Kemppi KempGouge ARC 800 User manual

Operating manual • English
Käyttöohje • Suomi
Bruksanvisning • Svenska
Bruksanvisning • Norsk
Brugsanvisning • Dansk
Gebrauchsanweisung • Deutsch
Gebruiksaanwijzing • Nederlands
Manuel d’utilisation • Français
Manual de instrucciones • Español
Instrukcja obsługi • Polski
Инструкции по эксплуатации • По-русски
EN
FI
SV
NO
DA
DE
NL
FR
ES
PL
RU
KempGouge ARC 800

OPERATING MANUAL
English
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
CONTENTS
1. PREFACE........................................................................................................................................................3
1.1 General.................................................................................................................................................................3
1.2 General about carbon-arc gouging................................................................................................3
1.3 Introduction .....................................................................................................................................................4
1.3.1 Power source..........................................................................................................................................4
1.3.2 Control panel .........................................................................................................................................5
2. INSTALLATION......................................................................................................................................5
2.1 Positioning of the machine...................................................................................................................5
2.2 Connection to mains .................................................................................................................................6
2.3 Distribution network .................................................................................................................................6
2.4 Gouging and earthing cables..............................................................................................................7
2.4.1 Connecting the gouging cable .......................................................................................................7
2.4.2 Connecting the earthing cable .......................................................................................................7
3. USE .......................................................................................................................................................................7
3.1 Before you start..............................................................................................................................................7
3.2 How to use the remote control..........................................................................................................8
3.3 Starting of the power source...............................................................................................................8
3.3.1 Automatic function test..................................................................................................................... 8
3.3.2 Front panel indicators.........................................................................................................................8
3.4 Control panel functions...........................................................................................................................8
3.4.1 Adjusting the gouging current .......................................................................................................8
3.4.2 Actual gouging current and voltage display..............................................................................9
3.4.3 Restoring factory settings.................................................................................................................9
3.5 Techniques for carbon-arc gouging...............................................................................................9
4. TROUBLESHOOTING.....................................................................................................................9
4.1 Overload (yellow indicator lit).............................................................................................................9
4.2 Control cable connector fuse...........................................................................................................10
4.3 Cable network with over voltage or under voltage......................................................... 10
4.4 Missing phase in the electric network.......................................................................................10
4.5 Machine error codes ...............................................................................................................................10
5. SERVICE.......................................................................................................................................................11
5.1 Cables.................................................................................................................................................................11
5.2 Power source ................................................................................................................................................11
5.3 Regular maintenance.............................................................................................................................11
5.4 Disposal of the machine....................................................................................................................... 11
6. ORDERING NUMBERS...............................................................................................................12
7. TECHNICAL SPECIFICATIONS........................................................................................ 12
2
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
1. PREFACE
1.1 GENERAL
Congratulations on your choice of KempGouge™ ARC 800 carbon arc gouging solution. Used
correctly, Kemppi products can signicantly increase the productivity of your welding, and
provide years of economical service.
This operating manual contains important information on the use, maintenance and safety of
your Kemppi product. The technical specications of the equipment can be found at the end
of the manual.
Please read the manual carefully before using the equipment for the rst time. For your
own safety and that of your working environment, pay particular attention to the safety
instructions in the manual.
For more information on Kemppi products, contact Kemppi Oy, consult an authorised Kemppi
dealer, or visit the Kemppi web site at www.kemppi.com.
The specications presented in this manual are subject to change without prior notice.
Important notes
Items in the manual that require particular attention in order to minimise damage and
personal harm are indicated with the ’NOTE!’ notation. Read these sections carefully and follow
their instructions.
Disclaimer
While every eort has been made to ensure that the information contained in this guide
is accurate and complete, no liability can be accepted for any errors or omissions. Kemppi
reserves the right to change the specication of the product described at any time without
prior notice. Do not copy, record, reproduce or transmit the contents of this guide without
prior permission from Kemppi.
1.2 GENERAL ABOUT CARBONARC GOUGING
Carbon-arc gouging refers to a method where metal is removed by melting it with a welding
arc and blowing the melted metal away with compressed air.
Carbon-arc gouging can be used with the majority of metals, such as steel, stainless steel, cast
iron, nickel, copper, magnesium and aluminium.
The equipment used in carbon-arc gouging comprises the gouging power source, a carbon
holder and its cables, and the gouging carbon, which can be round or at. Also a sucient
compressed air supply must be available.
A round gouging carbon can be used in:
• opening a root weld
• opening faulty welds and cracks
• manufacturing welding grooves
• cutting metal
• making holes
A at carbon can be used in:
• arc grading of surface errors in roller slabs
• cleaning steel casts
• opening faulty casts
• arc grading of weld caps
3
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
1.3 INTRODUCTION
KempGouge™ ARC 800 is a solution for all arc gouging needs. An 800-A power source with
a control panel is included in the package. The gouging carbon and carbon holder must be
acquired separately.
1.3.1 Power source
6,3 A
6,3 A
A4
A2
A5
A6
A7
A8
A9
A1
A3
A10
A10
A11
A9
Front view Rear view
A1 Control panel
A2 Main switch
A3 Signal light (I/O)
A4 Thermal warning light
A5 Gouging cable connection
A6 Earth connection
A7 Remote control and service connection
A8 Connection cable input
A9 Fuse for control cable connection (6.3 A slow)
A10 Fan grill
A11 Accessory box
4
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
1.3.2 Control panel
P1 P2 P3
P4 P5
P1 Left display (gouging current or name of adjustable parameter)
P2 Indicator lights for the current area
P3 Right display (gouging voltage or value of adjustable parameter)
P4 Setup button
P5 Control knob (gouging current adjustment, factory reset)
2. INSTALLATION
2.1 POSITIONING OF THE MACHINE
Place the machine on a rm, dry and level surface. Where possible, do not allow dust or other
impurities to enter the machines cooling air ow. Preferably site the machine above oor level;
for example on a suitable carriage unit.
Notes for positioning the machine
• The surface inclination should not exceed 15 degrees.
• Ensure the free circulation of the cooling air. There must be at least 20 cm of free space in
front of and behind the machine for cooling air to circulate.
• Protect the machine against heavy rain and direct sunshine.
NOTE! The machine should not be operated in the rain as the protection class of the machine, IP23S,
allows for outside preserving and storage only.
NOTE! Never aim metallic grinding spray/sparks towards the equipment.
5
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
2.2 CONNECTION TO MAINS
The KempGouge™ ARC 800 gouging power source is connected to a 400-V three-phase
network. The machine is delivered without a connection cable. The cable can be ordered
separately in lenght of 5 or 10 metres (see Ordering numbers).
Before use, check the connection cable and install a mains plug. If the cable does not comply
with the local electrical regulations, replace it with a compliant cable. For more information,
see the section Technical specications.
NOTE! The connection cable or plug may be installed or replaced by only an electrical contractor or
installer authorised to perform such operations.
Connecting the connection cable
1. Remove the right side plate. Be carefull when you unscrew the mounting screws of the
plastic edge, cause retaining nuts come out easily.
2. Pass the cable to the machine through the inlet ring at the rear of the machine, and
secure the cable with a cable clamp. Remember to use isolation between the cabel and
the cable clamp.
3. Connect the leads to the connectors as seen in the picture.
4. Fasten the side plate.
NOTE! Do not connect the zero lead if you are using a ve-lead cable.
L1
L2
L3
L4
L1 red
L2 black
L3 grey
L4 yellow-green
2.3 DISTRIBUTION NETWORK
All regular electrical devices without special circuits generate harmonic currents into
distribution network. High rates of harmonic current may cause losses and disturbance to
some equipment. This equipment complies with IEC 61000-3-12 provided that the short-
circuit power Ssc is greater than or equal to 7.6 MVA at the interface point between the user's
supply and the public supply network. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if necessary, that
the equipment is connected only to a supply with a short-circuit power Ssc greater than or
equal to 7.6 MVA.
6
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
2.4 GOUGING AND EARTHING CABLES
2.4.1 Connecting the gouging cable
The gouging cable is connected to the power source with a 120 mm2DIX connector. The
cable is connected either to the positive (+) or negative (-) connector of the power source,
depending on the metal that is to be worked. The power source has one negative connector
and two positive connectors. For information on the connector locations, see Introduction.
Connect the gouging cable as follows:
Work metal Gouging cable connection
Steel Positive (+)
Cast iron
Non-iron metal
Negative (-)
The gouging cable is rubber-insulated copper cable. The table below shows the typical load
capacities of the cables when the ambient temperature is 25 °C and the lead temperature is
85 °C.
Cable Duty cycle (ED) Voltage loss / 10 m
100 % 60 % 35 % 20 %
50 mm² 285 A 316 A 371 A 458 A 0.35V / 100 A
70 mm² 355 A 403 A 482 A 602 A 0.25V / 100 A
95 mm² 430 A 498 A 606 A 765 A 0.18V / 100 A
120 mm² 500 A 587 A 721 A 917 A 0.21V / 100 A
NOTE! Do not overload the gouging cables, as an overload may cause voltage loss and
overheating.
2.4.2 Connecting the earthing cable
The earthing cable is connected to the negative or positive connector in the power source,
depending on the connector used for the gouging cable (see Connecting the gouging cable).
The recommended cross-sections of the cable are listed in the table above.
Connect the earthing clamp directly to the work piece in such a way as to maximise the contact
surface of the clamp. The point of connection must be unpainted and free of corrosion.
3. USE
3.1 BEFORE YOU START
Before you start carbon-arc gouging, do the following:
• Select a gouging carbon suitable for the work piece and attach it to the carbon holder.
• Connect the gouging cable to the positive or negative connector depending on the type
of metal to be worked. For more information, see Connecting the gouging cable.
• Adjust the gouging current to a suitable level. By default, the machine uses the
adjustment of the last time the machine was used. For more information on the gouging
current, see the table below.
• Start the power source and start gouging. For more information on the proper way of
performing carbon-arc gouging, see Gouging techniques.
The currents recommended for various gouging carbons.
Round carbon size 5/32”
4.0 mm
3/12”
5.0 mm
1/4”
6.35 mm
5/16”
8.0 mm
3/8”
10.0 mm
1/2”
13.0 mm
Current (A) 80 – 150 110 – 200 170 – 330 230 – 450 300 – 550 460 – 900
Voltage (V) 38 – 41 39 – 42 43 – 46 44 – 48 46 – 50 46 – 50
7
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
3.2 HOW TO USE THE REMOTE CONTROL
1. Connect the R10 remote control unit to the service connection A7. Power source detects
the new device automatically, and the reference value of the remote control unit appears
on the display.
2. Set the desired gouging current with the remote control adjusting knob.
3. To stop using the remote control, disconnect it from the power source. The display starts
to show the gouging current that was used before connecting the remote control unit,
and the current control returns to the control panel.
3.3 STARTING OF THE POWER SOURCE
Start the power source by turning the main switch A2 on the front panel to the I position. The
standby indicator A3 turns on.
The cooling fan is started for a moment when the main switch is turned to the‘I’ position. The
fan turns o after a while and then restarts during gouging when the machine has warmed
up suciently. The fan continues running up to 10 minutes after gouging, depending on the
temperature of the machine.
NOTE! Always turn the device on and o using the main switch, not via the mains socket.
3.3.1 Automatic function test
During the power source start-up, the machine automatically performs a function test. The
test covers the following functions:
• Software version check. The left-hand side display shows the program version of
the control panel for one second. The display on the right displays the power source
program version.
• Indicator light and button functionality. All indicator lights and display segment LEDs
blink.
• System functions. If the system encounters a fault, a fault code is shown on the display.
• Implementation of factory settings or preset settings.
If the function test is successful, the machine is ready for use and the current and voltage
values are shown in the control panel.
If a fault has been detected in the function test, the display ashes the error code and the
yellow indicator light in the front panel of the power source blinks. For instructions, see
Troubleshooting.
3.3.2 Front panel indicators
The following indicators can be found on the front panel of the device:
• When the green indicator A3 is on, the power source is in standby mode. This indicator
is on when the machine is connected to the mains supply with the main switch in the ‘I’
position.
• When the yellow overheating indicator A4 is on, the machine has overheated. When the
indicator turns o, the machine can be used again.
• When indicator A4 blinks, the machine has encountered a failure. For instructions, see
Troubleshooting.
3.4 CONTROL PANEL FUNCTIONS
The control panel allows the user to control and monitor the operation of the machine.
The buttons and the control knob are used to adjust the current used in gouging and other
machine parameters. The current and voltage values are shown on the control panel displays
while working.
3.4.1 Adjusting the gouging current
The required gouging current is set with the control knob in the control panel. The accuracy
of adjustment is 10 A, which means that turning the control knob one notch increases or
decreases the current by 10 amperes.
If you turn the control knob quickly, you can quickly adjust the gouging current in increments
of 100 A for each notch.
8
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
The adjustment value of the gouging current is shown on the display when you turn the
control knob. The adjustment value is shown at the accuracy of 1 A. The indicator light A is
shown on the display. The values you use are stored in the control panel memory and will be
used when you start the machine again.
3.4.2 Actual gouging current and voltage display
While gouging, the control panel display shows the actual current and voltage values. The
gouging current is shown in amperes at the accuracy of 1 A, while the voltage is shown in
volts at the accuracy of 0.1 V.
3.4.3 Restoring factory settings
The control panel of the gouging power source has only one setting that the user can modify:
restore factory settings. This allows the user to restore the original welding current value and
clear the memory.
To restore the factory settings, do this:
1. Keep the Setup button in the control panel pressed for at least 5 seconds. The display
will read Set Up.
2. Release the Setup button. The display will read FAC OFF.
3. Turn the control knob until the display reads FAC ALL.
4. Briey press the Setup button in the control panel to perform factory reset.
3.5 TECHNIQUES FOR CARBONARC GOUGING
In practical carbon-arc gouging, note the following:
• Before you start working, make sure that the equipment is ready to use and that the
gouging current and the carbon have been selected according to the work piece.
• The pressure of the compressed air required in carbon-arc gouging is 500 – 700 kPa
(5 – 7 bar).
• Attach the gouging carbon (maximum size ø 13 mm) to the holder in such a way that the
free length of the carbon is 100 – 150 mm.
• Open the compressed air valve and take the tip of the carbon to the work piece.
• Ignite the arc by scratching the work piece with the gouging carbon.
• Move the gouging carbon in such a position that the compressed air ow hits the
molten material between the gouging carbon and the groove created.
• A suitable angle for gouging carbon is 20° – 45°. If the angle is greater, compressed air
cannot blow the molten metal away.
• Note that a gouged surface is not immediately ready for welding. Before welding, the
surface must be cleaned by grinding, for example.
NOTE! You must not exceed the maximum current specied for a gouging carbon as it will
accelerate carbon wear. The gouging current is too high if the copper coating melts faster than the
gouging carbon.
4. TROUBLESHOOTING
In the event of a failure of the machine, contact an authorised Kemppi service agent. Before
taking your unit for servicing, check the list below.
4.1 OVERLOAD YELLOW INDICATOR LIT
Two simultaneously operating fans cool both power sources of the machine. The machine
may, however, overheat if continuously loaded above the rated values or if the circulation of
cooling air is prevented.
The yellow indicator A4 is lit in the event of overheating. You then must stop gouging and let
the machine cool down. The indicator light turns o when gouging can be resumed.
9
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
4.2 CONTROL CABLE CONNECTOR FUSE
The rear wall of the power source contains fuse A9, which protects the control cable connector
A7. Using an incorrect fuse may cause damage to the power source. It is important that you
always use the right kind of fuse. The type and size of the fuse are indicated next to the fuse
socket.
4.3 CABLE NETWORK WITH OVER VOLTAGE OR UNDER VOLTAGE
If the power source is used in an electric network with insucient voltage (less than 300 V),
the control features of the device are automatically disabled.
The primary circuits of the power source are protected against power spikes. The product’s
mains voltage range is broad enough to prevent over-voltage problems at up to 440 V (see
Technical specications). Make sure that the voltage remains within the allowed range,
especially if the operating power is supplied by a generator set.
4.4 MISSING PHASE IN THE ELECTRIC NETWORK
If a phase is missing from the mains current, the gouging features will be adversely aected or
the machine may have problems starting. Loss of a phase can be caused by a:
• Blown mains fuse.
• Damaged connection cable.
• Poor connection cable connection in the machine’s terminal block or mains socket.
4.5 MACHINE ERROR CODES
The machine always checks its operation automatically during start-up and reports any
failures detected. If failures are detected during start-up, they are shown as error codes on the
control panel display.
Err3: Power source overvoltage
Gouging has been interrupted because dangerously high temporary voltage surges or a
continuous over-voltage has been detected in the electric network. Check the fuse size and
the quality of the supply network.
Err4: Power source overheating
The power source has overheated. The cause may be one of the following:
1. The power source has been used for a long time at maximum power.
2. The circulation of cooling air to the power source is blocked.
3. The cooling system has experienced a failure.
Remove any obstacle to air circulation, and wait until the power source fan has cooled down
the machine.
Err23: Power source overvoltage warning
The power source has detected voltage spikes in the electric network. Short power spikes can
be managed. They do not lead to interruptions in gouging but may decrease the quality of the
work. Check the quality of the supply network.
Other error codes:
The machine can show codes not listed here. In the event of an unlisted code appearing,
contact an authorised Kemppi service agent and report the error code shown.
10
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
5. SERVICE
The utilisation level of the power source and its working environment should be taken into
consideration in planning the frequency of maintenance of the machine. Appropriate use and
preventive maintenance guarantee the trouble-freest use of the equipment. This allows you to
avoid interruptions in use and increases the productivity of the machine.
5.1 CABLES
Check the condition of gouging and connection cables daily. Do not use damaged cables.
Also make sure that all extension cables used in the mains connection are in proper condition
and compliant with regulations.
NOTE! The connection cables may be repaired and installed only by electrical contractors and
installers authorised to perform such operations.
5.2 POWER SOURCE
Before cleaning the interior of the machine, you need to remove the case by unscrewing the
mounting screws at the top and sides of the machine.
NOTE! To prevent damage, wait approximately two minutes after disconnecting the connection
cable before removing the machine’s case.
Perform the following cleaning and maintenance at least every six months:
1. Clean the interior of the machine and the fan grill’s net of any dust and stains – for
example, with a soft brush and vacuum cleaner.
• Do not use pressurised air. The stain may become compressed into the grooves of the
coolers.
• Do not use a pressure-washing device.
2. Check the electrical connections of the machine. Clean any oxidised connections, and
tighten the loosened ones.
• Check for the right tension before you start repairing the connections.
NOTE! Remember that the machine may be repaired only by an electrical contractor or installer
authorised to perform such operations.
5.3 REGULAR MAINTENANCE
Authorised Kemppi service agents perform regular maintenance by agreement.
Tasks included in regular maintenance:
• Cleaning of equipment.
• Inspection and maintenance of the carbon holder.
• Checking of connectors, switches and adjusters.
• Checking of electrical connections.
• Checking of the connection cable and plug.
• Replacement of damaged or worn parts.
• Calibration testing, with adjustment of the functions and operational values of the
machine, if necessary.
5.4 DISPOSAL OF THE MACHINE
Do not dispose of electrical equipment with normal waste!
In observance of European Directive 2002/96/EC on waste electrical and electronic
equipment, and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and taken to an appropriate
environmentally responsible recycling facility.
The owner of the equipment is obliged to deliver a decommissioned unit to a regional
collection centre, per the instructions of local authorities or a Kemppi representative. By
applying this European Directive you will improve the environment and human health.
11
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
6. ORDERING NUMBERS
KempGouge ARC 800 (incl. transport unit) 6284000
Connector cable 4 X 16 mm, 5 m W000869
Connector cable 4 X 16 mm, 10 m W003408
Earthing cable 95 mm², 5 m (DIX120) 61840951
Earthing cable 95 mm², 10 m (DIX120) 61840952
Earthing cable 120 mm², 5 m 61841201
Earthing cable 120 mm², 10 m 61841202
Remote control R10 6185409
7. TECHNICAL SPECIFICATIONS
KempGouge ARC 800
Connection voltage 3~ 50/60 Hz 400V -15 ... +20%
Rated power 50% ED 44 kVA
100% ED 35 kVA
Primary current 50% ED I1max 65 A
100% ED I151 A
Connection cable H07RN-F 4G16 (16 mm²)
Fuse (recommended) 63 A delayed
Idle power 120W
Efficiency 0.90
Power factor 0.90
Load capacity at 40 °C 50% ED 800 A / 44V
100% ED 600 A / 44V
Current adjustment range 20 A – 800 A
Open circuit voltage 50V
Gouging carbon max. size ø 13 mm
Recommended pressure of the
compressed air
500 – 700 kPa (5 – 7 bar)
Storage temperature range -40 °C ... +60 °C
Operating temperature range -20 °C ... +40 °C
EMC class A
Minimun short circuit power Ssc of
supply network *
7.6 MVA
Degree of protection IP23S
Dimensions
(without/with transport unit)
Length 590/700 mm
Width 230/660 mm
Height 885/1,400 mm
Weight 94/115 kg
Maximum load of lifting lug 200 kg
* See paragraph 2.3.
12
KempGouge ARC 800 / © Kemppi Oy / 1117

EN
13
KempGouge ARC 800 / © Kemppi Oy / 1117

www.kemppi.com
1928400
1117
KEMPPI OY
Hennalankatu 39
PL 13
FIN-15801 LAHTI
FINLAND
Tel [phone]
Telefax [phone]
[email protected]
www.kemppi.com
Kotimaan myynti:
Tel [phone]
Telefax [phone]
myynti.@kemppi.com
KEMPPI SVERIGE AB
Box 717
S-194 27 UPPLANDS VÄSBY
SVERIGE
Tel [phone]
Telefax [phone]
[e-mail]
KEMPPI NORGE A/S
Postboks 2151, Postterminalen
N-3103TØNSBERG
NORGE
Tel [phone]
Telefax [phone]
[e-mail]
KEMPPI DANMARK A/S
Literbuen 11
DK-2740 SKOVLUNDE
DANMARK
Tel [phone]
Telefax [phone]
[e-mail]
KEMPPI BENELUX B.V.
Postbus 5603
NL-4801 EA BREDA
NEDERLAND
Tel [phone]
Telefax [phone]
[e-mail]
KEMPPI (UK) Ltd
Martti Kemppi Building
Fraser Road
Priory Business Park
BEDFORD, MK44 3WH
UNITED KINGDOM
Tel [phone]
Telefax [phone]
[e-mail]
KEMPPI FRANCE S.A.S.
65 Avenue de la Couronne des Prés
78681 EPONE CEDEX
FRANCE
Tel [phone]
Telefax [phone]
[e-mail]
KEMPPI GmbH
Otto-Hahn-Straße 14
D-35510 BUTZBACH
DEUTSCHLAND
Tel [phone]
Telefax [phone]
[e-mail]
KEMPPI SPÓŁKA Z O.O.
Ul. Borzymowska 32
03-565WARSZAWA
POLAND
Tel [phone]
Telefax [phone]
info[email protected]om
KEMPPI AUSTRALIA PTY LTD.
13 Cullen Place
P.O. Box 5256, Greystanes NSW 2145
SMITHFIELD NSW 2164
AUSTRALIA
Tel. [phone]
Telefax [phone]
info[email protected]om
OOO KEMPPI
Polkovaya str. 1, Building 6
127018 MOSCOW
RUSSIA
Tel [phone]
Telefax [phone]
info[email protected]om
ООО КЕМППИ
.  1,  6
127018 
Tel [phone]
Telefax [phone]
info[email protected]om
KEMPPI, TRADING (BEIJING) COMPANY,
LIMITED
Room 420, 3 Zone, Building B,
No.12 Hongda North Street,
Beijing Economic Development Zone,
100176 Beijing
CHINA
Tel [phone]
[phone]
Telefax [phone]
[e-mail]
肯倍贸易（北京）有限公司
中国北京经济技术开发区宏达北路12号
创新大厦B座三区420室 (100176)
电话： [phone]
[phone]
传真： [phone]
[e-mail]
KEMPPI INDIA PVT LTD
LAKSHMITOWERS
New No. 2/770,
First Main Road,
KAZURA Gardens,
Neelangarai,
CHENNAI - 600 041
TAMIL NADU
Tel [phone]
Telefax [phone]
[e-mail]