad bracket (-026) firmly against rung. It may
be necessary to move pad bracket (-026) to align with one of the two square
holes in the bow. Note: position pad bracket (-026) so adequate pressure is
applied to ladder rung when rotating handle (-002). Ladder should be
clamped firm with no movement when handle is in lock position. Tighten all
hardware.
DIAGRAM 7a
Handle
(-002)
Pad Bracket
(-026)
(Existing 40853)
Curb Side
DIAGRAM 7
Pad Bracket
(-026)
(a)
(b)
(c)
STEP 8
Install pad bracket (-026) using 1 each 3/8 x 1
carriage bolt (m), 1each 3/8 flat washer (b), 1
each 3/8 nylock nut (c) shown in [DIAGRAM 7] .
Do not tighten for later adjustment.
Now install the clamp pads (-034) to pad
bracket (-026) and tube assembly (-020) per
[DIAGRAM 7a] using 2 each 3/8 washers (b)
and 2 each 3/8 nylock nuts (c). Do not tighten.