Keys Fitness Horizontal Pressing Station KPS-2050 User manual

Owner’s Manual
Read all precautions and instruc-
tions in this manual before using
this equipment.
215-00010
09/04

Table of Contents
2
Important Safety Information 3
Before You Start 4
Assembly 5-40
Weight Ratios 41
Weight Stack Sticker Placement 42
Cable View 43
Top View 44
Exploded View 45
Parts List 46
Warranty Information 47

Important Safety Information
3
THANK YOU for making this Power System unit a part of your exercise pro-
gram. Keys Fitness and our Power System Series assures the very best in value,
appearance, durability and biomechanics.
This manual will guide you through the assembly process. If at any time you are
having trouble with the assembly or use of this product, then please contact us at
our Keys Fitness Help-line. We have trained service technicians on site to take
care of you, our valued customer.
REGISTRATION CARD
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register on-line at www.keysfitness.com within 10 days
of purchase.
POWER SYSTEM SERIES
QUESTIONS?
CALL
1-888-340-0482
Monday-Friday
8:30-5:30 Central Time
When calling please have the following product information available:
• Product Series
• Model #
• PO # (located on the front of the manual)
• Part Number
• Part Description

Before You Start
4
Prior to assembly, remove components from the box and verify that all the listed parts were supplied.
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
SAFETY INFORMATION WARNING!
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with
pre-existing health problems. Keys Fitness Products LP assumes no responsibili-
ty for personal injury or property damage sustained by or through the use of this
product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
SAFETY PRECAUTIONS
• This Power System unit should only be used on a level surface and is intended
for indoor use only. Keys Fitness recommends an equipment mat be placed
under the unit to protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate
clothing. Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.
• Service to your Power System unit should only be performed by an authorized
service representative, unless authorized and/or instructed by a Keys Fitness
technician. Failure to follow these instructions will void the warranty.

Assembly
5
Box 1

Assembly
6
Box 2

Assembly
7
Box 3

Assembly
8
Box 4

Assembly
9
Box 5

Assembly
10
Box 6

Assembly
11
Box 7 Box 8
Box 10
Box 12
Box 9
Box 11

Assembly
12

Assembly
13

Assembly
14

Step 1
Attach Right Base Frame (4) to Rear Frame (1) using two Nuts (144), four Washers (143),
and two Bolts (137).
Attach Left Base Frame (8) to Rear Frame (1) using two Nuts (144), four Washers (143), and
two Bolts (137).
Insert Guide Rods (47) into Rear Frame (1). Next, slide Weight Stack Bumpers (99) onto
Guide Rods (47).
Attach Rear Upright (3) to Rear Frame (1) using two Nuts (144), four Washers (143), and
two Bolts (136).
Assembly
15
Figure 1

Assembly
16
Step 2
Slide the weight plates down the Guide Rods (47) in this order - five 15lb Plates (52), nine 10lb Plates (53),
five 5lb Plates (54), and the Top Plate (55). Note: Number of weight plates may vary depending on your spe-
cific configuration.
Attach Up Frame (2) to all four Guide Rods (47) and secure to Rear Upright (3) using two Nuts (144), four
Washers (143), and two Bolts (136).
Figure 2

Assembly
17
Step 3
Attach Front Upright (19) to Seat Pad Support Receptacle (6) using two Nuts (144), four Washers (143), and
two Bolts (136).
Attach Seat Pad Support Receptacle (6) to Base Frame assembly using two Nuts (144), four Washers (143),
and two Bolts (136).
Figure 3

Step 4
Attach Main Upright (7) to Seat Pad Support Receptacle (6) using two Nuts (126), four Washers (125), and
two Bolts (131).
Attach Right Top Frame (5) to Up Frame assembly using two Nuts (144), four Washers (143), and two Bolts
(137). Next, use two Washers (143), two Spring Washers (119), and two Allen Bolts (142) to connect Right
Top Frame (5).
Assembly
18
Figure 4

Step 5
Slide Press Station Base Frame (11) over Press Arm Support (10). Next, attach both pieces to Base Frame
using two Nuts (144), four Washers (143), and two Bolts (134).
Install Left Top Frame (9) over Press Arm Support (10) and Top Frame assembly. Secure top section using
two Nuts (144), four Washers (143), and two Bolts (137). Next, Secure lower section using two Nuts (144),
four Washers (143), and two Bolts (136). Secure top of Guide Rods (47) using two Washers (143), two Spring
Washers (119), and two Allen Bolts (142).
Assembly
19
Figure 5

Assembly
20
Step 6
Attach Pec Dec Mount (21) onto Seat Pad Support Receptacle (6) using two Nuts (144), four Washers (143),
and two Bolts (136). Secure in place with one Washer (129), one Spring Washer (119), and one Bolt (137).
Figure 6