Keys Fitness Inversion Table IT-2 User manual

Owner’s Manual
INVERSION TABLE
Customer Service
1.888.340.0482
Keys Fitness
4009 Distribution Drive
Suite 250
Garland, TX 75041
www.keysfitness.com
Read all precautions and instruc-
tions in this manual before using
this equipment.
215-00006
08/04
IT-2

Table of Contents
2
Important Safety Information 3
Before You Start 4
Assembly 5-10
Operation 11-12
Exploded View 13
Parts List 14
Warranty 15

Important Safety Information
3
WARNING:
Before beginning this or any exercise program consult your physician. This is especially important for persons
over the age of 35 or persons with pre-existing health problems. Read all instructions in this manual before
using this product. Keys Fitness assumes no responsibility for personal injury or property damage sustained by
or through the use of this product.
1. Inspect and tighten all parts each time you use the unit. Replace any worn parts by contacting your local
dealer or Keys Fitness Customer Service at [phone].
2. Keep your hands and other parts of your body away from moving parts other than designed handles.
3. Keep small children away from the unit at all times.
4. When adjusting the height make sure the pins are firmly in place. Failure secure the pins firmly may
result in injury.
5. If you feel pain or dizziness at any time while using this unit stop immediately and begin cooling down.
6. This unit a has maximum user capacity of 250 pounds.

Before You Start
4
Before use, read instruction manual completely.
It is extremely important to set the balance for your proper height and weight before use to avoid injury.
Remove footwear before use. (You could slip out of your shoes and cause injury.) Both feet must be placed in
the footrest.
First time users should have someone in attendance.
Keeps hands and finger clear from underneath sliding back rest to avoid injury.
Please consult your physician for any questions concerning health risks.
Keeps fingers clear of foot adjustment ratchet to avoid injury.
Caution is advised in certain medial pre-existing conditions.
Always consult your physician before starting regular use.
If you suffer from any of the following conditions do not use this equipment:
GLAUCOMA, DETACHED RETINA, CONJUNCTIVITIS, UNCONTROLLED HYPERTENSION (HIGH BLOOD PRESSURE),
IMPAIRED PULMONARY FUNCTIONS, ARRHYTHMIA, CAROTID ARTERY STENOSIS, SERVE VASCULAR DISEASE,
ANEURYSM, TENDENCY TOWARDS FAINTING OR DIZZY SPELLS, CEREBRAL SCLEROSIS, RECENT STROKE OR
TRANSIENT ISCHEMIC ATTACK, HISTORY OF BRAIN LESIONS, OTHER HEART OR CIRCULATORY DISORDERS FOR
WHICH YOU ARE BEING TREATED, SEVERE BACK PROBLEMS OR SPINAL INJURIES, BONE WEAKNESS (OSTEO-
POROSIS), RECENT UNHEALED FRACTURES, MEDULLARY PINS, ARTIFICIAL HIP JOINTS OR OTHER ORTHOPEDIC
SUPPORTS SURGICALLY IMPLANTED, MIDDLE EAR INFECTION, RECENTLY HAD MAJOR SURGERY, USING SPE-
CIAL MEDICATION, VENTRAL OR HIATAL HERNIA, TENDENCY TOWARDS BLEEDING, EXTREME OBESITY, INVER-
TAPHOBIA (FEAR OF INVERSION), AND PREGNANCY.
This is not a complete list. Should you have a condition or ailment that you think would restrict usage of this
unit, please consult a physician or therapist before continuing.

Assembly
5
Hardware
List

Assembly
6

STEP 1
Spread the Front Support (1) and Rear
Support (2) of the base apart as shown
in Figure 1. Carefully push down on the
two folding arms until they are fully
lock in place.
STEP 2
Slide the Nylon Covers (28) onto the top
of the base assembly. The covers should
extend slightly below the Side Adjustable
Frame (2). Use the velcro straps to secure
them in place. (Figure 2)
Assembly
7
Figure 2
Figure 1

Assembly
8
STEP 3
Slide the Adjustable Frame (3) into the tube of
the Main Frame (4). Set your desired height
using the Black Ball Pen (12) and secure in place
with the Knob Bolt 3/4” (14). (Figure 3)
Step 4
Insert the Foam Rod (9) through the holes at the
bottom of the Adjustable Frame (3). Use one Hex
Bolt M6*48mm (33), two Washers M6 (37), and
one Locknut M6 (39) to secure the rod in place.
Next, place one of the Roller Pads (40) into a
Foot Foam Brackets (10) and slide one onto each
end of the Foam Rod (9). Make sure the holes of
both the Foot Foam Bracket (10) and the Roller
Pads (40) line up together. Insert the Foot Frame
(6) into the Adjustable Frame (3) and secure in
place using Knob Bolt M8 (15). (Figure 4)
Figure 3
Figure 4

Assembly
9
Step 5
Insert Front Adjustable Frame (5) into the top of the Adjustable Frame (3). Pull the rope down and hook the
end of the spring onto the Hex Bolt M6*48mm (33) as shown in Figure 5b.
Figure 5a
Figure 5b

Step 6
Slide a Pivot Arm (7) into each brace
located on the left and right side of the
Main Frame (4). Carefully set Unit A into
the notches at the top of Unit B. Connect
the Long Strap (30) to the Short Strap (29)
as shown in Figure 6b. Last, attach the
hook end of the Long Strap (30) to the
weld ring of the Front Support (1) and the
hook end of the Short Strap (29) to the
weld ring of the Main Frame (4). (Figure
6c)
Assembly
10
Congratulations!
You have completed the assembly of the IT-2 Inversion Table.
Figure 6a
Figure 6b
Figure 6