Kichler Lighting Imari 65 User manual

INSTRUCTION MANUAL
Model#: 300365
Product images may vary slightly from actual product.
65" Imari
READ AND SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS
SAFETY RULES..................................................................3
TOOLS REQUIRED............................................................4
PACKAGE CONTENTS ....................................................4
MOUNTING OPTIONS.....................................................5
HANGING THE FAN......................................................... 6
INSTALLATION OF SAFETY CABLE ......................... 9
ELECTRICAL CONNECTIONS ................................. 10
FINISHING THE INSTALLATION................................12
ATTACHING THE FAN BLADES.................................13
INSTALLING THE LIGHT PLATE ...............................13
INSTALLING THE LED LIGHT
KIT AND DECORATIVE RING ......................................14
CONTROL SYSTEM SET-UP......................................15
BUTTON INSTRUCTION...............................................16
SENSORLESS DC CONTROL
PAIRING PROCEDURES...............................................17
INSTALLING THE WALL CONTROL
SYSTEM WALL PLATE.................................................. 18
OPERATING INSTRUCTIONS.....................................19
TROUBLESHOOTING...................................................20
FCC INFORMATION ......................................................22
2 | KICHLER.COM

SAFETY RULES
1. CAUTION – RISK OF SHOCK – Disconnect Power at the main
circuit breaker panel or main fusebox before starting and during the
installation.
2. WARNING: All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70” and local electrical codes.
Electrical installation should be performed by a qualified licensed
electrician.
3. WARNING: To reduce the risk of electric shock, this fan must be
installed with a general-use, isolating wall control/switch.
4. WARNING: Not suitable for use with solid-state speed controls.
5. WARNING: To reduce the risk of fire, electric shock, or personal
injury, mount to outlet box marked “acceptable for fan support of
15.9 kg (35 lbs.) or less” and use mounting screws provided with the
outlet box. Most outlet boxes commonly used for the support of
light fixtures are not acceptable for fan support and may need to
be replaced. Due to the complexity of the installation of this fan, a
qualified licensed electrician is strongly recommended.
6. The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 15.9 kg (35 pounds). Use
only cULus Listed outlet boxes marked “Acceptable for Fan Support
of 15.9 kg (35 lbs) or less”.
7. The fan must be mounted with a minimum of 2.1 m (7 feet) clearance
from the trailing edge of the blades to the floor.
8. To operate the reverse function on this fan, press the reverse
button while the fan is running.
9. Avoid placing objects in the path of the blades.
10. WARNING: make sure the power is disconnected before cleaning
your fan.
11. To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
12. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be suitable
for most cleaning.
13. After making electrical connections, spliced conductors should
be turned upward and pushed carefully up into outlet box. The
wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box and
the ungrounded conductor on the other side of the outlet box.
14. Electrical diagrams are reference only. Light kits that are not
packed with the fan must be cULus Listed and marked suitable for
use with the model fan you are installing. Switches must be cULus
General Use Switches. Refer to the Instructions packaged with the
light kits and switches for proper assembly.
15. All set screws must be checked, and retightened where necessary,
before installation.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO
NOT BEND THE BLADE BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER INSTALLATION.
DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.
N.W. 10.2 KGS (22.4 LBS) / G.W. 12.3 KGS (27.1 LBS)
65" Imari | 3

TOOLS REQUIRED
PACKAGE CONTENTS
Unpack your fan and check the contents . You should have the following items:
A. Fan Blades (3)
B. Canopy & Ceiling
Mounting Bracket
C. Ball/Downrod Assembly
D. Coupling Cover
E. Fan Motor Assembly
F. Light Plate
G. 25W LED Light Kit
H. Decorative Ring
I. Receiver
J. Wall Transmitter
K. Part Bag Contents
1) Mounting Hardware:
Wire Nuts (3)
2) Blade Attachment Hardware:
Screws with Lock Washers (9),
Flat Washers (9)
• Phillips Screwdriver
• Blade Screwdriver
• 11 mm Wrench
• Step Ladder
• Wire Cutters
A
B
C
D
E
F
G
H
I
J
K
4 | KICHLER.COM

MOUNTING OPTIONS
If there isn’t an existing UL (cUL for Canadian Installation) listed
mounting box, then read the following instructions. Disconnect
the power by removing fuses or turning o circuit breakers.
Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box
and its support must be able to fully support the full weight
of the fan (up to 15.9 kg (35 pounds)). Do not use plastic outlet
boxes.
Figures 1, 2 and 3 are examples of dierent ways to mount the
outlet box.
NOTE: If you are installing the ceiling fan on a sloped (vaulted)
ceiling, you may need a longer downrod to maintain proper
clearance between the tip of the blade and the ceiling. A
minimum clearance of 12" is suggested for optimal operation.
NOTE: Depending on the location you have selected for
installation, you may need to purchase and install a “Joist
Hanger” for the support of the outlet box. Make sure the joist
hanger you purchase has been designed for use with ceiling
fans. (Fig. 4)
Fig. 1
Outlet box
Outlet box
Fig. 2
Fig. 3
Fig. 4
Outlet box
Recessed
outlet box ceiling
Ceiling
mounting
plane
Provide strong
support
ANGLED CEILING
MAXIMUM 30° ANGLE
65" Imari | 5

HANGING THE FAN
REMEMBER to turn o the power before you begin.
To properly install your ceiling fan, follow the steps below.
Step 1. Remove the decorative canopy bottom cover from the canopy by
turning the cover counter clockwise. (Fig. 5)
Step 2. Remove the ceiling mounting bracket from the canopy by removing
and saving one of the two screws. Loosen the remaining screw by a half turn.
(Fig. 5)
Step 3. Pass the 120 volt supply wires from the ceiling outlet box through the
center of the ceiling mounting bracket. (Fig. 6)
Step 4. Attach the ceiling mounting bracket to the outlet box using the
screws and washers included with the outlet box. (Fig.6)
Hanger Bracket
Fig. 5
Fig. 6
Ceiling
Canopy
Canopy
Cover
cULus Listed
Electrical
Box
120V Wires
Washers
Mounting Screws
(Supplied with Electrical Box)
Ceiling
Mounting
Bracket
6 | KICHLER.COM

HANGING THE FAN
(continued)
WARNING: All set screws must be checked, and retightened where
necessary, before installation.
Step 5. Remove the hanger ball from the downrod assembly by loosening
the set screw, unscrewing and removing the cross pin and unscrewing the
ball o the rod. (Fig. 7)
Step 6. Loosen the two set screws and remove the hitch pin and retaining
clip from the coupling on top of the motor assembly. (Fig. 8)
Step 7. Carefully feed the electrical lead wires from the fan up through the
downrod. Thread the downrod into the coupling until the Hitch pin holes
are aligned.
Next, replace the hitch pin and retaining clip. Tighten both set screws. (Fig. 8)
NOTE: This fan comes with a 6" downrod. please cut o the electrical lead
wires If you do not plan use a longer downrod.
Fig. 7
Fig. 8
Cross Pin
Hanger
Ball Set Screw
Download
Supply Wires
Downrod
Set Screws
Set Screws
Hitch Pin
Retaining Clip
65" Imari | 7

HANGING THE FAN (continued)
Step 8. Slip the coupling cover, secure ring , canopy cover and canopy
onto the downrod. (Fig. 9)
Thread the hanger ball onto the downrod, insert the cross pin through
the downrod and tighten. Now tighten the set screw. (Fig. 9)
Step 9. Lift the motor assembly into position and place the hanger ball
into the ceiling mounting bracket.
Rotate the entire assembly until the “Check Tab” has dropped into the
“Registration Slot” and seats firmly. (Fig. 10)
The entire motor assembly should not rotate (left or right) when seated
properly.
WARNING: Failure to reattach the cross pin and seat the “Check Tab” can
cause the fan to fall from the ceiling during operation. Take special care to
make sure this pin is reattached.
Fig. 9
Fig. 10
Canopy
Coupling Cover
Downrod
Canopy Cover
Set Screws
Hitch Pin Retaining
Clip
Registration
Slot
8 | KICHLER.COM

INSTALLATION OF SAFETY CABLE
(required for Canadian installation ONLY)
A safety support cable is provided to help prevent the ceiling fan from falling,
please install it as follows.
Step 1. Attach the wood screw and washers to the ceiling joist next to the
mounting bracket but do not tighten. (Fig. 11)
Step 2. Adjust the length of the safety cable to reach the screw and washers by
pulling the extra cable through the cable clamp until the overall length is correct,
put the end of the cable back through the cable clamp, forming a loop at the end
of the cable. Tighten the cable clamp securely. Now, put the loop in the end of
the safety cable over the wood screw and under the washer. Tighten the wood
screw securely.
NOTE: Although the safety support cable is required for Canadian installations
only. It’s a good idea to make the attachment with any installation.
Step 3. Insert the receiver into the ceiling mounting bracket with the flat side
of the receiver facing the ceiling. (Fig. 12) For best performance, make sure the
Black Antenna, on the end of the receiver, remains extended and not tangled
with any of the electrical wires.
Fig. 11
Attach safety cable
to ceiling joist with
screw and washer
Ceiling mounting
bracket
Fig. 12
Receiver
Hanger
Bracket
65" Imari | 9

ELECTRICAL CONNECTIONS
WARNING: Carefully read and retain this Instruction Manual
for future reference.
WARNING: To avoid possible electrical shock, be sure the
electricity is turned o at the main panel by removing the fuse
or opening the circuit breaker.
WARNING: This control is designed for use with “DC Motor
Ceiling Fans” ONLY. DO NOT use with any other type of
electrical appliance.
WARNING: All wiring must conform to national and local
electrical codes. If you feel you do not have enough electrical
knowledge, have a licensed electrician install the control.
WARNING: The amperage for your fan should not exceed 1A.
The total wattage for the lights 300W.
Make each of the wire connections illustrated in Figure 13.
Secure each with the wire nuts provided.
A. CEILING FAN TO RECEIVER WIRE CONNECTION
Step 1. Connect the Blue wire from the fan (motor) to the Blue
wire from the receiver. White wire from the fan (motor) to the
White wire from the receiver. Red wire from the fan (motor) to
the Red wire from the receiver. Gray wire from the fan (motor)
to the Gray wire from the receiver. (Fig. 13)
Step 2. If you do not plan to use the light kit with your fan at this
time, please DO NOT connect the Blue and White wires, and
respectively secure the blue and white wires with the wire nut.
B. RECEIVER TO HOUSEHOLD WIRE CONNECTION
Step 1. Snap together the 2-P wire connection plugs from the
receiver and filter: Black to black , White to white. (Fig. 13)
Step 2. Connect the Ground conductor of the 120V supply to
the one Green wire from filter and one from the fan.
C. WALL CONTROL WIRE CONNECTION
Step 1. Black wire (TO MOTOR L) from the Wall Control to the
Black wire from the Wall Outlet Box. (Fig. 13)
Step 2. Black wire (AC IN L) from the Wall Control to the Black
wire from the Wall Outlet Box.
Step 3. Your wall outlet box has a ground wire (green or bare
copper), connect the wall control’s yellow/green ground wire
to it.
10 | KICHLER.COM